Woodworking Equipment For Sale

Dubois Lineal Sprayer with Guns

The Dubois SP-12 Linear Spray Machine is an automated linear finishing machine that can be used for a variety of applications including priming, staining, sealing, lacquering, etc. of linear stock. This spayer comes with (3) three arms, (3) three guns and (1) one paint pump. The guns are Binks spray guns Model 363, and Binks pump.Compatible with both waterborne and solvent based coatings --Three adjustable gun arms --9’-0"; long variable speed live roll conveyor w/ electric powered drive --Pneumatic gun trigger mechanism to automatically trigger guns on/off --Infeed guide fences --Top roller hold-down on infeed table --Ability to enable/disable individual guns --Easily cleaned spray trough --Adjustable atomizing air pressure --Adjustable fluid pressureIncluded optional features: &#9679 Stain wipe station mounted to outfeed with stain wipe brush &#9679 Exhaust system with spray enclosure, exhaust fan, & exhaust filter system &#9679 Denibbing station mounted to infeed

DUBOIS Vertical Edge Fill System with Micro UV This machine is designed to fill voids and defects in edges for a smooth, quality finish. These coaters are ideal for filling porous open grain panels like oak, veneers, particleboard, and MDF. Compatible with solvent based, water based, and UV fill coating.1.1 One (1) Continuous chain transport system- Top and Bottom chain transport conveyor with speed matching attachment conveyor chain- Aluminum backed chain pads with EPDM covering1.2 Two (2) double sided vertical edge denibber/buffer- Operator side Adjustable up to 12"; wide, back side fixed edge- Post mounted vertical denibber head- 12"; dia. x silicon impregnated scuffing wheel, buffer wheel to be determined- Dust hood with 4"; connection- Vertical head oscillation for even brush wear- Inverter controlled drive provides speed control for brush and oscillation1.3 Two (2) double sided vertical edge fill stations- Operator side Adjustable up to 12"; wide, back side fixed edge- Electric motor driven Applicator and Doctor roll drives- Quick change applicator sleeve design, 1-1/2"; face- Stainless steel distribution pipe with spring tension- 9"; dia. chrome plated reverse roll- Stainless steel catch pan and drain lines- 3/8"; pail mounted pump and agitator- Spring loaded doctor bar, urethane dr. blade- Air cylinder dr. roll engagement with stroke adjuster- Inverter controlled drives provides speed control for applicator and doctorrolls1.4 Edge Cure UV Oven Banks- Each bank to consist of Two (2) double sided Fusion F600 Microwave UVovens- Space for two (2) future double sided Microwave UV Units- Individually adjustable three (3) position lamp power selector switch(300, 400 & 600 w/in.)- Irradiator cooling exhaust fan for each set of four (4)2. Control Panel System- NEMA 12 Hinged Door Enclosure, with disconnect, required fuses, door mounted buttons and cooling fans- Allen Bradley HMI, PLC items included- Top mounted panel cooling fan- Required Inverters· Edge Fill Finishing Machineo Top and Bottom Conveyor driveso Denibber/Buffer Brusheso Denibber/Buffer oscillatorso Applicator Rollso Doctor Rollso Reverse Rollso UV oven Exhaust fansDesign Parameters- Machine is located in Explosion Proof Area- Voltage= 480 V., 3 Ph., 60 Hz.- Design Speed = 70 - 200 FPM- Line height = 36";- Max./Min. Part Width: 12"; / 2";- Max./Min Part Length: 245"; / 24";- Max./Min Part Thickness: 1-1/4"; / 3/8";- Paint Color· Main Frame and Conveyor: Blue / TS White· Guards: safety yellowNotes:- ¼"; product has the potential of being processed in this machine but has less probably of being successful the wider the product.

