Woodworking Equipment For Sale

SICOTTE - J 3H-6, ...Vertical Boring Machine24" x 72" Table size, (5) Spindles.Equipped with: -- (3) 1 HP Motors mounted on 24" long arms with motor starter and overload relay. -- (5) 1-1/2" Dia. spindle with set screw locking 1/2" cap. -- (2) Spring-loaded holddowns. -- (1) Additional motor started with overload for future installation of a spindle drive motorFeatures: -- 0" - 8" Vertical table feed, hydraulically operated, variable feed, and table travel adjustable from front of machine. -- 3 HP Hydraulic pump motor with reservoir. Complete with: -- Electrical Control System with separate motor controls. -- Single or continuous stroke. -- Manual and automatic cycle. -- Foot pedal actuation. -- (1) Safety guard.

SICOTTE J 20-5 Horizontal Boring Machine:12" x 60" Steel table with 2-1/2" manual up-and-down adjustment. -- (4) Drive groups with 1-1/2 HP - 3,500 RPM drive motor each, timing belt & pulley drive. -- (7) Spindles, 2" in dia. and with Jacob chuck 0 - 1/2" capacity. -- Spindle feed powered by 3 HP hydraulic pump, 0" - 6" stroke, variable speed up to (30) strokes/Min.Complete with: -- (3) Pneumatic holddowns, -- Cycle timer 0-30 sec., -- Automatic/manual cycle with foot pedal switch, -- Sinvle or continous stroke -- Emergency stop.

SICOTTE J3H-A-6 Angular Vertical Boring Machine24" x 72" Table size Angular boring machine for chair seat -- (6) Hydraulic self feed spindle having 3 7/8" adjustable stroke and variable speed feed, 1 HP motor, jacob chuck 0 to 1/2" capacity, mounted on 24"long arms with timing belt drive. -- The spindle can be set at coumpônd angle angle with 30 deg front to back and 15 deg right top left. -- (2) Air holddowns. -- 0" - 8" Vertical table feed hydraulically operated that can be used when you drill vetically without angle, , variable feed and table travel adjustable from front of machine, -- 3 HP hydraulic pump motor with reservoir. Complete with: -- Electrical control system with separate motor controls, -- Single or continous stroke, -- Manual and automatic cycle and foot pedal actuation, -- Selector switch to activate each spindle manually . -- This machine is design for chair seat boring or any other application where angular holes are required.

This line has not been run in approx 10 years. The current warehouse/facility may also be available for sale.

SILVER SJK-21 Horizontal & Vertical Boring on 32 mm centers.(21) Spindles in line on one boring head (aluminum alloy single block), drills vertically from top & horizontally from rear. -- Features pneumatic adjustment for horizontal boring.Specifications: -- Max drill dia. is 1.38" (35 mm); Max panel thickness is 2.36" (60 mm); Table size 36" x 19.75" (914 x 502 mm). -- Length of cross fence is 102" (2,600 mm); length of aluminum table fences are 39" (1,000 mm) to the left and 28" (710 mm) to the right with flip stops.Equipped with: -- Depth stop adjustment, (2) holddown air cylinders, and foot pedal operation for clamping/drilling cycle. -- 2 HP - 3,600 RPM TEFC motor with thermal overload protection and low voltage controls.. -- Includes (12) Quick change chucks..

SILVER SJK-19T Line Boring MachineSingle line vertical boring machine with (19) spindles at 32 mm centers driven through a powerful 1.5 HP motor.Equipped with: -- Foot pedal controlled pneumatic boring cycle -- Adjustable boring feed speed -- Adjustable boring depth for fast changeover -- 2 Pneumatic cylinder clamp for solid hold-down to the material. -- 3 Meter long back fence for long line boring with flip stops -- (2) Positioning pins at both end of boring head to set up for longer line boring quickly -- Quick change chuck for fast changeover (19 pcs included)Specifications: -- No. of Spindles....................................................................................... 19 -- Distance between each spindle.............................................................. 32 mm -- Max Boring Depth .................................................................................. 60 mm (2.36") -- Working Table Size................................................................................ 800 x 500 mm (31.5" X 19.68") -- Table Height from Floor......................................................................... 780 mm (30.35") -- Max Boring Depth from Edge................................................................. 155 mm (6") -- Electric .................................................................................................. 220 V / 60 Cy / 3-Ph -- Machine Size (LxWxH) ........................................................................... 920 X 670 X 1490 mm (36.25" x 26.37" X 58.66") -- Net Weight ............................................................................................ 220 kgs. (484 Lbs)

Silver Straight Line Rip Saw 15 HP Motor

Model SF-45A 600 V / 3 Ph / 60 Hz 10ft table 8.5 HP main motor provides(2) cutting speeds 3,800 & 5,200 RPM

SILVER - SJK-65: Construction & Line Boring Machine(4) Vertical Boring Heads; 21-spindle from bottom on 32 mm centers; (1) Horizontal Boring Head; (21) spindles on 32 mm center. -- 3" (75 mm) Max. drilling depth; (3) 4.0 HP - 3,450 RPM motors; pneumatic-hydraulic drill head advance with: Speed control with working speed or (0 - 15) cycles per min.; head height adjustment with: Mechanical digital readout; 51" x 37" working capacity. -- Equipped with: (2) Pneumatic holddown clamps; pneumatic foot pedal control.

