Woodworking Equipment For Sale

TIMESAVERS 237-4IC Four-Head Wide Belt Sander37" Width cap. Drum, Drum, Drum, PlatenHead Configuration:1st Head: Rubber covered contact roll, 9-1/2" dia., 30 HP motor;2nd Head: Rubber covered contact roll, 9-1/2 " dia., 25 HP Motor. 3rd Head: 9-1/2" Grooved Rubber Covered Contact Drum With A 20 HP Motor4th Head: Finishing platen, 2-1/2" wide, 20 HP motorSpecification -- 37" x 75" abrasive belts with Pneumatic tracking. -- Motorized part thickness adjustment, height, 0" - 6" opening. -- Automatic part thickness adjustment, -- Infeed & outfeed spring loaded holddown shoes, -- Variable feed speed from 15 - 45 FPM, 5 HP motor. -- Pneumatic feed beltEquipped with & Features: -- Motor load meters, -- Infeed emergency stop bar, -- Controls mounted on belt loading side, -- Automatic Trabon bearing lubrication system, -- Disc brakes on sanding head motors, -- 30" infeed load area.Note: Some spec's need to be verified

TIMESAVER 2331-24-001 Wide Belt Sander, (3) Heads: 43" Width cap. Drum, Drum, Combination Head.Head Configuration.1st Head: Spiral Rubber covered contact roll, 65 to 70 duro 8" dia., 25 HP motor.2nd Head: Spiral Rubber covered contact roll, 65 to 70 duro 8" dia., 20 HP motor.3rd Head: Combination head with 5-1/2" dia. 65 to 70 duro spiral grooved rubber contact roll and 2-1/2" platen - 15 HPSpecifications: -- 43" x 75" Abrasive belts. -- "Posi-Trak" electronic tracking & pneumatic tensioning. -- Contact roll & platen height adjustments with dial indicators. -- Conveyor belt feed, 20 - 45 FPM variable feed speed. -- Automatic conveyor belt tracking. -- Double infeed & outfeed spring loaded holddown rolls. -- 0" - 5" Max. motorized part thickness opening with LED readout. Equipped with & Features: -- Automatic part thickness setup. -- Air operated disc brakes. -- Motor load meters. -- 14" Infeed conveyor area, and infeed emergency stop.

Single Head Top and Bottom Sander

TIMESAVER 337-2 Wide Belt Sander, (2) Heads36" Width cap., Drum, Combination HeadHead Configurations:1st Head: 11-1/2" Dia. spiral grooved rubber contact roll 40 HP motor.2nd Head: Combination Head, Drum with Platen 30 HP motor. Specifications -- 37" x 75" Abrasive belts with pneumatic tracking. -- 2 HP feed drive; Variable feed speed from 20 - 60 FPM.Equipped with & Features -- Infeed & outfeed spring loaded holddown rolls on both heads. -- Motorized thickness adjustment with indicator, -- 0" - 6" opening. -- Infeed safety stop -- Adjustable shoes before and after each head. -- Controls mounted on belt loading side, --Sanding head motors with air caliper disc brakes, and motor load meters.

Timesavers Model 2331-04-334 3-Head Orbital Sander 43" Machine

TIMESAVER 1321-14-01 43" Wide Belt Sander (2) Heads:43" width cap., drum, combination head.Head Configuration:1st Head: Rubber covered contact roll, 8" dia. with dial indicator heigth adjustment, 20 HP motor.2nd Head: Combination head with a rubber covered contact roll 3-3/8" dia. and 2-1/2" wide finishing platen, 15 HP motor.Specifications: -- Abrasive belt size: 43" x 60" -- Main motors: 20HP & 15HP -- Maximum width stock: 42" -- Minimum part length: 13" -- Maximum thickness opening: 5" -- Feed speed: 15-45 FPM -- Passline height: 33-38" -- Dust extraction: 2000 CFM (5" static pressure) -- Compressed air usage: 4 CFM @ 90 psiEquipped with & Features -- Four Jack Bed Construction -- Dual Infeed and Dual Outfeed Holddown Rolls --Air Operated Disc Brakes -- Centralized Control Panel -- Infeed Stop Bar -- Hour Meter -- Main Motor Percentage Load Meters -- Electronic Go-To Device -- Motorized Thickness Adjustment -- Through-Beam Abrasive Belt Tracking -- Quick Release Outboard Support -- Variable Speed Conveyor Drive

