Wood Finishing For Sale

Custom-Built DEIMCO Through Feed Sprayer with a BLASDEL IR Preheat Tunnel that is available MARCH of 2023. Until then, the System can be seen in operation. -- Line was designed to preheat Fiber Cement board prior to painting and is followed by a Single-Arm Reciprocating Sprayer with 4-Spray Gun cap. Spray Guns not included.SEE ATTACHED VIDEO FOR A GOOD LOOK AT THE LINE's OPERATION!Built in 2019, the System was used for approx. (2) years; current owner changed their process and no longer requires the equipment.Oven width cap.: 60" Wide, 1-3/4" part height cap.; overall Oven dimension: 84" Wide x 12-1/2' long x 55" high, excluding the Blower & Stack. Line/Conveyor: Variable speed drive, 18.5 FPM to 26 FPM; Reciprocator operates up to 260 FPM and set by the HMI. 2-Zone Oven: -- Zone 1: (2) Upper left side wall/ceiling mounted; 18" x 60" emitters. -- Zone 2: (2) Right upper side wall/ceiling mounted 18" x 60" emitters; 8" clearance between emitters & rolls. Heaters: Natural gas using 7" WC; 480 Volt preheat; TC, FM, flange frame. - Gas Ratings: 360,000 BTUH Max. input ; 100,000 BTUH standby input; Air Exhaust on infeed & Injection Blower on outfeed. Electrical ratings: 26.6 Amps, 480 V - 3 Phase, 60 Hz.Exhaust: 980 CFM, 1 HP Motor.Control Panel: 60 AMP Disconnect switch, ALLEN-BRADLEY "Panel View Plus HM", IEC contactor & High Temp PID exhaust.NOTE: (25) New replacement conveyor rollers & (40) reconditioned rollers for IR Tunnel.DIEMCO Sprayer complete with: (1) Reciprocating Arm holds (4) guns and reads the leading & trailing edge to turn on & off the guns as the parts feed through; best to run full width loads through Sprayer; Overspray funnels into buckets.Spray Guns turn on & off based on the part leading & trailing edge; read by a light curtain on the infeed end.Dims: GFS Spray Cabin: 13' Deep x 8-1/2' wide x 9' high surround the reciprocating arm. - Filter & Exhaust Section: 13' Wide x 3' Deep x 10' High.

DEIMCO MFM-98 ACRYLIC COATING FINISHING SYSTEM: -- Specifications:Drying Oven for the purpose of baking and drying the acrylic finish onto lumber and panel products. 3"; dia. x 21.625" long Rollers on 12"; centers; Infeed: 16' long In-feed Conveyor, 10' long Transfer Conveyor, 12' long Oven Conveyor: DEIMCO MFM-98 ACRYLIC COATING FINISHING SYSTEM: -- Specifications:Drying Oven for the purpose of baking and drying the acrylic finish onto lumber and panel products. 3"; dia. x 21.625" long Rollers on 12"; centers; Infeed: -- Operator & Machine Control:Built with Allen Bradley/Honeywell Components, MFM Serial: 1177, Voltage: 460V/60 Hz/25 Amp, Air: 1"; NPT 90PSIG -- Complete With:Electrically Heated Oven; 8 Cool Down Fans; 2 - Hydraulic Lift Tables; Panel Machine with Hydraulic Pump; 15’ Flash Off Conveyor; 40’ Cool Down Conveyor Includes the following for (two) flood coat machines, Conveyor System, Arbors, Paint Pump, Hydraulic Pump, Hydraulic Lift Table -- Options Complete Over-all Foot Print 175’ long x 50’ wide

