Woodworking Equipment For Sale

BIESSE - AKRON 420, ...Edgebander -- Machine Capacity -- Thickness of banding rolls: 0.4 - 3 mm (0.12"); thickness of strips: HPL, veneer, solid wood strips, 0.4 - 6 mm (0.24"); panel thickness: 60 mm (2.4") max. & 10 mm min.; min. panel length: 140 mm (5-1/2"); min. panel width: 85 mm (3.3"). -- Equipped with: -- Feed/Glue Unit: Automatic strip & coil feed magazine with: Robust shear-type; 3 mm PVC guillotine. -- Hot Melt Glue System: 10 Min heat-up time; Teflon coated gluepot; digital thermostats with automatic kickdown when machine is in idle mode. - 1" Dia. glue applicator roller; pressure section with: (1) large dia. "non-stick" coated drive roller & (2) chrome plated idle rollers with pneumatic positioning. -- Workstations --÷ Inclined travel Front & Rear End Trims: 1/4 HP - 12,000 RPM motors; motors travel on (2) straight slides; pneumatic tilt: :0° - 15° on horizontal plane. -- Top & Bottom Fine Trims: 1/2 HP - 12,000 RPM motors; numeric readouts for easy set up. -- Top & Bottom Buffing Station: 1/2 HP - 2,800 RPM motors; units tilt :0° - 30°. -- Feed Speed: 12 MPM (39 FPM); 3 HP feed drive. -- Complete with: Insulated sound enclosure over all trim stations; extendible side panel support rail.

Machine Equipped as follows: NC 410 PC Based Controller Keyboard with Floppy Drive Automatic Strip Feed Magazine Belt Driven Top Pressure Beam Multi-Coiled Infeed Magazine RT63 Pre-Milling Unit SP20 Glue System w/ Pre-Melt Unit Hot Air Gluing system Automatic Infeed Pressure System T45 Front & Rear End Trimming Units w/Tilt RS10 Top & Bottom Rough Trimming Units RF30 Top & Bottom Fine Trimming Units AR10 4 Motor Corner Rounding Trimming Units RB30 Top & Bottom Profile Scraping Units RC10 Top & Bottom Glue Scraping Units SZ30 Top & Bottom Oscillating Buffing Units PH10 Top & Bottom Edge Heaters Specifications: Min. Panel Thickness:....................10mm? Max. Panel Thickness:....................60mm? Height of Edge-Band Material:…..15-65mm? Min. Banding Thickness:.................0.3mm ? Max. Banding Thickness:........ ...... 20mm? Min. Panel Length:...........................150mm? Min. Panel Width:............................ 100mm? Feed Speeds:.................................10-24m./min? Electrics: ......................................... 460-480V 3 Phase

Biesse Akron 440 Edgebander Premill Top & Bottom Trim Corner Round Edge Scrape Glue Scrape Buffing Unit 12-18 m/min Feed Speed All work units are servo controlled

BIESSE AKRON 855 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING):Specifications: -- Material infeed for strips & coiled edge material like PVC, ABS, veneer, and solid wood.0.4 - 3 mm (0.118"), Panel thickness 10-60 MM ( 0.39" - 2.36"), min. panel length 140 mm (5.5") and 85 mm (3.34") min. widthInfeed System Equipped with: -- Independent copying guide pads on each unit with manual adjustment & mechanical digital indicator.Pre-Milling Unit (FI-701) (2) 1.8 kW motors (2.5 HP), 12,000 RPM with Auto-Set device to ensure optimum positioning of the cutters according to the thickness of the panel being machine; -- "VC-710" edge feeding, gluing & pressing unit with automatic edge magazine for strip & coil stock; 3 mm PVC guillotine. -- "TEKNO-GLUE" System, Pre-Melt "QM-701" for quick heating & tank changing with floating & bi-directional glue roller applicator.Pressure Section: (1) Large motorized pressure wheel with clutch, plus (5) idle rollers, independent pneumatic pressure control & digital counters for quick edge thickness changeover.Edgebanding Workstations: -- Double Motor End Trim, tiltable from 0° - 15°, each motor 0.5 kW (0.6 HP) - 12,000 RPM; sliding in a slicing motion on a 45° precision guide bar with oversized bearing blocks. -- Top & Bottom Rough Trim: Top/bottom (2) motors, each 1.8 kW (2.5 HP) 12,000 RPM with superimposed motor position, 0° - 45° tilt capability, straight cutterheads (80 x 25 x 16 mm) w/insert knives; includes pneumatic exclusion from control panel. -- Top & Bottom Fine Trim: Top/bottom (2) motors, each 1.8 kW (2.5 HP) 12,000 RPM with superimposed motor position, 0° - 45° tilt capability, straight cutterheads (80 x 25 x 16 mm) w/insert knives; includes pneumatic exclusion from control panel. -- Multifunction 4-Motor Corner Rounding Unit "CR-202": (4) Motors, each 0.65 kW (0.87 HP) - 12,000 RPM; motors carry out Corner Rounding and Top & Bottom Trimming on panel edge with PVC, ABS, etc. material and wood edgebanding up to 5 mm max. edge thickness. -- Top & Bottom Radius Scraping (PVC): Knives R = 2 mm, with mechanical digital indicators for precision setup, pneumatic exclusion of the unit from the machining line, PVC scrape collection box. -- Top & Bottom Flat Scraper (Glue): self-adjusting with copy wheels & flat insert knives, removing potential excess glue before buffing unit. -- Top & Bottom Oscillating Buffing Station: (2) motors, each 0.37 kW (0.5 HP) - 2,800 RPM. -- Top & Bottom Hot Air Blowers is made by two 2000 W hotair blowers to reactivate the color of PVC/ABS edges after the machining.The air temperature is adjustableFeatures & Feed: -- All cutting & trimming workstations have HF motors and enclosed by padded sound enclosure, top pressure is provided by staggered double-row holddown wheels mounted on ball bearings. -- Feed chain track speed : 10 - 14 - 20 MPM (33 - 46 - 65 FPM). -- Complete with:CNi PC w/Flat, Color "REAL TIME" graphic interface design on 17"; flat screen (TFT) with high resolution. --