DURAMAC - DUR52-2, ...2-Head Wide Belt Sander2-Head Wide Belt Sander with: Drum, combi-head, and brush cleaner. -- Max. working width: 52". -- Max. working thickness: 6". -- 23" Infeed load space. -- 50" Wide rubber conveyor belt size. -- 1st Head: Grooved rubber contact sanding drum; 40 HP, 230 Volt - 3-phase drive motor. -- 2nd Head: Combination contact drum & polishing platen; 30 HP, 230 Volt - 3-phase drive motor. -- Spring-loaded pinch rollers. -- Electronic belt tracking, pneumatic belt tensioning. -- (1) Rear top outfeed panel brush cleaning head, 0.5 HP, 230 Volt - 3-phase drive motor. -- Power raise & lower of worktable. -- Inverter driven feed works drive motor for variable speeds, 0 to 60 FPM. -- Front operator control station; motor ammeters. -- TOSHIBA Feedworks inverter. -- "DP-626S" electronic digital readout for setting table heightAlso Available: -- Transformer for 600 Volt operation, 112.5 KVA.

•Durand plywood stacker •Will stack panels up to 5ft wide x 10ft long panels •Serial # 1286 •Was in use on skinner/trimmer line when the plywood mill went out of business •Currently stored inside, and ready to load on a truck •No charge for loading

Line Shaft Ready Triple Combination Table Saw/Band Saw/Router all in one.

Maximum Assembled Product Size: 37.5” x 98” Minimum Assembled Product Size: 11.375” (vertical) x 9.75” (horizontal) with spacer blocks 7.5” (vertical) x 5.5” (horizontal) Maximum Framing Width: 4” Minimum Framing Width: 1.5” Tubular Steel Frame THK Linear Bearings and Rails (1) Allen Bradley Compact Logix PAC (4) Allen Bradley Kinetix Servos and Drives a. (1) Vertical Beam b. (1) Horizontal Beam (2) On the Upper Right Hand Clamp to ensure that uniform pressure can be applied regardless of the cut accuracy of the frame parts (1) Hoffman Upright Enclosure Allen Bradley Control Components (Push Buttons, Relays, Power Supplies, Buzzer, etc.) (1) Hoffman Air Conditioner for Electrical Enclosure EMS Press Control/Server Communication Software Package (4) Tregarne Woodwelder with Production Gun

Eagle Machinery Infeed Deck: Chain driven, approx 12" wide x 195" long Eagle tilt hoist table

EKSTROM CARLSON - Model EE, ...Straight Line Rip SawSpecifications: -- 30 HP Saw arbor motor. -- Max. thickness 3-1/4"; with 16"; dia. saw blade (no blade). -- 5 HP Feed Motor with feed rates infinitely variable to 280 FPM. -- (3) Lower infeed rollers are chain driven and are adjustable from 0° - 5°. -- Elongated pressure bar housing assures the proper guidance across the entire table length.Equipped with & Features: -- Spring-loaded rollers with 1 in. yield. -- Dual position and lubrication system; (2) outfeed rollers. -- Please note: Chain appears to be in very good condition.

EKSTROM / CARLSON - 18, ...Pump Sander Pump Sander with: (2) 1" Dia. horizontal spindle; 2 HP - 1,200 RPM enclosed motor; mounted on heavy cast iron pedestal. -- Complete with: Push button magnetic controls & starter; 4" dust collection port.

Single Line Rip Saw 110V 3 Phase

EKSTROM CARLSON - Model EE, ...Straight Line Rip SawSpecifications: -- 30 HP Saw arbor motor. -- Max. thickness 4-1/2"; with 16"; dia. saw blade (no blade). -- 5 HP Feed Motor with feed rates infinitely variable to 250 FPM. -- (3) Lower infeed rollers are chain driven and are adjustable from 0° - 5°. -- Elongated pressure bar housing assures the proper guidance across the entire table length.Equipped with & Features: -- Spring-loaded rollers with 1 in. yield. -- Dual position and lubrication system; (2) outfeed rollers. -- Please note: Chain appears to be in very good condition. -- 3 extra blades

good condition 3 phase/480 volt

Elio Valeri CNC Lathe This is originally an Italian lathe made by Elio Valery designed to make queen Ann legs or axe handles. Seller modified it to make table legs (4 at a time). Working length 60" Actually setup with 1 or 2 spindles, but project can be completed to add 2-more spindles.

ELIO VALERI ELVAP 120 Copy Lathe. -- General data: 48" max. length cap., 7" max. dia. without steady rest, 3.93" max. dia. with steady rest, and up to 2.5" x 2.5" dia. with steady rest for square pieces; 0 - 39 FPM forward and 0 - 52 FPM return speed, 5.5 HP motor, 1,300 - 3,500 - 5,000 RPM; -- Features: Air/oil feed and copier, chain head stock drive, gate loading, pattern; pneumatic tail stock, automatic pneumatic control program.