DUBOIS Vertical Edge Fill System with Micro UV This machine is designed to fill voids and defects in edges for a smooth, quality finish. These coaters are ideal for filling porous open grain panels like oak, veneers, particleboard, and MDF. Compatible with solvent based, water based, and UV fill coating.1.1 One (1) Continuous chain transport system- Top and Bottom chain transport conveyor with speed matching attachment conveyor chain- Aluminum backed chain pads with EPDM covering1.2 Two (2) double sided vertical edge denibber/buffer- Operator side Adjustable up to 12"; wide, back side fixed edge- Post mounted vertical denibber head- 12"; dia. x silicon impregnated scuffing wheel, buffer wheel to be determined- Dust hood with 4"; connection- Vertical head oscillation for even brush wear- Inverter controlled drive provides speed control for brush and oscillation1.3 Two (2) double sided vertical edge fill stations- Operator side Adjustable up to 12"; wide, back side fixed edge- Electric motor driven Applicator and Doctor roll drives- Quick change applicator sleeve design, 1-1/2"; face- Stainless steel distribution pipe with spring tension- 9"; dia. chrome plated reverse roll- Stainless steel catch pan and drain lines- 3/8"; pail mounted pump and agitator- Spring loaded doctor bar, urethane dr. blade- Air cylinder dr. roll engagement with stroke adjuster- Inverter controlled drives provides speed control for applicator and doctorrolls1.4 Edge Cure UV Oven Banks- Each bank to consist of Two (2) double sided Fusion F600 Microwave UVovens- Space for two (2) future double sided Microwave UV Units- Individually adjustable three (3) position lamp power selector switch(300, 400 & 600 w/in.)- Irradiator cooling exhaust fan for each set of four (4)2. Control Panel System- NEMA 12 Hinged Door Enclosure, with disconnect, required fuses, door mounted buttons and cooling fans- Allen Bradley HMI, PLC items included- Top mounted panel cooling fan- Required Inverters· Edge Fill Finishing Machineo Top and Bottom Conveyor driveso Denibber/Buffer Brusheso Denibber/Buffer oscillatorso Applicator Rollso Doctor Rollso Reverse Rollso UV oven Exhaust fansDesign Parameters- Machine is located in Explosion Proof Area- Voltage= 480 V., 3 Ph., 60 Hz.- Design Speed = 70 - 200 FPM- Line height = 36";- Max./Min. Part Width: 12"; / 2";- Max./Min Part Length: 245"; / 24";- Max./Min Part Thickness: 1-1/4"; / 3/8";- Paint Color· Main Frame and Conveyor: Blue / TS White· Guards: safety yellowNotes:- ¼"; product has the potential of being processed in this machine but has less probably of being successful the wider the product.

The Dubois SP-12 Linear Spray Machine is an automated linear finishing machine that can be used for a variety of applications including priming, staining, sealing, lacquering, etc. of linear stock. This spayer comes with (3) three arms, (3) three guns and (1) one paint pump. The guns are Binks spray guns Model 363, and Binks pump.Compatible with both waterborne and solvent based coatings --Three adjustable gun arms --9’-0"; long variable speed live roll conveyor w/ electric powered drive --Pneumatic gun trigger mechanism to automatically trigger guns on/off --Infeed guide fences --Top roller hold-down on infeed table --Ability to enable/disable individual guns --Easily cleaned spray trough --Adjustable atomizing air pressure --Adjustable fluid pressureIncluded optional features: &#9679 Stain wipe station mounted to outfeed with stain wipe brush &#9679 Exhaust system with spray enclosure, exhaust fan, & exhaust filter system &#9679 Denibbing station mounted to infeed

Dubois Gas Fired Oven

Dubois Lineal Sprayer with Guns

Cabinet Door Finishing System --4 Air Spray Guns --3 different lines and pumps --Paper feed belt with various speed options --Infrared sensors detect exact measurements of cabinet doors or mouldings and spray only the pieces being sent through. --System includes: (1) Dry Room and fan for air movement. --System is in great condition and works well. Our shop got to the point where we were really only using it to prime doors and it is capable of so much more than that.

