Glue Equipment For Sale

BLACK BROTHERS - 22-D-875-32, ...Top and Bottom Glue Spreader.Capacity 32" Working width. -- 8-3/4" Dia. Rubber roll -- 6-1/2" Dia. chromed steel doctor rolls. -- Top elevator opening w/Readout -- Constant pass line: 36-3/4" -- Outfeed roller conveyor -- 7.5 HP MotorComplete with:1 Spare rollerNOTE: Machine is currently wired for 220v

BLACK BROTHERS 22-D-875-74, Wide Format (74") Top & Bottom Glue Spreader74" Working width, 8-3/4" dia. grooved rubber covered applicator rolls, 6-1/4" chrome plated doctor rolls -- Complete with: Push button magnetic starter, safety guards, and safety reversing bar. -- Top elevator style glue spreader, constant pass line --Main Motor 1HP, 3ph --Feed speed 88FPM --Thickness adjustment via manual hand crank

BLACK BROTHERS 22-D-875-74, Wide Format (74") Top & Bottom Glue Spreader74" Working width, 8-3/4" dia. Grooved rubber covered applicator rolls, 6-1/4" hard rubber covered doctor rolls --Main motor 1.5hp -- Bottom roll adjustment -- Complete with: Push button magnetic starter, safety guards, and safety reversing bar.NOTE: Currently wired for 460v

BLACK BROTHERS Model 22-D-775-68 Top and Bottom Glue Spreader, with 68" working width.This 2007 Black Brothers 775 Top & Bottom 68″ Glue Spreader is powered by a Toshiba 3 HP motor. The feed speed is variable via a VFD hence it is using a Toshiba motor. The doctor rolls are in good plus condition as well as the top applicator roll. The lower roll has grooves at either end BUT 61″ between these grooves as it was feeding 61″ wide material. There is also a glue pump mounted under the controls. It does have (2) valves to control the glue levels for each roll but would require (2) fiber optics elements to be replaced to get the auto level feature to work. -- 3 HP variable speed drive. -- 7-3/4 in. diameter Smooth Applicator Rollers, 6-7/8 in. diameter Chrome Doctor Rollers. -- Upper elevator design for up to 4.5 in. of thickness. -- Readout on roll opening, and equipped with all safety guards. -- For operation on 480V, 3PHIncludes - (1) direct replacement Applicator Roller to what is currently on the machine, along with (2) other replacement Applicator Rollers in near mint condition in varying durometers and material to what is on the machine. (as shown in the photos), and Owner's Manual.

156" long x 60" wide x 80" high (3) vertical pneumatic Clamping bars (7) clamps that can be placed horizontal or vertical on perforated surface

DEPENDABLE - 203, ...Cold Press40" x 102" Cap., side loading on 102" sideSpecifications: &#9679 (3) Split upper platens: 34" wide x 40" deep; split platens can be interlocked for single platen operation. &#9679 45" Max. daylight opening with 12" down stroke hydraulic cylinders. &#9679 (6) Rows of pop-up rollers in machine bed for loading & unloading. &#9679 (3) 7-3/4" Dia. hydraulic press cylinders from the top; (1) per platen. &#9679 Hydraulic power pack with 10 HP motor mounted on floor at end of Press.

DOUCET CLAMP CARRIER 30 SECT X 8 FT 6 IN WIDE (200+) 36" CLAMPS MODEL SRH-1 SX30- 8.5-240-36 SN 87-10-28 Includes: HYD PWR PACK, PANEL FLATTENER Dismantled and ready to load!

Doucet Clamp Carrier Model SRH-40-8.5-240-36 40 Section Clamp 8.5' Wide (240) 2-1/2" x 36" Clamps - Rapid Change Voltage: 480/3/60

- 16.5' long - 16 rotating arms and a total of 288 - 32" clamps

Good Condition 3 phase .5 HP motor

"NEW" Doucet RC - STOCK Gluer - Table top unit for glue applications on a smaller scale. Motorized stainless steel roller equipped with a 2 Litre capacity reservoir easily removable for clean up. -- Spread roller: Stainless steel with roller dimension 8" X 3 1/2"; speed of roller 50 FPM. -- Table top dimension: 20-1/2" x 13".