BIESSE - ROVER K 1532: CNC Machining Center (ATC & Boring) -- Specifications:"BRIDGE GANTRY" Machine with: Working field in "X" axis 126" (3,200 mm); "Y" axis 61" (1,560 mm); max. material thickness 6" (165 mm). -- Positioning Speed:"X" Axis 279 FPM (85 MPM); "Y" Axis 196 FPM (60 MPM);"Z" axis 65 FPM (20 MPM). -- Worktable(6) "ATS" Panels supports with: (4) Lifting rails for heavy pieces; (4) "ATS" vacuum pods with universal clamping systems on each panel support.BIESSE "Set Up Assist" & digital readouts for pod & rail placement.(2) Independent working areas with: (6) Pneumatic back & center stops; (4) pneumatic side stops; (2) LH & (2) R. with (12) removable nylon clamping units for narrow pieces. -- Boring Unit:4 HP (3 kW) Motor with: Variable speed from: 2,800 - 6,000 RPM."BL 30" Boring head with: (20) "Quick Change" independent vertical spindles; (9) spindles in "X" axis; (11) spindles in "Y" axis.(8) Horizontal boring spindles with: (2 + 2) in "X"'; (2 + 2) in "Y" axis.(2) Grooving Saws: (1) In "X" axis; (1) in "Y" axis for max. 120 mm dia. blade. -- Machining(1) 17.7 HP (13.2 kW) Electrospindle router with: HSK F63 Adaptor; variable speed from 1,000 - 24,000 RPM.Motorized dust deflector shield with: 6-Position adjustable dust suction hood; blowing unit.NOTE: NC Controlled C-Axis for 360° horizontal processing is not installed but CAN BE ADDED. - Per spec sheet on Dropbox folder: "“Prearrangement for the assembly of a 360° operating unit (C axis). It includes all the harness for the electric cabinet. The slot is to be specified. It allows reducing machine downtime for the installation of this unit on an already delivered machine";. (1) 16-Position ATC tool plate mounted on board the "X" axis at the "X" axis carriage (rear of the machine base). -- Operator Interface:PC Front-End with: BIESSE "BH 660" + BIESSE "bSolid" + Windows "7 WRT" Operating System.21-1/2" Flat screen monitor; full standard keyboard & mouse; 8 GB RAM memory;128 SSD GB hard disk or superior; USB Ports for data entry. Dedicated graphics card; Ethernet connection to an office PC with specific function controls & internet trouble shooting capabilities.Electronics are mounted in an air conditioned & dust free environment control cabinet. -- BIESSE "bSolid" is a 2D/3D CAD/CAM software program that supports the performance of any machining operation thanks to vertical modules designed for specific manufacturing processes.Planning with "bSolid" takes just a few clicks & has endless possibilities; "Real-Time" simulation allows the Operator to visualize the piece prior to processing; it provides virtual prototyping of the piece to avoid collisions & ensures optimal machine performance. -- Complete with:(1) 100 cbm/Hr Vacuum Pump; handheld "Remote Control" pendant for immediate Operator control; LED bar with (5) colors that show the machine's status in "Real-Time".Centralized Automatic Lubrication System; Scrap Belt conveyor; Tool Per-setting device; Safety fences; s

