Woodworking Equipment For Sale

System includes: Vacuum Coater UV Oven with (9) lamps Lateral Transfer Table Max width 9" Able to run clear or pigmented coating

Two Bay 52" capacity Pneumatic clamping

Marbel LS-1 Laminate Slitter

Marbel PR6-61 Closed End Pinch/Nip Roller 61" capacity 1500# of pressure with 5-1/2" diameter rollers 3" material thickness capacity feed rate 27 FPM 1/4 HP motor 115 volt

Marbel PR6-61 Closed End Pinch/Nip Roller 61" capacity 1500# of pressure with 5-1/2" diameter rollers 3" material thickness capacity feed rate 27 FPM 1/4 HP motor 115 volt

2005 Marathon Spray Booth 14' wide x 25.5' long x 8'9" tall Booth only no racks, spray guns, paint pots etc included

MARINUS Powermax 300 HD End Matcher With Defecting, Cut to Length & Optimizing Cut-Off CapabilitiesFeatures & Specifications: -- Heavy and stable construction -- Cutterhead Carriage and Clamp System utilizes HD Lineal Bearings – grease lubricated. -- Heavy Duty – low maintenance Feed Chains Into machine and takeaway of material after cutting/ end matching. -- Continuous high-speed feeding system with accurate positioning utilizing HD Servo Drives. -- 2 Servomotors for maximum feed control and acceleration and deceleration control -- Servo-driven feed motor & gearbox for highest efficiency speed feeding and control of the cutterhead carriage includes independent step-less speed control forward & reverse. -- Pneumatic side pushers (holding material firmly against the fence) for guaranteed square angle cut. -- 2 Cut-off sawing servo motors: 5 HP each (3,0 kW) – 450 mm (17.7";) dia. blades with inverters (VDFs) for varying blade speed -- 2 High-speed milling head servo motors with inverter (VFD) (12HP - 7,5 kW each) with speeds to 12,000 RPM - 5"; (125 mm) dia. -- Adjustable cutterhead stroke based on material width to increase throughput speed based on the width of material input. -- 1 Luminescence-Sensor camera for defect crayon mark -- Inductive-Sensors – for detecting the position of the carriage and the others for detecting the positions of the saw blades. -- Cutoff waste powered belt conveyor in machine (below feed system- 12"; from floor) with drive motor for waste cutoff pieces taken to the outfeed end of the machine. Other Technical Specification: -- Machine is completely enclosed by safety doors. -- Machine is produced to CE Safety and Electrical Standards to UL/CSA Standards -- Lenze PLC Control -- Operation from operator’s control with touch screen control – mounted on the front right cover of the machine. -- Air pressure required – 85 PSI (6 Bare) -- 1x 8"; (200 mm) & 2 x 4.75"; (120 mm) dia dust outlets with approx. 5,000 to 5,500 mm and from 3050 to 3350 CFM -- Router Remote Access – with an internet connection, factory can monitor the performance of your machine. Also allows for easy access to service and softwareupdates and downloadsInput & Output Material Specifications -- Board Widths: 2";(50mm) Min. to 12.28";(312mm) Max. Min width 1.75"; (44.5 mm) min. -- Board Input Lengths: 17.9"; (450 mm) Min. to 20 ft.(6000mm) Max. -- Board Output Lengths: 15.9"; (400 mm) Min. -- An available short-piece option can be added to reduce output. length to 10"; (250mm) Min -- Board Widths: 2";(50 mm) min. to 12.28";(312 mm) max. -- Board Input Lengths: 17.9"; (450 mm) Min. to 20 ft. (6000 mm) Max. -- Board Thickness:4"; (10 mm) Min. - (to 0.315"; (8 mm) on request) (to 2"; (50 mm)Standard Programs / Programming -- The machine is equipped with 2 Primary Programs: -- 1. Endmatching – includes trimming ends and endmatching -- 2. Cutting only (no endmatching) -- 3 Sub-Programs -- 1. Defecting

Marinus Powermax 300 End Matcher HB Precision attachment 400 v (will need transformer in US)

MARUNAKA Model RD – 8J WIDE Single Deck Veneer Roll Dryer;Complete with the following features: -- 1988 - year of manufacture. --Working width – 51"; --Length of the dryer – 24 Ft (4 Sections) --Type of heating - Steam --Operational in 2018 when mill closed --Professional rigging and loading available.

MARUNAKA Model RD-3UB/RD-6UB (Connected) Single Deck Veneer Roll Dryer;Complete with the following features: -- (3) 3 HP circulating fans with (1) 3 HP exhaust blower thru the ceiling. -- Optional heat source: electric (7) Elements/Zones, computer controlled thermocouples in addition to (2) Natural gas burners (OEM).. Both dryers have a 100amp circuit breaker with 100amp fuses. The RD 8 operates with 4 fan motors and 4 heaters. The RD 6 has 3 fan motors and 3 heaters";.. -- Capable of temperatures to 120° Celsius (250° Fahrenheit). -- Working width 1000 mm or about 39 inches. Veneer is fed endo.Please Note: -- Dryer is (2) separate units; all equipment will fit into a 40' container for shipment from Eastern USA. -- All equipment is in good working condition including all fans and blower, temperature control works properly; feed roll drive works well. -- Rolls have been nickel treated to minimize corrosion/oxidation. -- This dryer equipment is still in place. -- MARUNAKA (2) Models: RD-3UB and RD-6UB currently connected to increase capacity. Can easily be separated.NOTE: Refurbished in 2005, operated from 2005 - 2012. Still operational ready to work!