Photos coming! System includes: 24” in-line sander- Single head with buffing roller and clean up brush $340024” Double roll coaters 3ea-24” 2 bulb UV ovens 4ea24” Reverse rollcoaters 2ea24” 3 head brush denibber with double cleanup brushes 53” 2006 Heeseman sander- head 1 is a drum, head 2 is a cross belt, head 3 is a pad and has a clean up brush

FIN - ST 1600, ...Top/Bottom Cleaning Brush.62" Width and 3-1/8" max. thickness opening, thickness adjustment by handwheel via worm gear with dial indicator.Equipped with: -- Top & Bottom nylon brushes driven by 3 HP drive motor (only 1-brush with machine). -- Separate variable speed feed motor with magnetic controls driving 3" dia. rubberized infeed & outfeed pinch rolls. -- Full fabricated sheet metal enclosure for efficient dust collection, dust enclosure hood with central 6" dia. dust outlet connection.

GIARDINA DUALTECH 605 Automatic Reciprocating Sprayer:GIARDINA, model DUALTECH 605. Automatic reciprocating Spray Machine.System includes: -- In-feed roller conveyor with panel reading/detection 60-cell photodiode bar to monitor and regulate spray application, further maximizing application transfer efficiency. -- (2) Reciprocating trolleys with spray gun supports, and adjustable speed, providing a consistent speed and pattern across entire conveyor width. - Each trolley to carry (4) adjustable guns on each head (8 guns total). -- Two (2) coating circuits, suitable for solvent and water-based coatings. -- Motorized height adjustments of spray gun supports. -- Spray guns are independently adjustable in inclination; and manual adjustment. -- Through Feed Conveyor: Max. working width of 1,300 mm (51"), variable speed adjustable by means of an inverter. -- Synthetic Belt Conveyor: Ring-closed by means of an "overlapped" joint and with solvent-resistant surface treatment.Features: -- Total recovery of the lacquer deposited on the belt and cleaning of the belt with the possibility of reusing it in the spraying circuit. - Rapid repositioning of the conveyor belt system thanks to the special design of the frame. -- Air exhaust system and separation of the solid content from the air by means of two (2) suction boxes located on the two sides of the conveyor, equipped with high-efficiency twin Dry-Filters. The filtered air is exhausted to the outside by means of a centrifugal fan. -- The Enclosure Booth is made with structural irons and coated sheet steel panels. -- Control and set-up of the work parameters by means of a PLC located on a pivoting arm mounted to the machine.NOTE: Is being "Cleaned, checked and Serviced" by on of the most experienced Finishing Equipment Technician!

HEESEMANN - KSA 8 CSD, ...Lacquer/Sealer Sander w/80" Belt WidthThis is a Very Special "extra wide" HEESEMANN equipped with: HEESEMANN's patented "CSD" selective pressure adjustment system, sensors placed every 5/8" (16 mm) sense part configuration; pressure for each segment can be preprogrammed to provide less pressure on the outer edges, or more in the center if desired. The "CSD" computer control will hold a max. of (20) programs.Equipped with: -- Segmented Polishing Platen: Segments are computer controlled to conform to irregular shaped panels; sanding pressure on panel edges is adjustable. -- Platen will accept panel thickness variation up to 5/64" (2 mm). -- Dual speed motor: 26 & 31 kW (35 & 42 HP); abrasive belt speed: 10 + 20 MPS (33 + 66 FPM); abrasive belt size: 2,050 mm x 3,250 mm (80.7" x 128"); pneumatic air tension and tracking control. -- 250 mm Dia. Rotary Panel Cleaning Brush, 5 HP motor, 150 mm Outfeed Rotary Panel Cleaning Brush, and 2 HP motor.Additional Features: -- Vacuum bed assembly to ensure flatness of parts and feeding of small parts. -- Computer control and monitor, light indication of panel movement; electronic abrasive belt tracking.Feed System: -- Variable feed speed from 5 - 15 MPM (16 - 49 FPM); 4 kW (5 HP) feed motor; motorized thickness opening.NOTE: This Sander had a "Brand New" ...$ 17,000 display/control installed shortly before it was taken out of service in 2016. The machine has been in storage since that time.