EMC PIONEER 2RK Wide Belt Sander, (2) Head: 37" Width capacity. Drum, Combination Head.Head Configuration: 1st Head: -- Rubber covered contact roll 180 mm diameter.2nd Head: -- Combination Head, rubber covered roller with padSpecifications: -- Useful working width: 950 mm (37"). -- Working thickness min/max: 3 - 170 mm. -- Abrasive belts length: 1,900 mm. -- Abrasive belt width: 975 mm. -- (2) Feed speeds: 5 - 10 m/min. -- Electronic digital display for working thickness. -- Abrasive belt oscillation by electronic photocell. -- Main drive motor 15 HP -- Feed drive 2 to 19 Meter/min.

EMC MERCURY 1350 2RK ... Wide Belt Sander with (2) Sanding Heads; Roller and Combination head roller/pneumatic pad.Versatile, medium duty machine, ideal for cabinet shops etc.TECHNICAL DATA: -- Useful working width 1,350 mm (53"). -- Working thickness min./max. mm 3 - 170 (1/8" - 6-11/16"). -- Abrasive belt dimension (length) 2,200 mm (86-5/8") x (width) 1,320 mm (52"). -- Feed belt speeds adjustable by electronic inverter from 3 to 19 m/Min (10 - 62 FPM). Head configuration:1st Head: Steel Contact Roller -- Roller diameter 180 mm (7"), spirally grooved. -- Automatic abrasive belt grit compensation with "Grit-Set System". -- Motor power 11 kW (15 HP) driving both heads, with soft starter. -- On/Off Selector control with pneumatic piston to select roller. -- Automatic Star-delta starter. -- Speed rotation: 18 m/Sec (59 FPS).2nd Head: Combination Roller & Pad. -- Roller diameter 140 mm (5-1/2"). -- Rubber covered roller with hardness 45 Shore. -- Automatic abrasive belt grit compensation with "Grit-Set System". -- On/Off Selector control with pneumatic piston to select roller. -- New pneumatic aluminium sanding pad, lamina 40 mm. With On/Off selector. -- Quick Change System for removable pad with felt, rubber and graphite. -- Rotating cutting speed 18 m/Sec (59 FPS). -- Driven by same main motor, with soft starter.Abrasive belts oscillation by means of electronic photocell sensor.Feed System: -- Working thickness min./max. mm 3 - 170 (1/8" - 6-11/16"). -- Motorized table lifting including fine adjustment, on 4 precision screws. Natural rubber conveyor belt, machined. Automatic feed belt centering device. Electronic digital display for working thickness; resolution 0.1 mm (0.004"). -- Feed belt speeds adjustable by electronic inverter from 3 to 19 m/Min (10 - 62 FPM). -- Table rollers. Extension supports with idle rollers in infeed & outfeed.Centralized Control Cabinet: -- Control panel with self-diagnostics alarm control unit. -- Analog load meter on main control cabinet. -- Table lifting-lowering thickness system, electrically controlled. -- AUTOMATIC Delta - Star starter on main motor and IP 54 protection against dust & moisture. Centralized Independent Pneumatic Control Cabinet: -- Pneumatic air filter with automatic water-drain system. -- Pneumatic adjustment for "Grit set system". -- Pneumatic plant working without lubrication. Compressed air pressure 6 bar (85 PSI). IP 54 protection against dust & moisture. Safety Features: -- Anti-kickback infeed protection. -- Oversized parts infeed protection by swinging bar. -- Emergency push buttons front & rear. --Automatic brake on main motor. -- Automatic emergency stop and alarm displayUSA UL or Canada CSA Safety Features