Maximum Assembled Product Size: 37.5” x 98” Minimum Assembled Product Size: 11.375” (vertical) x 9.75” (horizontal) with spacer blocks 7.5” (vertical) x 5.5” (horizontal) Maximum Framing Width: 4” Minimum Framing Width: 1.5” Tubular Steel Frame THK Linear Bearings and Rails (1) Allen Bradley Compact Logix PAC (4) Allen Bradley Kinetix Servos and Drives a. (1) Vertical Beam b. (1) Horizontal Beam (2) On the Upper Right Hand Clamp to ensure that uniform pressure can be applied regardless of the cut accuracy of the frame parts (1) Hoffman Upright Enclosure Allen Bradley Control Components (Push Buttons, Relays, Power Supplies, Buzzer, etc.) (1) Hoffman Air Conditioner for Electrical Enclosure EMS Press Control/Server Communication Software Package (4) Tregarne Woodwelder with Production Gun

GANNOMAT INDEX 280 TREND CNC BORE, GLUE & DOWEL INSERTER: -- Specifications:CNC Controlled horizontal Point-to-Point Drilling, Gluing & Dowel Inserting Work Center for absolute, incremental, variable (parametric) programming of boring patterns. -- Working Field(4) Independent zones for individual processing of (1 - 4) pieces. Pneumatically activated Stop system (side fences) consisting of: Right-hand, left-hand, and center stop. Max. single part Length 2,800 mm (110"). As a 2-zone: LH & RH is 1,400 mm (55") each part. As a 4-zone with center fence: LH/RH is 700 mm (27.5") each part.Min/Max. Material Thickness 0.50" - 3.125" "X" Axis Positioning Speed 246 FPM (75 MPM) and driven by rack & pinion for fast acceleration/deceleration of working unit. "Y" Axis is set by mechanical digital counters. "Z" Axis is NC controlled height adjustment for boring/inserting units. -- Hold-down Clamps:Total of (10) pneumatic, "quick change" Hold-down Clamps. -- Dowel driving & horizontal boring:Integrated into (1) station; the Dowel Driving Unit is located alongside the Boring Station; both units are mounted on (1) support. -- Horizontal Drilling Spindle:Can be setup for 6 - 8 or 10 mm; dowel length from 25 - 50 mm. -- Doweling Station includes:Vibrating hopper with: (1) Single drop device and (1) outlet tube; insertion head & dowel driving with air impulse.Mechanical dowel diameter & dowel length control prevents the insertion of any oversized dowels. -- Glue Valve/Amount:Controlled via software and can be adjusted by milliseconds; (2) standard separate stainless steel 1.5 gal. pressurized tanks (one for glue, one for water to clean/purge the glue tubes. -- Operator Interface:GANNOMAT + BECKHOFF "C3640 Twincat" PLC Operating System.15" Touch-Screen color monitor; network card (for online operation); serial, parallel, USB ports. -- Actual model is: GANNOMAT INDEX 280 TREND. NOTE: Machine is currently setup for 8 mm dia. x 35 mm long dowels.

GANNOMAT INDEX 130 LOGIC CNC BORE, GLUE & DOWEL INSERTER (W/Top Drilling Option): -- Specifications:The GANNOMAT "INDEX LOGIC" is a CNC Controlled Point-to-Point Drilling/Gluing/Dowel Insertion Machine for variable programming of boring patterns. -- "X" & "Y" Axis set by manual digital indicators; "Z" Axis adjusted via CNC controlled Servo drive. -- Working width:1,300 mm (51") x 3/4" - 7-3/4" Width x 1/2" - 3-1/8" material thickness with (2) field, LH/RH (mirror-image). - Table size: 4-1/2" x 52-3/4" x 35" H with 9" x 52" extension. -- (6) Vertical hold-down cylinders for horizontal part processing. -- Dowel Driving & Horizontal Boring: Integrated into (1) station; the dowel driving unit is located alongside the boring station; both units are mounted on (1) support. -- Horizontal Drilling & Boring Station: Head can be setup for 6 - 8 or 10 mm, dowel length from 25 - 50 mm (currently set up for 8 mm dia. x 50 mm long dowels). -- Doweling Station: Vibrating hopper; insertion head & dowel driving with air impulse; glue valves are controlled individually at the control cabinet; central adjustment for the amount of glue by means of a digital timer. -- Operator Interface: MS-XP & GANNOMAT Production software; 15" color touchscreen monitor interface; USB drive; bar code capable. -- Controller & Drive: BECKHOFF "C3620 TWINCAT V2.10". -- Complete with: (1) Glue tank; (1) water tank; auto lubrication system, and all original manufacturer's machine documentation. -- Included Options: An optional Single Spindle top drilling spindle with a Z-axis control. Barcode Scanner easily retrieves prewritten stored programs in an instant. -- Actual Model is: GANNOMAT INDEX 130 LOGIC.