Heesemann HSM Features:Thickness adjustment of sanding heads from 3 to 160 mm (0.118 to 6.3") -- Constant working height of 880 mm (34.6") -- A constant pass line features 3 mm per second adjustment -- An over-thickness control system -- Emergency stops located at machine infeed and outfeed -- Integrated switch cabinet -- Control for excessive workpiece heightHeesemann's HSM transport conveyor features:Electronic variable speed infeed conveyor drive -- Controllable feed speed by an industrial PC -- A transport belt with ½" diamond profiles and one-piece construction -- Automatic tensioning & trackingPress-on RollerA 50 mm roller at the infeed of the machine to hold down thin and warped workpieces with thefollowing features:Spring loaded and adjustable -- Includes workpiece over-thickness controlHigh Performance Vacuum Hold DownEquipped with a high-performance vacuum hold down system for safe movement of workpiecesshorter than 500 mm (20") in feed direction including integrated ventilator in machine base. Canbe turned on or off via controller or in individual programs. The vacuum blower is a high pressureblower, offering optimal performance with minimal power requirements due to the fandesign, helping provide excellent suction with low power consumption.Emergency StopIndustrial PC, This sander is equipped with a 15" high resolution touch screen / industrial PC and features:High resolution display -- Windows® embedded operating system -- Pendent mounted with adjustable viewing position -- Ethernet connection -- Configured as web address for easy network access -- Automatic on-screen diagnostics -- Metric or English input -- 1000 memory addresses -- Alpha/numeric format -- Password protected -- Digital keypad input -- Workpiece thickness -- Conveyor belt feed speed -- Sanding pressures -- One button startRoller Table For infeed500mm long (20";) -- Height adjustableHead 1: DB-S Head – Rotating Planetary Sanding Unit:10 driven discs with quick changing device -- Rotation in both directions -- Central height adjustment -- 7.5 kW (10 Hp) motor to power the discs -- 1.5 kW (2 Hp) motor gear box -- Brush trimming: Flex Trim -- Tool Diameter: 150 mm (6";) -- Other brush discs available on demand -- One set of discs is included with sanding headHead 2: DB-S Head – Rotating Planetary Sanding Unit:10 driven discs with quick changing device -- Rotation in both directions -- Central height adjustment -- 7.5 kW (10 Hp) motor to power the discs -- 1.5 kW (2 Hp) motor gear box -- Brush trimming: Flex Trim -- Tool Diameter: 150 mm (6";) -- Other brush discs available on demand -- One set of discs is included with sanding head Brush trimming: Flex Trim -- Tool Diameter: 150 mm (6";) -- Other brush discs available on demand -- One set of discs is included with sanding headTechnical Specifications:Working height: 880 mm (36.2") --Workpiece thickness: 3 mm to 160 mm (0.118" to 6.29") --Working width: 1300 mm (51.2") --Transport belt speed: 3 mpm

--AT AUCTION-- HEESEMANN KSA 8 CSD 80" Lacquer/Sealer Sander This is a Very Special "extra wide" HEESEMANN equipped with: HEESEMANN's patented "CSD" selective pressure adjustment system, sensors placed every 5/8" (16 mm) sense part configuration; pressure for each segment can be preprogrammed to provide less pressure on the outer edges, or more in the center if desired. The "CSD" computer control will hold a max. of (20) programs. Equipped with: Segmented Polishing Platen: Segments are computer controlled to conform to irregular shaped panels; sanding pressure on panel edges is adjustable. Platen will accept panel thickness variation up to 5/64" (2 mm). Dual speed motor: 26 & 31 kW (35 & 42 HP); abrasive belt speed: 10 + 20 MPS (33 + 66 FPM); abrasive belt size: 2,050 mm x 3,250 mm (80.7" x 128"); pneumatic air tension and tracking control. 250 mm Dia. Rotary Panel Cleaning Brush, 5 HP motor, 150 mm Outfeed Rotary Panel Cleaning Brush, and 2 HP motor. Additional Features: Vacuum bed assembly to ensure flatness of parts and feeding of small parts. Computer control and monitor, light indication of panel movement; electronic abrasive belt tracking. Feed System: Variable feed speed from 5 - 15 MPM (16 - 49 FPM); 4 kW (5 HP) feed motor; motorized thickness opening. NOTE: This Sander had a "Brand New" ...$ 17,000 display/control installed shortly before it was taken out of service in 2016. The machine has been in storage since that time.