SILVER 6023AH Moulder Feed Through 6-Head (B-R-L-T-T-B), working cap. 9-1/16" x 6". Head sequence: -- Bottom 10 HP, top 10 HP, right 10 HP, left 10 HP, top 15 HP, top 15 HP and bottom 15 HP motor. -- Spindle dia. 40 mm with cutterhead speed of 6,000 RPM. -- All spindles with mechanical digital readouts. -- Feed: Variable speed of 18 - 82 FPM, with 5 HP feed drive motor. Powered feed rollers top and bottom. -- Infeed: Straightening table 2 M (6'6"), with side pressure roller and table lubrication pump. Includes:: -- Centralized control panel, -- Sound and safety enclosure.

SIMI 5' x 10' HOT PRESS Platen dimension 123" x 63" (3,125 mm x 1,600 mm). -- Max. daylight opening 17" (430 mm). -- (8) Hydraulic upstroke cylinders with diam. 6" (150 mm). -- Electrically heated platens with a maximum heating temperature of 240 F (120° C) -- Loading on all (4) sides of press.Overall dimensions: Length 165" x 81" x 117-1/4"

Simonds Band saw leveler. Comes with pallet of spare parts.

Morgan Unscrambler - Hydraulic Drive Cant Chop Saw - 20" Blades, 6"x9" Capacity, 10 HP Motor, Pneumatic Cycle, Fixed Stop Smith Resaw - 15 HP Motor, 13'2" x 1.25" Bands, variable feed speed - MISSING drive motor and gearbox for the feed belt. Includes: Powered infeed conveyor leading to the resaw with VFD. Machine required 480v/3Ph for saws, 240v/1Ph for VFD units and controls. All control contacts are contained in a single box. All wires were labeled upon removal.

SNX nVISION System2 G2 CONTOUR EDGEBANDER + Optional Dual Telescoping Arms for simultaneous Contour Banding & Trimming: -- Specifications: Curved (Contour) Edgebander to allow 360° edgebanding to contoured (shaped) panels.Edgebanding is applied automatically as part is advanced past the edgebanding workstations via turntable.Reduced learning curve/expertise for operation as operator simply loads part to vacuum turntable, then activates the edgebanding cycle. -- Working Capacity: The nVision Contour Bander can band a minimum material size of 150 mm (6") diameter.Maximum material size 2,400 x 2,400 mm (94" x 94"); Maximum material weight up to 104.5 KG (230 LBS).Material thickness from 10 - 60 mm (0.4" - 2.36"); Banding thickness from 0.5 mm thin tape w/low temp adhesive - 3mm tape. -- Radii Capacity:Minimum Internal (inside) radius 80 mm (3.14"); minimum external (outside) radius 30 mm (1'18") based on 1 mm thick edge tape. &#9679 Edgebanding thickness 1 mm, min = R 30 mm &#9679 Edge thickness 2 mm, min = R 50 mm &#9679 Edge thickness 3 mm, min = R 80 mm &#9679 Panel thickness 10-60 mm with edge thickness 1 mm &#9679 Panel thickness 10-60 mm with edge thickness 2 mm &#9679 Panel thickness 10-45 mm with edge thickness 3 mmIMPORTANT: ALL minimum & maximum radii are affected by tape thickness, quality of adhesive and edgebanding being applied. Radius size dramatically affected by adhesive temperature and quality of edge tape, semi or rigid. -- Equipped with:(1) Thermal-regulated glue pot heated via (2) 800-Watt heating elements with electronic temperature controls; holds up to 1 KG (2.2 LBS) of granules. (2) Pressure rollers to copy the shape of the piece, automatic guillotine for coiled material up to 3 mm (0.11") thickness & 57 mm height (0.125" - 2.25"). -- Features: TRIAX 3-AXIS Laser System (patented) for tighter butt joints & easy length identification with closed parts without the need for additional length measurement.The Laser also detects a tight radius and will automatically slow the speed + resume the set speed when the detected radius has passed.The machine is also equipped with the foot pedal for manual control/intervention. Motorized turntable for automated edgebanding application to large panels.(2) "Heavy Duty" Articulating arms to support the parts during edgebanding and trimming. Arm has a large inter-changeable vacuum pod to secure panels during edging and trimming.NOTE: Panels can be irregular in shape but must conform to the min. tolerances of inner & outer radii and fit within the work area. -- Complete with: &#9679 Top & Bottom Trimming unit &#9679 Centralized control panel with Simple PLC Touchscreen Interface with individual controls for all stations to enable manual feeding of panels if desired &#9679 Banding station &#9679 Edgeband coil stand &#9679 Standard-size vacuum pod for articulated arm &#9679 80 mm dia. (3") dust extraction outlet &#9679 Foot pedal activation/de-activation control &#9679 Larger feed roller