BIESSE - ROVER 20: CNC Machining Center (w/ATC/Boring)Specifications: -- Working capacity: X-Axis: 2,885 mm (113.58"); Y-Axis: 898 mm (35.35") for boring; 950 mm (37.40") for routing; max. panel thickness: 65 mm (2.56"). -- Positioning speed: X-Axis: 75 MPM (246 FPM); Y-Axis: 45 MPM (147 FPM); Z-Axis: 15 MPM (49 FPM).Equipped with: -- Work area with (2) Working zones: (6) Manually positioned & pneumatically locked panel supports; each with: (2) 6"; x 6-1/4"; Vacuum pods; (6) backstops/clamps; left & right side stops; all pneumatic raised & lowered automatically by start/stop of machining cycle. -- High precision prismatic guides & ground helical rack on X-axis; hardened ground ball screws on Y- & Z-axes. -- Boring Unit: 1.7 kW (2.3 HP) - 5,135 RPM Motor; spindle speed: 4,000 RPM; (10) vertical independently operated spindles with: (6) In X-Axis & (4) in Y-axis; (6) horizontal spindles with: (2 + 2) In X-Axis & (1 + 1) in Y-axis; (1) grooving saw in X-axis with 120 mm (4.72") dia. blade & blade speed 5,200 RPM. -- Machining: HSD "ES 919A" 6.6 kW (8.9 HP) Air-cooled electrospindle with: ISO 30 Adapter; RH & LH rotation; spindle speeds: 1,000 - 24,000 RPM; 4-position side-mounted automatic tool changer magazine; 3-position rear-mounted on-the-fly automatic tool changer (ATC). -- Control: PC Front-End with: 15" Color display; pendant control; (2) foot pedal controls.Complete with: -- BECKER "PICCHIO 2200" Vacuum Pump: 3 kW - 4 HP - 130 mbar.Control Dimensions: 60" x 36" x 77" H.Vacuum Pump Dimensions: 28 x 14 x 24 H.

Capacity overall cutting length 3200 mm (128"). Cutting height 100 mm saw blade projection. 18 HP main and 3.6 HP scoring motor. Modular roller rear machine table. Side aligning device for squaring ripped strips out to 74". Variable saw carriage travel speed 0-328 FPM. 328 FPM return. Electronically controlled overhead program fence. Rack & pinion driven. Forward speed 196 FPM. Return speed 196 FPM. 6 clamps (open up to 100 mm), of which (2) are closely spaced in crosscut area for strip handling and the other (4) are at equal distance in rip cut area. AC Servo motor drives on both saw carriage and pusher fence. "Gateway" PC controller w` monitor and >assist line> w`LED readout integrated into high tech look operator control panel (displays cutting dimensions & patterns). Data input by keyboard or direct downloading from office PC. Side Crosscut aligner. "Quick Change" saw blade replacement system. (3) front mounted air floatation tables with patented rounded front for moving panel from rip to crosscut position (24" x 79" each).