TIMESAVERS 252-4-IC, ... Wide Belt Sander, 4-Head.4-Head, 51" cap. - Great sander for solid wood and veneer panels equipped with (2) Contact rolls and (2) Air platens. Head Configuration1st Head: Rubber covered contact roll, 9-1/2" dia. 60 - 70 Durometer, 40 HP motor.2nd Head: Rubber covered contact roll, 9-1/2" dia. 50-60 Durometer, 30 HP Motor.3rd and 4th Head: Finishing platens, 2-1/2" wide "Veneer Saver" inflateable platens with adjustable timers for leading and trailing edges, 20 HP motor each head.Specifications: -- 38" Constant pass line height of Vacuum conveyor with suction fan and motor bed assembly for veneer and solid wood sanding. -- Adjustable air floating infeed and outfeed hold down shoes. -- 52" x 103" abrasive belts with "POSI-TRAK" electronic tracking.Equipped with & Features: -- Motorized part thickness adjustment with mechanical digital readout. -- Auto part thickness set-up, 0" - 6" opening. -- Hydraulic feed belt operation of 15 - 45 FPM via 7-1/2 HP hydraulic pack. -- 4-Motor load meters, controls mounted on belt loading side. -- Disc brakes on sanding head motors. -- 30" Infeed load area.

Timesavers Single Head Sander Combination Head Model 2311-45-6 Includes transformer

TIMESAVERS 2321-23-21 Planer Sander 2 Heads2-Head, 36" width cap.Specifications: -- 1st Head: 6" Dia. Helical head with (6) spirals of 4-sided carbide inserts, 25 HP motor. -- 2nd Head: Combination head with 5-1/2" dia. contact roll and 2-1/2" wide finishing platen, 20 HP motor, sanding head with 37" x 75" Abrasive belt with "POSI-TRAK" electronic tracking. -- Dial indicators for height adjustments, -- Conveyor belt feed with variable feed speed 20 - 45 FPM, automatic conveyor belt tracking. -- Anti-kick back fingers on infeed; planer head with sectional infeed shoe and double holddown rolls on outfeed, double infeed and outfeed rubber covered holddown rolls on sanding head. -- Motorized part thickness adjustment 0" - 5" with mechanical digital readout; -- Minimum part length 15"; Pass line height 33"-38". Complete with: -- Controls mounted on belt loading side, air activated caliper disc brakes on all heads, load meters for each head and 14" infeed loading area. -- Dust extraction 3,500 CFM, Compressed air usage: 3 CFM @ 90 PSI, -- Total load amps at 230 Volts - 145 Amps.

TiMESAVERS 237-KA IC Planer Sander 2-HEADs (2) Heads Planer Sander Combination, 37" width capacity.Head Configuration: -- 1st Head: 7" Dia. Helical "Quiet Cut" planer head with (6) spirals of 4-sided carbide inserts with 15ø rake angle, head turns @ 3,200 RPM, head adjustment with dial indicator readout, 30 HP motor. -- 2nd Head: Combination Sanding head with 6" dia. contact roll (60 to 65 duro.) and 2-1/2" wide finishing platen, 25 HP motor; sanding head with 37" x 75" abrasive belt with "POSI-TRAK" electronic tracking.Feed System: -- Variable feed speed 15 - 45 FPM, automatic conveyor belt tracking, 3-ply rough top conveyor belt. -- Anti-kickback fingers on infeed, air loaded sectional shoe with dial indicator adjustment and double grooved pinch roll on infeed of knife head. -- Infeed & outfeed pinch rolls on sanding head, air activated caliper disc brakes on all heads. -- Motorized part thickness adjustment 0" - 6" with digital readout.Complete with: -- Controls mounted on belt loading side, main motor fuse protection on both heads, load meters for each head, "over thick" shut-off system and 24" infeed conveyor extension.

