Woodworking Equipment For Sale

WYSONG & MILES - 291, ...Stroke Sander (Manual)5 HP - 1,200 RPM Motor; roller table size: 32" x 84"; horizontal travel stroke: 38"; adjustable height of table base from 26" to 35" via large hand wheel. -- Rubber-faced aluminum pullies, 8-1/2" face x 16" dia.; accepts 6" wide abrasive sanding belts.Pulleys can be spaced to accommodate various belt & material sizes; belt loop travels over table with manual handwheel belt tension & tracking. -- Includes: Magnetic starter, dust hoods

WYSONG & MILES 604 DOUBLE SIDED OSCILLATING EDGE SANDERDouble Sided Oscilating Edge Sander with 7.5 HP - 1,800 RPM TEFC motor; (2) 11" x 60" cast iron platens; 10" x 172" abrasive belt size, (150) oscillations/Min with 1/2" movement, 0.5 HP oscillation motor.Equipped with: -- (2) 11-1/2" x 62" Cast iron side tables and (1) cast iron end table; tables tilt 30° up & 45° down; 5" vertical table travel w/hand wheel adjustment, 5" lateral side table travel w/hand wheel adjustment, 4-1/2" lateral end table travel w/handwheel adjustment. -- 10" Dia. x 10-1/2" face direct drive pulley, 4-1/2" dia. x 10-1/2" idle pulley. Complete with: -- Magnetic controls with overload protection & dust hood with 4" dia. outlet.

Used YAMAMOTO 30-opening, premium quality, Plywood Hot Press. -- 500 Tons pressing capacity. -- Daylight is 4.7"(120mm). -- Press plates are 54" x 108" x 1.5" (1,370 x 2,700 x 40 mm). -- Auto loader feeds charger using pusher arm to load press. -- Pie rack with automatic unloader. -- Hydraulic system with accumulation tank. -- Heated by steam. -- Professional removal and loading available at Buyer's cost.

Used YAMAMOTO 45-opening, premium quality, Plywood Hot Press. -- 500 Tons Pressure Capacity. -- Daylight is 2.75" (70 mm). -- Press Platens are 106" x 53" x 1.57" (2,700 x 1,350 x 40 mm). -- Auto loader feeds charger using pusher arm to load press. -- Pie rack with automatic unloader. -- Hydraulic system with accumulation tank. -- Heated by steam. -- This particular press was only operated for about 1-1/2 years. -- Professional removal and loading available at Buyer's cost.

Yaskawa Motoman UP50N Robot YR-UP50N-A00 Payload 50kg Control Box Teach Pendant Yaskawa Motoman UP50N Robot Type: YR-UP50N-A00 Payload 50kg

A20 YATES PLANER, Complete line w/16’ Trimmer

Yates A20-12 Planer Infeed Deck Tilt Hoist 575 V Includes: Misc parts, heads and attachments for S4S and T&G. This system was removed from service this Spring. It is ready to load.

YATES AMERICAN A95 Planer Matcher - 20 knife machine. Features fabricated frame with 100 HP top head, 75 HP bottom head, setworks for top head and left side head, hydraulic powered feed rolls, removable heads on all spindles, dynamic press roll tensioning, PLC control, chromed and water cooled beds, electronic cutter head brakes, high capacity hydraulic pump unit, operators console, side head setup stand, spare top and bottom heads, motor control center.

YATES AMERICAN B-26 Top & Bottom Rough Lumber Planer24" x 4" Opening cap., 3/4" to 4" thickness capacity; 46" minimum unbutted length capacity;Specifications: -- (1) 75 HP DMD motor power hoisted top head, (1) 40 HP DMD motor bottom head, 8" dia. cutting circle at 3,450 RPM. -- 40 HP Hydraulic power unit for variable feed rate from 75 to 400 FPM, 12" dia. Urethane tire top feed rolls, 12" dia. non-powered lower rolls. Equipped with: -- Carbide spiral cutterheads, automatic pressure bar release (hydraulically operated), hydraulic top & bottom headlocks, anti-lap bar device, air tensioned & released chipbreaker. -- Complete with: Built-in top & bottom jointers, dust hoods, electrically interlocked safety guards, and small remote operator's console.

There are two of these systems available. They were recently removed from the current operation and available immediately.

Yates-American A-20 planer. 4 sided with profile machine, 10" rolls. Includes 10 cylinder Detroit engine, belt drive assembly.

The frame is a massive, compact and solid casting which takes less floor space for its capacity The feed drive is built to stand up under the hardest kind of services The feed rolls are of such design that the advantages of the open side type of construction are combined with of the advantages of the inside The top and bottom head assemblies are of the most substantial construction The top head chip breaker is made of chilled cast iron section, each section being spring loaded and adjustable The side head spindles are short and of large diameter The side head chipbreaker moves in and out with the head and is also provided with an additional screw adjustment for close setting The bedding is continuous throughout the entire length of the machine

Yates American E-12 End Matcher System for tongue and groove flooring includes: Belt, Straight Line Blade, 3-blades, Infeed conveyor to end matcher, transfer conveyor from first machine to second machine, variable speed outfeed conveyor

Yates American B-15 Helical Head Planer S/N 29658

Used Yates American Model B-26, 24” Double Planer, 75HP top, 40HPBottom, top and bottom 10 knife cutterheads, on the fly top and bottom jointers, 3 phase 480volt electrics, slide out lower cutterhead, top fixed cutterhead, 3-3/4” thickness capacity, approx. 20HP hydraulic feed works, power bed raise and lower, sectional pneumatic chip breaker, top infeed/outfeed rubber rollers.

Yates American No 50 #20376 - Setup stand - Good condition Call 800-459-2148 for more info.

Planer Head Set Up Stand

ZEETECH - 200, ...Universal Hopper Feeder that can be mounted to all Moulders. - Capacity: 3/4" - 9-1/2" width, 0.38" - 5" max. material height, 10" min. length. -- Oil-free air operated drive unit mounted on THOMPSON hardened ways, damped drive travel, positive sensing sequencing actuator. -- Variable speed range from 0 - 120 FPM @ 80 - 120 PSI. -- Includes: All air logic controls (no power required) and air filters; easy to install.

ZUCKERMANN CHALLEGER Copy Lathe w/Sander for asymmetric/irregular shaped parts.Hopper feed, single spindle; approx. 149" (3,800 mm) max. between centers, 8-13/16" (250 mm) max. part dia.; 5 HP cutter head motor at 6,000 RPM, oscillating belt sanding unit, both units work together. -- 'Cup' style Cutter head; 2 HP spindle & pattern rotation motor; mechanical & pneumatic traverse of cutter head and sanding carriage. -- Complete with: Built-in operator push button control panel and overhead dust collector hood.