EMC UNDERTOP 1300 2+2 - Wide Belt Sanding Line Top + Bottom, both with (2) Sanding Heads; Steel Roller, Rubber covered Roller.This machine is equipped to process cement fibers!Useful working width 1,300 mm (51"). Working thickness min./max. 3 - 160 mm (1/8" - 6-5/16"). Both Bottom + Top units are equipped as follows:1st Head: Steel Roller "R", Belt dimensions: 1,900 x 1,320 mm (74" x 52"). -- Roller diameter:190 mm (7-1/2"), spirally grooved. -- Constant control to any position with accuracy 0.02 mm. -- "Grit-set system" for sanding belt grit compensation. -- Rotation: Against feed (clockwise). -- Motor power: 22 kW (30 HP) with Automatic star-delta starter. -- Abrasive Belt cutting speed: 21 m/Sec (69 FPS). -- Air Jet Blower for abrasive belt cleaning.2nd Head: Roller "R", Rubber covered, spirally grooved. Belt dimensions: 1,900 x 1,320 mm (74" x 52"). -- Roller diameter:190 mm (7-1/2"). Shore hardness 85. -- Constant control to any position with accuracy 0.02 mm. -- "Grit-set system" for sanding belt grit compensation. -- Rotation: Against feed (clockwise). -- Motor power: 15 kW (20 HP) with Automatic star-delta starter. -- Abrasive Belt cutting speed: 21 m/Sec (69 FPS). -- Air Jet Blower for abrasive belt cleaning. Feed system: -- Constant pass line, 980 mm (38-9/16") from floor. -- Idle table rollers support in infeed and outfeed. -- Rubber covered presser rollers, grooved. -- Variable feed belt speed, adjustable from 3 to 19 m/Min (9.8 - 62 FPM), Inverter Controlled, synchronized feed speed between both machines. -- Motorized height adjustment on (4) precision screws. -- Large diameter screws on machined guides with columns and pistons. -- Automatic feed belt centering device. -- Pre-welded machined working table. -- Pneumatic air floating pressure holddown shoes at infeed, in middle position, and in outfeed position. These pressure holddown shoes are chrome hardened for processing of cement fibers!General Machine Features: -- Independent main motors. -- Analog ammeters, for each motor, on main control cabinet. -- Electronic motorized grit set system, control from touch screen for each (head) working group. Electronic programmable color TOUCH SCREEN LCD display, 7" wide -- Resolution 640 x 480 pixels. -- PLC with micro-processor of latest generation, modular and expandable. -- Memory capacity: (100) working programs or more. -- Graphic synoptic to facilitate programming. Front protection IP 65 against dust & moisture.Software facilities: -- Automatic motor sequence starting. -- Display report and reset of alarms (self diagnostic) with memory records. -- Command, programming and display for: &#9679 all electronic pad functions. &#9679 thickness. &#9679 feeding. &#9679 all speed control inverters. &#9679 selected groups. &#9679 blowers, including compressed air saving function. Options Included: -- Vacuum beds both on top + bottom, 4 kw (5,5 HP) each. Vacuum unit for holddown of smaller parts, mounted inside o

EMC EXPLORER 1100 2RK ... Wide Belt Sander with (2) Sanding Heads; Roller and Combination head roller/pad.Versatile, medium duty machine, ideal for cabinet shops etc.TECHNICAL DATA: -- Useful working width 1,100 mm (43"). -- Working thickness min./max. mm 3 - 170 (1/8" - 6-11/16"). -- Abrasive belt dimension (length) 1,900 mm (75") x (width) 1,120 mm (44"). -- Feed belt speeds adjustable by electronic inverter from 3 to 17 m/Min (10 - 55 FPM). Head configuration:1st Head: Steel Contact Roller -- Roller diameter 142 mm (6") -- Automatic abrasive belt grit compensation with "Grit-Set System". -- On/Off Selector control with pneumatic piston to select roller. -- Motor power 11 kW (15 HP). -- Automatic Star-delta starter. -- Speed rotation: 18 m/Sec (59 FPS).2nd Head: Combination Roller & Pad. -- Roller diameter 142 mm (6"). -- Rubber covered roller with hardness 45 Shore. -- Automatic abrasive belt grit compensation with "Grit-Set System". -- On/Off Selector control with pneumatic piston to select roller. Flexible sanding pad. Quick Change System for removable pad with felt, rubber and graphite. Rotating cutting speed 17 m/Sec (55.8 FPS). --Driven by same main motor.Abrasive belts oscillation by means of electronic photocell sensor.Feed System: -- Working thickness min./max. mm 3 - 190 (1/8" - 7-1/2"). -- Motorized table lifting including fine adjustment, on 4 precision screws. Natural rubber conveyor belt, machined. Automatic feed belt centering device. Electronic digital display for working thickness; resolution 0.1 mm (0.004"). -- Feed belt speeds adjustable by electronic inverter from 3 to 17 m/Min (10 - 55 FPM). Centralized Control Cabinet: -- Control panel with self-diagnostics alarm control unit. -- Analog load meters on main control cabinet. -- Table lifting-lowering thickness system, electrically controlled. -- AUTOMATIC Delta - Star starter on main motor and IP 54 protection against dust & moisture. Centralized Independent Pneumatic Control Cabinet: -- Pneumatic air filter with automatic water-drain system. -- Pneumatic adjustment for "Grit set system". --Pneumatic plant working without lubrication. Compressed air pressure 6 bar (85 PSI). IP 54 protection against dust & moisture. Safety Features: -- Anti-kickback infeed protection. -- Oversized parts infeed protection by swinging bar. -- Emergency push buttons front & rear. --Automatic brakes on main motor. -- Automatic emergency stop and alarm displayOption: TAMPICO Cleaning Brush, 150 mm (6") diameter. Please add ...$3,400USA UL or Canada CSA Safety Features