SNX nVISION SYSTEM G1 SEMI-AUTOMATIC CONTOUR EDGEBANDER: -- Specifications: Curved (Contour) Edgebander to allow 360° edgebanding to contoured (shaped) panels.Edgebanding is applied automatically as part is advanced past the edgebanding workstations via turntable.Reduced learning curve/expertise for operation as operator simply loads part to vacuum turntable, then activates the edgebanding cycle. -- Working Capacity: The nVision 1 can band Minimum material size 150 mm (6") diameter.Maximum material size 2,400 x 2,400 mm (94" x 94"); Maximum material weight up to 104.5 KG (230 lbs).Material thickness from 10 - 60 mm (0.4" - 2.36"); Banding thickness from 0.5 mm thin tape w/low temp adhesive - 3mm tape. -- Radii Capacity:Minimum Internal (inside) radius 80 mm (3.14"); minimum external (outside) radius 30 mm (1.18") based on 1 mm thick edge tape. &#9679 Edgebanding thickness 1 mm, min = R 30 mm &#9679 Edge thickness 2 mm, min = R 50 mm &#9679 Edge thickness 3 mm, min = R 80 mm &#9679 Panel thickness 10-60 mm with edge thickness 1 mm &#9679 Panel thickness 10-60 mm with edge thickness 2 mm &#9679 Panel thickness 10-45 mm with edge thickness 3 mmIMPORTANT: ALL minimum & maximum radii are affected by tape thickness, quality of adhesive and edgebanding being applied. Radius size dramatically affected by adhesive temperature and quality of edge tape; semi or rigid.Equipped with:Thermal-regulated glue pot heated via (2) 800 Watt heating elements with electronic temperature controls; holds up to 1 kG (2.2 Lbs) of granules. (2) Pressure rollers to copy the shape of the piece, automatic guillotine for coiled material up to 3 mm (0.11") thickness & 57 mm height (0.125" - 2.25"). Features: -- Laser for easy length identification with closed parts without the need for additional length measurement.The Laser also detects a tight radius and will automatically slow the speed + resume the set speed when the detected radius has passed.The machine is also equipped with the foot pedal for manual control/intervention. Motorized turntable for automated edgebanding application to large panels.Holding or support arm has a large inter-changeable vacuum pod to secure panels for edging and trimming.NOTE: Panels can be irregular in shape but must conform to the min. tolerances of inner & outer radii and fit within the work area.Complete with: &#9679 Top & Bottom Trimming unit &#9679 Centralized control panel with individual controls for all stations to enable manual feeding of panels if desired &#9679 Banding station &#9679 Edgeband coil stand &#9679 Standard-size vacuum pod for articulated arm &#9679 80 mm dia. (3") dust extraction outlet &#9679 Foot pedal activation/de-activation control &#9679 Larger feed roller &#9679 QC Glue tank with sensor. -- Actual Model is SNX nVISION SYSTEM G1