2004 Hymmen Proficoater 60" Roll Coat Line - Model ULX-S: Includes spare drum and lights SCMI Finish Sander

24" x 96" belt with 28" wide opening into oven Dayton gear drive with 1/2 HP DC motor 230 volt UV unit 96" x 42" x 71" overall dimension

IST (Industrial Surface Technologies) - PW 4, ...Industrial Pail Washer.Industrial Pail Washer is designed to wash the interior & exterior of open pails ranging from 1/4 to 5 gallons in size or other types of containers.An optional potholder can be used to hold smaller containers in place during washing. The PW is fully pneumatic, features all explosion proof components, and can be located in Class I, Division I hazardous areas. -- Heavy-Duty PW2 to PW12 solvent washers are made of industrial quality painted steel for durable use and trouble-free. An optional stainless steel finish is available to resist rusting and solvent spillsSpecifications: -- Capacity: (4) x 5 Gallons/19 Liter. -- Pump capacity: 46.2 GPM. -- Air Input: 75-100 PSI. -- Air Consumption: 40 CFM. -- OAL 67" x 45 1/2" x 72 3/8". -- Weight : 650 Lbs.

IST (Industrial Surface Technologies) - AW 80, ...Industrial Washer with vibration.ISTpure's Stir Wash Tanks are designed to clean complex parts with an adjustable stirring platform for up to 100 stirrings per minute.Parts washers by stirring are very effective in thoroughly cleaning the surface and interior cavities of parts or batches of parts of any size.Simply load the parts into the tank through the opening in the top, set the cycle time and agitation speed Specifications: -- Tank capacity: 80 gallons -- Stirring System: Self-cleaning stirring platform with top loading that facilitates loading/unloading operations -- Adjustable Stirring Speed: Ranges from 0 to 100 stirrings per minute -- Pneumatic System: Operates at 120 psi pressure -- Inner tub made entirely of stainless steel components -- Included Attachment: Hand Wash Brush with Continuous Flow -- Standard Pump: Electric Motor -- Fluid Capacity 80 gallons -- Fluid Level 12" 17 1/2" -- Load Capacity 250 lbs 750 lbs --Overall Dimensions (D x W x H) 33" x 51 1/2" x 66 1/2" -- Interior Dimensions (D x W x H) 27 1/4" x 44 1/2" x 28" -- Tub Dimensions (D x W) 17 1/2" x 41 1/2" 27 3/4" X 54" -- Shipping Weight 556 lbs -- Compressed air required 8 cfm@ 120 p

LOEWER DENIBBING SANDER4-Head, 53" width cap., great Denibbing Sander -- The patented conbination of rollers and rotating / oscillating discs makes the Perfection BBDD sanding machiine the ideal finishing solution for entry doors, cabinet doors, drawer fronts, sheet foods, shutters, face frames, furniture and much nore. -- The LOWER DMBBDD sanding machine is sthe ideal soluton for all sanding applications including whitewood, stain and sealer coats(inciuding UV). The work piece first passes under two large counter rotating spiral hubs, then under eleven rotating discs that oscillate from left to right. This provides very uniform edge breading in whitewood sanding and eliminates most (if not all) hand sanding of the sealer coat. -- The patented combination of roller and rotating discs provieds very uniform sanding across the entire work piece, even into deep profiles without loosing detail. -- SPECIFICATIONS OF MACHINE --Thickness of work piece Min: 10mm (1/2")-- Max: 80mm (3") --Feed belt width Max:1350mm (53") --Feed belt motor 1.5 KW (3Hp) 3-15 M/min (10-50 Ft/min) --Top sanding roller 2.2KW (3Hp) 25-300 O/min (RPM) --Disc Rotation 2.2KW (3Hp) 25-300 O/min (RPM) --Disc Osciliatiojn ).37KW (0.5) 10-60 O/min (RPM) --Vacuum motor 7.5KW (10Hp) --Machine weight 1,800 kg -- Aproximate Machine dimensions based on similr machine W:2000mm (6'7")/ L:2780mm (9'2")/ H:6'11")