Timesaver 2331-45-006 (3) Head Wide Belt Sander;52" Width cap , Drum, Drum, Combination HeadHead configuration 1st Head: 30 HP motor, 8" dia. rubber covered serrated drum with 65 / 70 duro.2nd Head: 25 HP motor, 8"dia rubber covered serrated drum with 65 / 70 duro.3rd Head: 25 HP motor, segmented combination, drum/platen 5-1/2" dia. drum also with 65 / 70 duro drum and a 2-1/2" platen;Specification -- 3rd head has abrasive belt air jet blow off. -- Variable feed 15 / 45 FPM; -- Double in-feed and out-feed rubber covered hold-down rolls.Equipped with & Features -- Star Delta starters on all heads; disc brakes on main motors. -- In-feed stop bar, motorized bed table lift -- PLC controller with HMI interface, electronic abrasive belt tracking. -- This is not a constant pass line sanderNote from Seller: 1800 Hours! We are the 2nd owner of the unit. Well maintained by original owner and purchased by us in 2022. At that time the machine was inspected an by original owner and purchased by us in 2022. At that time the setup and all adjustments done by TS tech

TIMESAVERS 2331-04-334 DUAL HEAD DENIBBING SANDER2-Head, 42" width capacity Sanding / Denibbing system. -- (2) 5" Wide platens featuring a "dual" action head with a high speed orbital movement and combined back & forth oscillation to remove abrasive belt crossgrain scratches; platens designed with a quick change system for abrasive material. -- (1) Nylon abrasive impregnated (150 grit) Cleaning / De-Nibbing brush, 10" dia., drive unit for brush rotation, brush wear adjustment via jack screws. -- Vacuum holddown conveyor system with variable feed speed 5 - 15 FPM. -- Double infeed and outfeed holddown pinch rollers. -- Power raisng and lowering of the conveyor bed with AUTO-SET feature, 0" to 6" part thickness capacity. (4) DUFF-NORTON acme screw jacks under conveyor bed, 36" infeed conveyor area.

TIMESAVERS - 352 HDA, ...Abrasive Planer/Sander2-Head, 51" width cap. Heavy Duty Sander. -- 1st Head: Smooth steel contact roll, 11-1/2" dia., 75 HP motor. -- 2nd Head: Spiral Grooved hard rubber contact roll (11-1/2" dia.) , 75 HP motor; 52" x 103" abrasive belts (6,300 & 4,300 SFPM) with POSI-TRAK electronic tracking. Equipped with: -- Heavy-Duty solid rubber (no vacuum holddown) feed belt for Heavy-Duty operation. -- Motorized part thickness adjustment, 0" - 6" opening. -- 38" - 32" Conveyor height passline with MITUTOYO LED readout, conveyor belt feed. -- 5 HP Variable feed speed from 20 - 60 FPM, smooth rubber conveyor belt. -- Infeed & outfeed spring loaded holddown shoes, infeed emergency stop bar, anti-kickback fingers on infeed. -- Disc brakes on sanding head motors, 18" infeed load area, and motor load meters on sanding heads.