BIESSE AKRON 855 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING):Specifications: -- Edge & Workpiece Capacity: 0.4 -15 mm (0.016" - 0.59"), Edge thickness, 14 - 65 mm (0.55" - 2.56"), Edge height, 10 - 60 mm (0.39" - 2.36"), Panel thickness:140 mm (5-1/2") Min. panel length, 85 mm (3.3") Min. panel width.Infeed Section: -- Pre-Milling Unit, "FI-701 Rectifies face to be edged before applying glue, Horizontal & vertical movement of (2) motors on linear guides, Independent automatic temporized intervention of (2) 1.8 kW (2-1/2 HP) 12,000 RPM Motors, Independent copying pads on each unit, Auto-set device to ensure optimum positioning of cutters according to the thickness of panel being machined. -- Edge Feeding, Gluing & Pressing Unit, "VC-710": with Automatic edge magazine for strip & coil stock, 3 mm (0.04") PVC Guillotine, "TEKNO-GLUE" System Includes: Pre-Melt, "QM-701", For quick heating & tank changing with floating & bidirectional glue roller applicator, and NC axis idle presser roller movement device. -- Pressure Section: (1) Large driven & (5) Idle rollers, Independent pneumatic pressure control, Programmable servo motor for quick edge thickness changeover, Feed speeds 10, 14 & 20 MPM (33, 46 & 65 FPM).Workstations: -- End (Edge) Trimming Unit, "IN-701-V": (2) 0.35 kW (1/2 HP) 12,000 RPM Motors, Automatic 4-position programmable chamfer from control panel (0°, 3.6°, 11°, 15°), Sliding in slicing motion on 45° precision guide bar with oversized bearing blocks. -- Superimposed Flush (Double Edge) Trimming Unit: "RS-701": Top & bottom, (2) 0.8 kW (1 HP) 12,000 RPM Motors with Superimposed motor position, 1° Tilt capability. Includes: Pneumatic exclusion device & Pneumatic top/bottom motor positioner. -- Tilting Top & Bottom Trimming Unit, "RI-701": (2) 0.65 kW (0.87 HP) 12,000 RPM Motors, For radius top & bottom fine trimming, Unit can be tilted 0° - 45°. Includes: NC axis multiple machining device. -- Corner Rounding Unit, "CR-200V": For corner rounding, top & bottom trimming on panel edge with synthetic material & wood edgebanding up to 5 mm (0.20") Maximum edge thickness. -- Edge Scraping Unit, "RB-701": For finishing rounded-off edges in PVC or ABS up to 5 mm (.20")thickness; Includes: Pneumatic unit lifter. -- Flat (Glue) Scraper, "RCC-700":Top & Bottom, removes potential excess glue before buffing unit. -- Buffing Unit, "SPL-700": Top & bottom. -- Hot Air Blower Unit, "PH-700", (2) STEINEL "2346" 2,000 W, Reactivates color of thick plastic.Complete with: -- PC-based control panel with 15" Color LCD monitor, HF (High-frequency motors on all cutting & trimming workstations. --Top pressure beam programmable via positioning motor, Top pressure provided by belt hold-down. -- 36" Diameter Coil table, Padded sound enclosure. -- Manuals (as pictured). -- Dimensions: 280" x 42" x 72" H. Weight: 3500 kG (7,750 Lbs).

Biesse Akron 1440 PUR Return conveyor available - demo unit!

Biesse Cosmo Case Clamp Bought new, never used

Min. Panel Thickness: 0.39? Max Panel Thickness: 2.36? Height of Edge-Band Material: 0.55-2.51? Min. Banding Thickness: 0.01? Max Banding Thickness: 0.39? Min. Panel Length: 5.51? Min. Panel Width: 1.96? 2 Feed Speeds: 39ft/min & 59ft/min Electrical: 230V, 60Hz, 3Phase Equipped With Siemens TD200

BIESSE STREAM B1 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING), Production Edgebander: -- Specifications: Working cap., 0.4 - 15 mm edge thickness cap., min. panel width 100 mm, panel thickness 10 - 60 mm, min. panel length 150 mm. -- Pre-Milling Unit: With jump control & side copying unit for managing warped panels, 2-position infeed fence, digitals readouts. -- NC 410 Controller with:Graphic interface on MS-Windows 2000 Professional, 32-bit operating system; high resolution LCD color screen, unlimited" number of working programs, each with functions for remote control of processing units; fault diagnostic, bar code reader adaptable; etc. -- Automatic (2) coil vertical feed magazineFor coil material up to 3 mm thickness with automatic changeover. -- Patented Glue Systemw/pre-melt, large separated granular hopper for easy filling & high gluing capacity, with roller applicator (reversible); -- Pressure Section,(1) large driven pressure roller & (6) pneumatic secondary pressure rollers. Workstations: -- End Trimming:Double motor front & rear linear end trimming unit "IT 46" (0.4 HP/0.3 kW - 12,000 RPM motors ea.); pneumatic chamfer setting, 0° - 15° adjustable. -- Pre/Rough Trimming:Top & bottom "RS 10" (1.75 HP/1.3 kW - 12,000 RPM motor ea.), pneumatic exclusion & positioning from control panel. -- Radius/Bevel Trimming:Top & bottom (0.87 HP/0.65 kW - 12,000 RPM motor ea.), tiltable 0° - 30°, pneumatic exclusion from operator panel. -- Corner Rounding:4-Motor for leading & trailing edges. -- Profile Scraping Unit:Top & bottom with collection box. -- Flat Glue Scrapers:Top/bottom to remove potential glue squeeze-out. -- Buffing Unit:Top/bottom, oscillating/tilting "SZ 30" w/pneumatic exclusion control from control panel & 0.67 HP/0.5 KW- 1,400 RPM motors; -- Hot Air Unit:Top/Bottom hot air blowers to reactivate/smooth heavy pvc radius edges. Complete With:&#9679 Motorized top pressure beam with powered V-belt hold-down, electronic positioning by NC controller. &#9679 80 mm wide Heavy Duty feed chain w/rubber pads, &#9679 4 HP feed drive for feed variable speeds of 26 - 78 FPM. &#9679 Pneumatic Pre-set Stop System for most adjustments via the control panel on top & bottom trim, fine trim, and scraper station, &#9679 Electronic frequency inverter, electronic DC brakes on all trim motors. &#9679 Sound cabins for all trim work stations, outboard panel support. -- Actual Model is BIESSE STREAM B1 9.0