SNX NVISION SYSTEM2 CONTOUR EDGEBANDER: -- Specifications: Curved (Contour) Edgebander to allow 360° edgebanding to contoured (shaped) panels.Edgebanding is applied automatically as part is advanced past the edgebanding workstations via turntable.Reduced learning curve/expertise for operation as Operator simply loads part to vacuum turntable, then activates the edgebanding cycle. -- Working Capacity: The "nVision" Contour Bander can band a minimum material size of 150 mm (6") diameter.Max. material size of 2,400 x 2,400 mm (94" x 94"); max. material weight up to 104.5 kG (230 Lbs).Material thickness from 10 - 60 mm (0.4" - 2.36"); banding thickness from 0.5 mm thin tape w/low temp adhesive - 3 mm tape. -- Radii Capacity:Minimum internal (inside) radius of 80 mm (3.14"); minimum external (outside) radius of 30 mm (1'18") based on 1 mm thick edge tape. &#9679 Edgebanding thickness 1 mm, min = R 30 mm &#9679 Edge thickness 2 mm, min = R 50 mm &#9679 Edge thickness 3 mm, min = R 80 mm &#9679 Panel thickness 10-60 mm with edge thickness 1 mm &#9679 Panel thickness 10-60 mm with edge thickness 2 mm &#9679 Panel thickness 10-45 mm with edge thickness 3 mmIMPORTANT: ALL minimum & maximum radii are affected by tape thickness, quality of adhesive and edgebanding being applied. Radius size dramatically affected by adhesive temperature and quality of edge tape, semi or rigid. -- Equipped with:(1) NEW Thermal-regulated glue pot heated via (2) 800-Watt heating elements with electronic temperature controls; holds up to 1 KG (2.2 LBS) of granules. (2) Pressure rollers to copy the shape of the piece, automatic guillotine for coiled material up to 3 mm (0.11") thickness & 57 mm height (0.125" - 2.25"). -- Features: TRIAX 3-AXIS Laser System (patented) for tighter butt joints & easy length identification with closed parts without the need for additional length measurement.The Laser also detects a tight radius and will automatically slow the speed + resume the set speed when the detected radius has passed.The machine is also equipped with the foot pedal for manual control/intervention. Motorized turntable for automated edgebanding application to large panels.(2) "Heavy Duty" Articulating arms to support the parts during edgebanding and trimming & to maximize production throughput. Arm has a large inter-changeable vacuum pod to secure panels during edging and trimming. NOTE: Panels can be irregular in shape but must conform to the min. tolerances of inner & outer radii and fit within the work area. -- Complete with: &#9679 Top & Bottom Trimming unit &#9679 Centralized control panel with Simple PLC Touchscreen Interface with individual controls for all stations to enable manual feeding of panels if desired &#9679 Banding station &#9679 Edgeband coil stand &#9679 Standard-size vacuum pod for articulated arm &#9679 80 mm dia. (3") dust extraction outlet &#9679 Foot pedal activation/de-activation control &#9679 Larger feed roller &#9679 QC Glue tank with sensor.

SNX - Coil Hub, ...Edgebanding Heater & Storage System: For straight-line and contour Edgebanders - Keeps banding at the perfect temperature. - Softens banding, making it more pliable. - Keeps banding at the perfect temperature. - Softens banding, making it more pliable. - Increases adhesion. - Decreases delamination issues. - Allows a cleaner guillotine cut. - Lessens the chance of chipping when trimming. This "CoilHub" also keeps the coils contamination-free, keeps the edgebanding easily accessible right at the machine, and can store up to (20) coils.

Combination Differential/Filling Machine SMARTCOATER with: 880 mm (34-1/2") Working/pass-through height; one of the best units ever produced. Dual purpose machine can be utilized as: -- 1) A standard differential Roll Coater for application of UV sealer or top coat material; as a differential Roll Coater the 1st application head is independently utilized to for precisely controlled application. -- 2) A Filling Machine for application of H2O or UV filling material to calibrate substrates with porous veneer; as a Filling Machine, both heads are utilized for application and reverse smoothing or pressing of UV filling material.Specifications: -- (2) Heads, 53" width cap. - 1st Head: 250 mm (9-3/4") Dia. rubber coated applicator roller with separate doctor roller; doctor blades are oscillating. -- 2nd Head: 245 mm (9-5/8") Dia. chromium coated smoothing/reverse roller w/separate chromium doctor roll; all heads are floating to compensate for calibration errors & minimize damages from oversize parts. -- Adjustable opening 0 - 100 mm (3-3/4"); thickness protection safety bar connected to pneumatic emergency lifting; EX-proof electrics on all motors. -- 2 HP Conveyor drive: Variable feed speed from 26 - 131 FPM; 1/2 HP variable RPM drive on doctor rolls and separate 3/4 HP drive on applicator & reverse rollers. -- Electrical power: 480 V, 3-Ph, 3.8 kW; 7 Amps.

SORBINI TM/95-2F Flow Coater Specifications: -- 24" Coating width, 4" max. thickness, hand crank controls curtain thickness, (1) head gravity feed. -- 2 HP feed motor for variable feed speed from 90 - 350 FPM, (1) 1.5 HP circulating pumps, (1) stainless steel tank & return reservoir. -- Conveyor: 24" Wide, 60" Long at infeed, 72" long at outfeed. 34" long center belt.

SORBINI MR1TFF26420 Single Head Differential Roll Coater;SORBINI Single head differential Roll Coater, 51" width cap., all functions PLC controlled.Specifications: -- (1) 9.8" Dia. applicator roll. -- (1) 6.8" Dia. hard chromed doctor rolls. -- Chromed wiper blades with precision control on applicator & doctor rolls. -- 1 HP Motor with AC inverter control on applicator rolls, 0.5 HP motor with AC inverter, speed control on all rolls. -- 3-15/16" Part thickness opening with dial indicator readouts mounted in both hand wheels, "quick change" feature of applicator rolls. -- Variable conveyor feed speed from 20 - 80 FPM, 1 HP AC inverted control for speed control. Complete with: -- Fluid pump with automatic low-level fill, return trough.