EMC VENUS 1300 1K ... Finishing Sander with (1) Sanding Head: Combination Head.Useful working width 1,300 mm (51"). Working thickness min/max mm 3 - 170 (1/8" - 6-5/8").Working Unit: Combination Roller & Pad. -- Roller diameter 142 mm (5-5/8"). Rubber covered hardness 85 Shore. Roller pressure adjustment control & "Grit-set system". Main Motor On Off Selector control with pneumatic piston to select roller, 22 kW (30 HP) Automatic star-delta starter Rotating cutting speed: 18 m/Sec (59 FPS). -- PNEUMATIC Controlled Flexible Sanding Pad Including On-Off Selector: Quick Change System: Removable pad with felt, rubber and graphite. Rotating cutting speed 18 m/Sec (55.8 FPS). Abrasive belts oscillation by means of electronic photocell sensor.Feed system:CONSTANT PASS LINE - fixed infeed height 900 mm (35") from floorIdle table rollers support in infeed and outfeedRubber covered presser rollers, groovedVariable feed belt speed, adjustable from 3 to 19 m/Min (9.8 - 62 FPM). Inverter ControlledLarge diameter screws on machined guides with columns and pistonsAutomatic feed belt centering deviceElectronic digital display for working thicknessGeneral Machine Features: -- Analog ammeters on main control cabinet. -- Electronic motorized grit set system, control from touch screen.Electronical Panel: -- Check Control Self Diagnostics with Alarm Control. -- Analog Ammeter on the main control cabinet. -- Infeed table thickness system electrically controlled. -- Independent Overload protection.Safety: -- Infeed front emergency swinging bar for oversized panels. -- Infeed protection pressing blade to avoid pieces to go back to operator. -- Rear and front emergency push buttons. -- Automatic brake on abrasive belts motors. -- Automatic emergency stop and alarm display in case of: &#9679 Low Air Pressure. &#9679 Doors opened ("easy maintenance and inspection"). &#9679 Electric motors overloading. &#9679 Emergency detector for over thickness material cut. &#9679 No tension on abrasive belt. &#9679 Abrasive belt lateral mistracking. &#9679 Abrasive belt broken.Idle table rollers support in infeed and outfeedCentralized Control Cabinet: &#9679 IP 54 protection against dust & moisture. &#9679 Analog ammeter on main control cabinet. &#9679 Table lifting-lowering thickness system electrically controlled. &#9679 AUTOMATIC Delta - Star starter on abrasive belts motors. Centralized independent pneumatic control cabinet: &#9679 IP 54 protection against dust & moisture. &#9679 Pneumatic air filter with automatic water-drain system. &#9679 Pneumatic adjustment for "Grit set system". &#9679 Pneumatic plant working without lubrication. &#9679 Compressed air pressure 6 bar (85 PSI). Options Available: Tampico Brush natural fiber brush for cleaning of the pieces, diameter 150 mm (6"). Motor Power 1.1 kW (1.5 HP). $3,950