BIESSE SKIPPER 100 L CNC MACHINING CENTER (2-HEAD): -- Specifications:Flexible "Top & Bottom" Machining Center that uses an innovative panel handling system. -- Workable part size:"X" axis is 118" (3,000 mm), "Y" axis is 39.4" (1,000 mm), max. part thickness of 2.4" (60 mm).Min. workable part size in "X" axis is 3.5" (90 mm), "Y" axis is 2.7" (70 mm), "Z" axis is .3" (8 mm). -- Worktable:Automatic LH infeed transfer conveyor with belts & rollers, Automatic RH outfeed transfer conveyor with belts & rollers; infeed/outfeed table is "robot ready". -- Positioning Speed:"X" Axis is 394 FPM (120 MPM), "Y" axis 295 FPM (MPM), "Z" axis is 98 FPM (30 MPM). -- Boring units: (1) Top mounted boring block, 4.2 HP (3 kW), 4,000 RPM; (29) vertical spindles, (17) spindles in "X" axis & (12) spindles in "Y" axis; -- (10) Horizontal spindles, (4+4) spindles in "X" axis & (1+1) horizontal spindles in "Y" axis; -- (1) "X" axis grooving saw with 2.2 HP (1.7 kW) motor - 5,000 RPM, 150 mm dia blade. -- (1) Bottom mounted boring block, 4.2 HP (3 kW), 4,000 RPM, (29) vertical spindles, (17) spindles in "X" axis & (12) spindles in "Y" axis; -- (10) Horizontal spindles, (4+4) spindles in "X" axis & (1+1) horizontal spindles in "Y" axis; -- (1) "X" axis grooving saw with 2.2 HP (1.7 kW) motor - 5,000 RPM, 150 mm dia blade. -- Machining:(1) Top mounted 4.8 HP (3.5 kW) electro spindle, 7,000 - 18,000 RPM with RH/LH rotation; HSK D-50 adaptors for manual push button "quick-tool" change, ERC-32 tool holders & RC-32 collets. -- (1) Bottom mounted 4.8 HP (3.5 kW) electro spindle, 7,000 - 18,000 RPM with RH/LH rotation; HSK D-50 adaptors for manual push button "quick-tool" change, ERC-32 tool holders & RC-32 collets. -- Operator Interface: PC Front-End with BIESSE "NC 1000" + Windows "Biesse Work" Operating System; 15" color monitor; international keyboard with soft-touch keypad & industrial mouse.RS-232 serial ports for possible down-loading from an office PC, USB ports; (1) 48x CD ROM drive; all mounted in a separate control console with a built-in 1,500 W air conditioner for constant temperature & dust-free environment. -- Complete with:Universal transformer for voltages from 200 - 600 volts, 50/60 Hz, 3-Phase; automatic lubrication system for guides & ways; sound enclosure and complete set of safety fences/devices; machine docs & manuals. -- Options include:"BiesseWORKS Advanced" Office version with: (2) Hardware keys; pneumatic part clamping with motorized infeed & outfeed transfer conveyors; Software Disclaimer: EX-FACTORY INC. Offers NO warranty or support, written or implied concerning any/all "optional" or "additional" manufacturer or 3rd party software supplied with this machine. All software related issues including relicensing fees/requirements/functionality & training is ultimately the sole responsibility of the "Buyer".Note : Tear down and loading not included

Biesse Akron 245 Edgebander System is still under power until approx mid-October 2024. Touch PLC will need to be replaced. Everything else is working good on the machine. Owner has had it serviced by Biesse.