MASTERWOOD PROJECT 313 CNC MACHINING CENTER (W/ACT/BORING): -- Specifications:Working Capacity:"X" Axis 3,080 mm (121"), "Y" axis 1,100 mm (43") width; -- Positioning Speed:Programming speed in X-axis 197 FPM (60 MPM), Y-axis 162 FPM (49 MPM), Z-axis 58 FPM (18 MPM). -- Boring unit:(13) independent vertical spindles, (9) in X-axis, (5) in Y-axis; (4) horizontal spindles with (1 + 1) in X-axis for edge boring in the left- & right-hand panel edges. -- Machining:(1) 7.5 HP (5.6 kW) high speed router (1,000 - 24,000 RPM) by frequency inverter; 1.5 HP (1.1 kW), 6,000 RPM grooving saw with manual rotation for X-axis or Y-axis; -- Work Table: (6) moveable support rails with (2) vacuum cups ea., double zero settings, (6) pneumatic backstops and (2) pneumatic side stops creating (2) working zones. -- Operator & Machine Control:TECNOSUD "K68800" Microprocessor control for (3) axis, lineal, circular, and helical interpolation. Equipped with 14" color video graphic monitor, keyboard for data entry, 1.44 MB floppy disk drive, 64K RAM, RS-232 for possible connection to office PC, all mounted in separate free-standing control cabinet; features to run CPL/Parametric "TRIG" programming and "Spline" CAD/CAM. -- Complete with: Dual zone vacuum pump. Ontario Hydro approved electrics. -- Actual Model is MASTERWOOD PROJECT 313

MASTERWOOD OMB1CN3-TF Horizontal Slot Mortiser. One NC working head (3) axis with programmable microprocessor.. Machines a sequence of slots on windows, doors, shutter, or cabinets without moving workpiece. Continuous cycles with loading/unloading. -- Equipped with: (1) Maka style chisel mortising unit, (1) Vertical routing unit and (1) TF Horizontal routing unit. High frequency drilling - routing with controlled axis, DC motors, ball screw driven. -- Max Mortise workpiece size 150x110x2800 mm length, (5.9"x4.3"x110.2"). Vertical and horizontal routers 142"; length. -- Max slot depth 130 mm (5.1"). Max vertical head stroke 140 mm (5.5"). -- Features: Pneumatic hold-downs bar mounted above table. Flip-up pneumatic pressure beam for additional support when needed. Free-standing control and electrical cabinets house computer monitor and keyboard. Master universal electronic system controller (MW CN10 Centromac) -- Vertical routing assembly: 4HP, 220/380v 3 PH, 9,000 RPM -- Horizontal routing assembly 5"; 220/380v, 3 PH, 9,000 RPM -- Memory for 50 cycles. Mirror imaging with preset tool speed (over-writeable knob). -- Total load 21 KVA -- Overall dimensions 4200mm long x1600x1600mm (166"x63x63"). Electrical cabinet 1,000 high x 450x950mm (40"x 18"x38"). Approx. weight 3800 Kg (8,400 Lbs.).

The Rip Saw is still in good running condition and still in use.

Mattison 224 4 head moulder, 220 volts, 3 phase Call 800-459-2148 for more info.

Mattison 404 Rip Saw Seller was using until they upgraded to a gang rip. Ready to ship.

Madison 202 Straight Line Rip Saw

Mattison 202 Straight Line Rip

Description Mattison "55-F" Turning Lathe - Back Knife 30" Cap. in length and 4" x 4" cap. dia. - Pneumatic feed; rear arbor with cutter-head driven by a 10 HP V-belt motor. Work piece rotation is belt driven by main motor with variable speed gear box, double end drive, mechanical feed of work piece into cutter head. Rear dust shroud with collection outlet.

Mattison 404 Straight Line Rip 230 Volt 3 Phase 25 HP Total 230/460 Dual Voltage on 20HP Mandrel Motor

MATTISON - 404, ...Straight Line Rip SawSpecifications: -- 15 HP - 3,600 RPM Direct drive arbor motor; 14" dia. max. saw blade cap. (9" smallest dia.), 1-1/2" dia. arbor; 4" thickness capacity. -- Table size of 65" x 77" long. -- 30" Distance from saw to left edge of table. -- 24-1/4" Between saw & column; 24" rip distance to right of gauge. -- Top roller holddown with 7-1/2" shortest stock handled under (1) roll; 15" under (2) rolls.Equipped with & Features: -- Overhead cutting design with single cast chain links. -- Chain with automatic oil lubrication. -- 2 HP Feed motor with (4) feed speeds. -- (2) Carbide rip blades.NOTE. Comes with a 208 Volt Transformer.