Laminating Rolls: 61" (155 cm) roll face with thermally conductive high release silicone surface; upper and lower main rolls internally heated; temperature controlled by state-of-the-art infrared sensors and digital PID controllers Laminating Opening: 1.5" (3.8 cm) maximum opening controlled with dual air cylinders. Laminating Material Uses heat activated and pressure-sensitive materials 0 - 55" (0 - 140 cm) wide on a 3" (7.6 cm) ID core Laminating Speeds 0 to 14.5 fmp (0 to 4.5 mpm) Post Lamination: Fanless cooling system provides uniform, filtered air for thermal shock without exposure to dangerous fan blades. Vinyl Transfer Complete roll to roll transfer, lamination, and edge trimming in one pass Safety Features • Two emitter-receiver photoelectric systems protect rolls from damage. • Emergency kick cables front and rear. • All electrical and moving mechanical parts are located in bolted cabinets • Four emergency stop buttons Installation Requirement 220 to 240 VAC, 50/60 Hz, 55A. 32 A per phase. Air: 2 cfm at 100 psi, minimum(0.5 m3 at 700 vPa)

HOFER HOP 160 K Hydraulic Door/Veneer Heavy Duty Cold PressSpecifications:Platen size 63" deep x 98" long, Total Daylight/Opening 32".available. Currently set at about 13" opening. Top platen is hydraulically powered by a 2.2 KW power pack. and has (10 sets) of bolt holes for manual adjustment of daylight opening.Equipped with:(8) 3-1/4" Diameter Hydraulic cylinders, Rack & pinion platen leveling adjustment.Front and back loading (access on all sides).Heavy duty steel structural beams. Bolted top and bottom platens.Features:Pneumatically loaded 3 +1 rows of idle rollers on bottom platen for ease of feeding the load in and out front of press. Air valve for up/down selection of bottom platen rollers.Hydraulic closing speed adjustment.Electrical controls on right hand side.Dimensions/Weight: 124" x 72" x 122" H. Approx. 12,000 Lbs.

HOMAG (OPTIMAT ABD060/12/D/NA) CNC BORE, GLUE & DOWEL INSERTER: -- Specifications: Horizontal drilling block/fixture with (3) 10 mm (0.39") Dia. Individually selectable 7,500 RPM spindles & 1.73 kW (2.32 HP) 3,420 RPM Motor, Max. drilling dia. 20 mm (0.79"), Total drill bit length 70 mm (2.76"). -- Low-viscosity glue injection system with DÜRR SYSTEMS “EcoPump AD"; Low-pressure double membrane glue pump & External flow sensor, Max. viscosity 700 mPas. -- MAFU “MRA 250"; Vibrating hopper dowel feeder. -- Working Capacity:Workpiece length 20 - 1,250 mm (0.79" - 49.2"), Workpiece width 50 - 800 mm (1.97" - 31.5"), Workpiece thickness 10 - 60 mm (0.39" - 2.36"). -- Dowel sizes 8 mm Dia. x 30 mm or 35 mm L (0.31" Dia. x 1.18" or 1.38" L). -- Work Area: Overall table size 20" x 150" with (2) Separate work fields to process up to (4) work pieces independently, Work pieces can be loaded in one field while being processed in the other field. -- Pneumatically lowering left-hand, right-hand & center stops, Distance between left-hand & right-hand stops 1,270 mm (50"), Distance between center & left/right-hand stops 620 mm (24.4"). -- Operator & Machine Control: "POWERTOUCH" 3-Axis Control with USB Port, 10/100 Ethernet Port & 21" TFT Flat screen monitor. -- WOODWOP, ABDWORK with BECKHOFF TWINCAT, MMR Data collection & Analysis, SCHULER machine data acquisition, Tapio-ready. -- Complete with:(4) 3-1/8"; x 5-1/8"; Pneumatic clamping cylinders. -- Glue nozzle cleaning system. -- HONEYWELL “HYPERION 1300G"; Barcode Scanner, with Supported barcodes: 1D – Barcode & 2D – Data matrix code.