Manufacturer Specs premill hot glue end trim top/bottom trim corner rounding scraping buffing Computer interface

BIESSE ROVER C 6.65 CONF 3 CNC MACHINING CENTER (5-AXIS PROCESSING): -- Specifications: Working Capacity: "X" Axis 253" (6,450 mm); "Y" axis 60.4" (1,535 mm); "Z" axis stroke 25-1/2" (650 mm); max. material thickness 10.8" (275 mm). -- Positioning Speed:"X" & "Y" Axes 328 FPM (100 MPM) each; "Z" axis 98 FPM (30 MPM). -- Worktable:(10) EPS (Electronic Positioning System) Panel supports with: (8) Lifting bars; (4) ATS vacuum pods with universal clamping systems per panel support.(2) Independent working areas with: (10) Pneumatic back stops, (2) pneumatic side stops & (2) pneumatic central stops. -- Boring Unit:4 HP (3 kW) Motor with variable speed from 1,500 - 7,500 RPM; (5) independent vertical spindles in "Y" axis.(4) Horizontal boring spindles with: (1 + 1) in "X" axis & (1 + 1) in "Y" axis. -- Machining:(1) 16 HP (12 kW) Liquid Cooled 5-AXIS electro spindle router with HSK F63 adaptor; variable speed from 3,000 - 24,000 RPM.(1) 33-Position ATC tool rack chain located at the back of the machine. -- Operator & Machine Control:PC Front-End with BIESSE "NC 1000" + "BiesseWORKS" + WINDOWS "XP" Operating System.15" Color CRT, full keyboard, mouse, 1.44 MB & CD ROM disk drives. RS 232 & USB ports.Ethernet connection, specific function controls, & and Internet trouble shooting capabilities.Air-conditioned control cabinet & dust free environment."BiesseWORKS" is a multitask Operating System with: Input/output modules, axes override, (4) axes interpolation, diagnostic graphics aid for programming, machine data & tool management. -- Complete with:(1) 250 m³/Hr Vacuum Pump; safety fences & mats; scrap conveyor; CE mark; original documentation; user & maintenance manuals, wiring diagrams & operation of Numerical Control. -- Actual Model is BIESSE - ROVER C 6.65 CONF 3.

BIESSE AKRON 440 AX EDGEBANDER (W/PRE-MILL & CORNER ROUNDING: -- Specifications: Material infeed for strips & coiled edge material like PVC, ABS, veneer, and solid wood. -- Edge & Workpiece Capacity: 0.4 - 3 mm (0.016 - 0.12") Edge; 10 - 60 mm (0.39 - 2.36") panel thickness; 140 mm (5-1/2") min. panel length, and 85 mm (3.3") min. width. -- Working Units:Pre-milling Station: (2) 3 kW (4 HP) - 150 Hz, 9,000 RPM Motors; equipped with panel blow off device and SIKO digital counters for adjustments. -- EVA Gluing Unit: Edge Feeding & Pressing Unit; automatic loading of tape in rolls and strips; quick-change glue pot system. -- Pressure Section: (1) Large 150 mm dia. driven & (5) idle pressure rollers. -- Feed Speeds: Operating feed speeds 12 & 18 MPM (39 & 60 FPM). -- Workstations: Double Motor End Trim; tiltable from 0° - 15°; each motor 0.8 kW (1 HP) - 12,000 RPM; sliding in a slicing motion on a 45° precision guide bar with oversized bearing blocks. -- Top & Bottom Trimming: (2) Motors 0.65 kW (0.87 HP) each; "Pro-Nesting" copiers; cutters R=2 mm. -- Fine Trim/Corner Rounding Unit: (2) Motors; each 0.65 kW (0.87 HP) - 12,000 RPM; motors carry out Corner Rounding and Top & Bottom Trimming on panel edge with PVC, ABS, etc. material, and wood edge banding up to 3 mm max. edge thickness. -- Top & Bottom Flat Glue Scrapper: To remove potential glue squeeze out. -- Buffing Station: Top & Bottom, (2) motors, each 0.37 kW (0.5 HP) - 2,800 RPM. -- Operator Interface:Operator Control Panel, "HDI" High-Definition touchscreen control, Windows XP based. -- User-friendly graphic user interface with diagnostic and assisted maintenance. -- USB and Ethernet port; 1.44 MB floppy drive, automatic or manual startup. -- Complete with:High frequency motors (200 HZ): Padded sound enclosure. -- Top pressure beam with staggered double-row hold-down wheels mounted on ball bearings. -- Actual Model is: BIESSE AKRON 440 AX