LOEWER DISC MASTER 3DBB Denibbing Sander with (2) Sanding Stations, 53" Width Capacity:53" Width cap. Denibbing Sander with a patented combination of rollers and rotating/oscillating discs make the LOEWER Discmaster 3DBB Sanding Machine the ideal finishing solution for entry doors, cabinet doors, drawer fronts, sheet goods, shutters, face frames, furniture and much more. -- Ideal solution for all sanding applications including whitewood, stain and sealer coats (including UV). -- Operation: The workpiece first passes under (16) rotating discs with abrasive brush loadings and then under (2) large counter-rotating spiral brush roller type hubs,Head Configuration: -- 1st Unit: (16) Rotating discs 250 mm (10") diameter each with (24) keyways 75 mm (3") long that oscillate from left to right; provides very uniform edge breading in whitewood sanding and eliminates most (if not all) hand sanding of the sealer coat. The discs are variable speed from 50 - 300 RPM by frequency inverter. Eccentric orbital disc movement (patent pending). Separate height adjustment of the disc station to run discs only or brush rollers only or everything together. Digital display to show the height of the discs. -- 2nd Unit: (2) - 400 mm 16" dia. rotating brushes sanding rollers powered by 2.2 kW gear motor with external coolers. -- Variable spindle speed 14 - 300 RPM adjusted by frequency inverter on each spindle and separately adjustable. The first drum rotates with the feed and the second rotates against the feed. Includes a panel blow-off station. -- The patented combination of rollers and rotating discs provides very uniform sanding across the entire workpiece, even into deep profiles without losing detail. Specifications: -- Disc oscillation by 0.37 kW (0.5 HP) motor, (0 - 60 Cycles/Min). -- Min. part thickness 4 mm (3/16") and max. 4"; -- Vacuum bed with 7.5 kW (10 HP) motor; Vacuum blower outlet on side of the machine has 200 mm outlet. -- Variable vacuum bed conveyor feed speed from 3 - 15 m/Min (8 - 50FPM). -- Pneumatic belt centering system. -- Fixed bed height for installation in a line. -- Separate variable speed adjustment for disc & roller. -- Antistatic brush strip device. -- Control panel Left Side-mounted. -- Emergency stop pull cords at both infeed and outfeed. -- Dust extraction outlets 3 x 80 mm (3.2") 4 x 140 mm (5.6") and 1 x 200 mm (8").Equipped with: -- PLC Touch-screen control: Simple & user-friendly "TOUCH SCREEN" PLC control with color monitor; PLC storage capacity for up to (25) individual sanding programs; -- the PLC control interface also allows for easy machine connection to a flat-line, tow-line or hanging-ling finishing system.

ROTOFAST 10 panel cleaner is designed for automatic cleaning of parts just prior to coating application for a dust-free finish. A rotating brush is combined with air blow-off units and an anti-static bar in order to efficiently clean flat or profiled parts of different shapes and dimensions. KEY FEATURES --Top surface One rotating brush with variable speed and height adjustment --One de-ionizing (anti-static) bar --One group of rotary blowers with timed entry --One group of fixed blower nozzles with timed entry Bottom surface --One group of fixed blower nozzles with timed entry --All components housed in single cabinet with suction hoods --Feed speed adjustable by potentiometer --Rubber pressure rollers to secure parts while brushing --Belt conveyorWeight 600 Kg.