HYDREX HPX410-5 Hot Press 160 Tons using (8) hydraulic cylinders, Five daylight openings. Suitable for laminating veneer panels/doors, decorative paper, fireproof board, etc.Features (Overall): -- Board size up to nominal 4' x 10' (about 51" x 126"). -- Front Controls for easy setup & operating configuration, incl. temperatures and cycle time , emergency pedal, quad temperature protection device. -- (8) Cylinders (upstroke) -- 160 Tons of overall pressure, -- Recirculating Thermal Oil heated with package heaters housed in a boiler tank.Detailed Specs: -- Platen size 1300 mm x 3200 mm (51" x 126") approx. Thermal Oil heated Hot Press with drilled steel platens, 1.5" thick; -- (8) Hydraulic "upstroke cylinders", approx. 85 mm dia.; rack & Pinion guide system for parallel closing of the platens. -- 40 PSI specific pressure over the entire platen area; 54 kW heating power. Approx. 7.5 kW (10 HP) hydraulic pump motor. -- 1.5 kW (2 HP) Hot Oil circulation pump; approx. 120° C (248° F) max. operating temperature. -- Max Working height is 4"; Loading from (3) sides; 39-1/2" from floor with lower platen in the down position; Heavy I-beam welded steel frame construction. -- "Safety" emergency Stop Cable around the operating sides of the machine, and E-STOP mounted on the control panel. -- Overall press weight is approx. 27.500 Lbs. -- Optional: Extra Large Oil Heating Tank for Special Higher Temperatures if needed.

HYDREX HPX510-5 Hot Press 120 Tons with (5) Daylight openings. Suitable for laminating veneer panels/doors, decorative paper, fireproof board, etc.Features (Overall): -- Board size up to 5' x 10', -- Front Controls for easy setup & operating configuration, incl. temperatures and cycle time, emergency pedal, and quad temperature protection device. -- (8) Cylinders (upstroke) -- 120 Tons of overall pressure, -- Recirculating Thermal Oil heated with package heaters housed in a boiler tank.Detailed Specs: -- 122" x 61" Thermal Oil heated Hot Press with drilled steel platens, 1.5" thick; -- (8) Hydraulic "upstroke cylinders", approx. 85 mm dia.; Rack & Pinion guide system for parallel closing of the platens. -- 120 Ton total pressure; 54 kW of heating power. 40 PSI specific pressure over the entire platen area; 4.5 kW (6 HP) hydraulic pump motor. -- 1.5 kW (2 HP) Hot Oil circulation pump; approx. 120° C (248° F) max. operating temperature. -- Max Working height is 4"; Loading from (3) sides; 39-1/2" from the floor with lower platen in the down position: heavy I-beam welded steel frame construction. -- "Safety" emergency Stop Cable around the operating sides of the machine, and E-STOP mounted on the control panel. -- Features: "Last" (2) cylinders can be turned off to press shorter panels. - Overall press weight is approx. 24,000 Lbs. -- Overall dimensions: 3,800 length (+610mm -boiler + 610mm -pump/tank) x 1,790 wide x 2,450 mm high.

HYDREX HPX48-1 Hot Press, Single daylight opening. Suitable for laminating veneer panels/doors, decorative paper, fireproof board, etc.Features (Overall): -- Board size up to 4' x 8', -- Front Controls for easy setup & operating configuration, incl. temperatures and cycle time, emergency pedal, and quad temperature protection device. -- (6) Cylinders (upstroke) -- 80 Tons of overall pressure, -- Recirculating Thermal Oil heated with package heaters housed in a boiler tank.Detailed Specs: -- 98" x 51" Thermal Oil heated Hot Press with drilled steel platens, 1.5" thick, 4" Max Working height.. -- (6) Hydraulic "upstroke cylinders", 85 mm dia.; rack & Pinion guide system for parallel closing of the platens. -- 80 Ton total pressure, 40 PSI specific pressure over the entire platen area; 4 KW (5.5 HP) hydraulic pump motor. Platen moving speed 5 FPM -- 1.5 kW (2 HP) Hot Oil circulation pump; approx. 120° C (248° F) max. operating temperature. -- Loading from (3) sides; 39-1/2" from the floor with lower platen in the down position: heavy I-beam welded steel frame construction. -- "Safety" emergency Stop Cable around the operating sides of the machine, and E-STOP mounted on the control panel. -- Overall press weight is approx. 12,500 Lbs). Overall dimensions 129" x 65" x 102" high.Also available with (3) openings - 100 Tons and (5) openings - 100 Tons.