BIESSE STREAM A 6.0 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING) (aka "TAPE ROCKET") + NC Axis PackageFeatures: -- "NC Axis Package": The machine adapts to the process being executed based on the edge's thickness and material.Machine management ...100% touch with no need for external devices. - Intelligent language management.Easy program management and usability with rapid transition from one machining operation to the next. Specifications: -- Edgebanding Capacity: Edge thickness for strips: Min./max. 0.4 - 22 mm (0.02" - 0.87"); coiled material from 0.4 - 3 mm (0.02 - 0.12").Panel thickness from: 10 - 60 mm (0.39 - 2.36"); workpiece width: Min. of 85 mm (3.34"); workpiece length: min. 140 mm (5.51").Feed speeds of: 12 - 18 - 20 - 25 MPM (39 - 59 - 65 - 82 FPM).Machine Infeed Configuration: -- Pre-milling Station:(2) 1.8 kW (2.4 HP) - 12,000 RPM Motors; LH & RH Counter Rotating Spindles; NC (Servo) controlled with automatic intervention that guarantees a perfect base for gluing. -- Anti-Adhesive:Automatic Spray Unit with: Glue release agent preventing glue from adhering to work piece's surfaces. -- Infrared Heating Lamp:Preheating workpiece edge to ensure best possible surface adhesion quality of edgebanding material. -- Edge Magazine: Automatic 2-coil/position magazine for processing coiled & strip edgebanding material in real-time. -- Pressure Section:Servo Controlled programmable pressure section with: (1) Large driven roller and (4) idle rollers.Gluing System w/Premelter: -- EVA (Hot Melt), quick premelting granulate with: Glue roller applicator to cover conventional edgebanding material. Workstations: -- End Trimming: Front & Rear Linear end trimmer with: Tilt Function for high speeds with (2) 0.8 kW (1.0 HP) - 12,000 RPM motors. The machine axis movement on linear tracks allows the achievement of very high processing speeds.The copying & tracing system guarantees optimal finish quality; also on high gloss edges with film. -- Flush/Bevel Trimming Unit:Top & Bottom flush or bevel trims with: (2) "Quick Change" 0.65 kW (0.8 HP) - 12,000 RPM motors. -- Fine Trimming Unit: (2) 0.65 kW (0.8 HP) - 12,000 RPM Motors; (2) Servo motors for tool positioning (one for horizontal tool position, one for up/down tool position).Prepositioning of motors by pneumatic air cylinders while using a combination bevel/radius/flush insert knives.Absolute machining flexibility thanks to the full adjustment of the machine according to the required edge thickness. -- Corner Rounding Unit: (2) 0.65 kW (0.8 HP) - 12,000 RPM Motors for front/back corner and upper & lower edge profiling.The controlled axis on the Corner Rounding unit supports the management of infinite machining settings. -- Profile Scraping Unit:Top/Bottom 2-axis NC programmable knife positioning (i.e. 2 - 3 mm radius) for PVC edges. -- Glue Scraping Unit: Flat, top/bottom, digital positioning indicators, pneumatically controlled for in/out position. -- Buffing Station: Top & Bottom buffing

BIESSE AKRON 855 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING):Specifications: -- Material infeed for strips & coiled edge material like PVC, ABS, veneer, and solid wood.0.4 - 3 mm (0.118"), Panel thickness 10-60 MM ( 0.39" - 2.36"), min. panel length 140 mm (5.5") and 85 mm (3.34") min. widthInfeed System Equipped with: -- Independent copying guide pads on each unit with manual adjustment & mechanical digital indicator.Pre-Milling Unit (FI-701) (2) 1.8 kW motors (2.5 HP), 12,000 RPM with Auto-Set device to ensure optimum positioning of the cutters according to the thickness of the panel being machine; -- "VC-710" edge feeding, gluing & pressing unit with automatic edge magazine for strip & coil stock; 3 mm PVC guillotine. -- "TEKNO-GLUE" System, Pre-Melt "QM-701" for quick heating & tank changing with floating & bi-directional glue roller applicator.Pressure Section: (1) Large motorized pressure wheel with clutch, plus (5) idle rollers, independent pneumatic pressure control & digital counters for quick edge thickness changeover.Edgebanding Workstations: -- Double Motor End Trim, tiltable from 0ø - 15ø, each motor 0.5 kW (0.6 HP) - 12,000 RPM; sliding in a slicing motion on a 45ø precision guide bar with oversized bearing blocks. -- Top & Bottom Rough Trim: Top/bottom (2) motors, each 1.8 kW (2.5 HP) 12,000 RPM with superimposed motor position, 0ø - 45ø tilt capability, straight cutterheads (80 x 25 x 16 mm) w/insert knives; includes pneumatic exclusion from control panel. -- Top & Bottom Fine Trim: Top/bottom (2) motors, each 1.8 kW (2.5 HP) 12,000 RPM with superimposed motor position, 0ø - 45ø tilt capability, straight cutterheads (80 x 25 x 16 mm) w/insert knives; includes pneumatic exclusion from control panel. -- Multifunction 4-Motor Corner Rounding Unit "CR-202": (4) Motors, each 0.65 kW (0.87 HP) - 12,000 RPM; motors carry out Corner Rounding and Top & Bottom Trimming on panel edge with PVC, ABS, etc. material and wood edgebanding up to 5 mm max. edge thickness. --Top & Bottom Radius Scraping (PVC): Knives R = 2 mm, with mechanical digital indicators for precision setup, pneumatic exclusion of the unit from the machining line, PVC scrape collection box. -- Top & Bottom Flat Scraper (Glue): self-adjusting with copy wheels & flat insert knives, removing potential excess glue before buffing unit. -- Top & Bottom Oscillating Buffing Station: (2) motors, each 0.37 kW (0.5 HP) - 2,800 RPM. -- Top & Bottom Hot Air Blowers is made by two 2000 W hotair blowers to reactivate the color of PVC/ABS edges after the machining.The air temperature is adjustableFeatures & Feed: -- All cutting & trimming workstations have HF motors and enclosed by padded sound enclosure, top pressure is provided by staggered double-row holddown wheels mounted on ball bearings. -- Feed chain track speed : 10 - 14 - 20 MPM (33 - 46 - 65 FPM). -- Complete with:CNi PC w/Flat, Color "REAL TIME" graphic interface design on 17"; flat screen (TFT) with high resolution. --