Timesavers Series 1300 (3) Head 43" Wide Belt Sander43" width cap Drum, Drum, Combination headHead Configuration1st Head: 8" dia. contact roll 2nd Head: 8" dia. contact roll 3rh Head: Combination Head 5 1/2" dia. Contact Roll , 2 1/2" width platen on combination headSpecifications -- Dial indicators on drums/platens -- 75" abrasive belt length -- Disc brakes on main motor -- 20-45 FPM feed speed A/CEquipped with & Features -- Auto set-up device -- Motorized lift -- 0-5" opening (33-38" passline) -- 14" infeed loading area -- Quick release outboard support -- Through-beam abrasive belt tracking -- 15" minimum part length -- Emergency stops at infeed and out-feed location

These two sanders are being sold as a line. They are ready for immediate removal, with riggers on site over the first week of August, 2024. - Sander 1: Timesavers Sander Model 352-6KAICBT, bottom frame unit. 3 Head, 50-HP Motors. - Sander 2: Timesavers Sander 352-6KAICBT, s/n 27080 top frame unit. 3 Head, 50-HP Motors

Dust Collection System

Reconditioned Torit 156RF10 baghouse

TORREDA TORMADEX S.A. PA-1200 Hydraulic Wood Turning Back Knife Lathe:Nicely equipped Spanish lathe with dual hydraulic tracers for making quick work of all your demanding woodturning production runs! ... Great for turning baseball bats!Specifications: -- 47" Max. between centers, 9-7/8" max. dia. without traveling steady. -- 3-1/3" Max. dia. through steady rest (larger dia. of 6.2" cap. OPTIONAL); -- High speed automatic loading, feeder accepts pieces up to 4" square. -- 4 HP Motor with (4) turning speeds, 1,200, 2,800, 3,500, and 4,550 RPM. -- (2) HIDRO "T-75" hydraulic reproducing heads with 3" stroke. -- (2) Top mounted hydraulic knives for tenon or pattern cutting (accepts form tools up to 3" wide). -- 2 HP Hydraulic pump motor with (3) carriage feed speeds. -- Features: Pressure sensitive Hydraulic tailstock with Pressure Regulating Valve needed for small, slender turnings to avoid buckling. Pre-rounding tool in front of travelling steady rest. -- Includes: Safety guard, tooling with several roughing and finishing knives.

TORREDA METOR 1600 UNIVERSAL Copy Lathe; -- Specifications: 63" (1,600 mm) Max. between centers, 9-7/8" (250 mm) max. dia. without traveling steady, 3-1/2" (90 mm) max. dia. through steady rest (larger dia. of 6-1/4" (160 mm) cap. OPTIONAL). -- Equipped with: 4 HP Motor with adjustable turning speeds, (1) HYDRO hydraulic tracing head with 3" stroke, hydraulic controlled tailstock. -- (2) Top mounted manual knives for tenon or cutting using form tools (accepts form tools up to 3" wide); 2 HP hydraulic pump motor with adjustable feed speeds. -- Actual model is HIDRO 80/12 mm. -- Includes matching knife grinder and accessories as pictured

TRAVAINI TRO 501-1A-200V "40 HP VACUUM PUMP (LIQUID RING) 11,969 Hours:40 HP Travaini liquid ring, single stage vacuum pump "TRSC 100-700/C/F". Nominal capacity 500 ACFM @ 20" HgV; max Vacuum 27" HgV. -- Pump materials:Include cast iron housing, ductile iron impeller, and stainless steel shaft. Shaft seals are carbon face with viton elastomers. -- 40 HP:200 Volt, 3-Phase, 60 Hz, TEFC monoblock assembly for direct drive, no field alignment needed. -- Sealing fluid re-circulating system includesReservoir of carbon steel with fluid level gauge and drain, high-efficiency discharge separator and oversized heat exchanger. -- High temp switchTo protect against over-temp operation. -- Suction line accessories includeInlet check valve, vacuum gauge (0 - 30" HgV), inlet filter assembly, manual unloader valve, and vacuum relief valve. -- Heat exchangerIs an air cooler type made from aluminum and extended surface fins. -- Electrical controls include:Starter/overload reset, pump running light, hour meter, hi-temp light, and terminal blocks, all mounted in a NEMA 12 cabinet.