BIESSE AKRON 855 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING):Specifications: -- Material infeed for strips & coiled edge material like PVC, ABS, veneer, and solid wood.0.4 - 19 mm (0.118" - 0.75"), Panel thickness 10-60 MM (0.39" - 2.36"), min. panel length 140 mm (5.5") and 85 mm (3.34") min. widthInfeed System Equipped with: -- Independent units on each unit with manual adjustment & mechanical digital indicator.Pre-Milling Unit: (2) 1.8 kW motors (2.5 HP), 12,000 RPM with NC controlled Auto-Set devices to ensure optimum positioning of the cutters according to the thickness of the panel being machine; -- Edge feeding: Gluing & pressing unit with automatic edge magazine for strip & coil stock; 3 mm PVC guillotine. -- "TEKNO-GLUE" System, Pre-Melt for quick heating & tank changing with floating & bi-directional glue roller applicator. -- Pressure Section: (1) Large motorized pressure wheel with clutch, plus (5) idle rollers, independent pneumatic pressure control & digital counters for quick edge thickness changeover.Edgebanding Workstations: -- Double Motor End Trim, tiltable from 0ø - 15ø, each motor 0.5 kW (0.6 HP) - 12,000 RPM; sliding in a slicing motion on a 45ø precision guide bar with oversized bearing blocks. -- Top & Bottom Rough Trim: Top/bottom (2) motors, each 1.8 kW (2.5 HP) 12,000 RPM with superimposed motor position, 0° - 45° tilt capability, straight cutterheads (80 x 25 x 16 mm) w/insert knives; includes pneumatic exclusion from control panel. -- Top & Bottom Fine Trim: Top/bottom (2) motors, each 1.8 kW (2.5 HP) 12,000 RPM with superimposed motor position, 0ø - 45ø tilt capability, straight cutterheads (80 x 25 x 16 mm) w/insert knives; includes pneumatic exclusion from control panel. -- Multifunction 4-Motor Corner Rounding Unit: (4) Motors, each 0.65 kW (0.87 HP) - 12,000 RPM; motors carry out Corner Rounding and Top & Bottom Trimming on panel edge with PVC, ABS, etc. material and wood edgebanding up to 5 mm max. edge thickness. --Top & Bottom Radius Scraping (PVC): Knives R = 2 mm, with mechanical digital indicators for precision setup, pneumatic exclusion of the unit from the machining line, PVC scrape collection box. -- Top & Bottom Flat Scraper (Glue): self-adjusting with copy wheels & flat insert knives, removing potential excess glue before buffing unit. -- Top & Bottom Oscillating Buffing Station: (2) motors, each 0.37 kW (0.5 HP) - 2,800 RPM.Features & Feed: -- All cutting & trimming workstations have HF motors and are enclosed by a padded sound enclosure, top pressure is provided by staggered double-row hold-down wheels mounted on ball bearings. -- Feed chain track speed: 10 - 14 - 20 MPM (33 - 46 - 65 FPM). -- Complete with:CNi PC w/Flat, Color "REAL TIME" graphic interface design on 17"; flat screen (TFT) with high resolution.Actual model is BIESSE AKRON 855