Equipment For Sale

Transfer Belt Built on Mellott rollcase frame • 31" x 12' spiral rollcase built on end • 36" x 25' x 8" sides • 22" pan, 22"

Mellott Vibratory Conveyor Includes drive unit and motor

Mellott #5 Log Turner

Mellott #5 Log Turner

30' L, hyd drive, 24" pan, 8" sides, 19" from floor to bottom of pan, good condition

slab drag, 15' x 15', electric gearbox drive, 81X chain with steel cleats bolted on, good working condition

roll case, 24" wide x 43' long, electric drive, comes in 2 sections, includes spiral section and board stop, very good condition

Mellott # 5 Log Turner

Mellott Log Turner, chain type

Mellott Hyd Unit

30' L, hyd drive, 17" pan, 4" sides, good condition

Mellott Log Turner

Mellott #5 Log Turner

Mellott shaker table, 16' wide x 6' long, hyd drive, excellent condition

Mellott #5 Log Turner

The seller has confirmed that this Mereen Johnson 441 Rip saw is in great working/running cnodition and it is ready to load! - 2004 Cameron Auto Opti-Rip Infeed - Model: 34F-M1 - Serial: OR164 - 100% Servo (only Servo is this Cameron) - Full amp load 81 - 44" W bed - Up to 20 saws can be run on the arbor - No moving blades BUT there are moving lasers Although this one has been pulled from service, they have an identical one still running and available for inspection....

Mereen-Johnson Model 441-DC Gang Rip Saw Capacity: Arbor space 41” Arbor Drive: 75 HP 3600 RPM TEFC motor Feed Drive: HP TEFC variable speed direct; 45’ to 225’ feet per minute Hold Downs & Bed Plate: Four 5” dia. Air loaded high yield idle press rolls Saw Sleeve: One 41” capacity sleeve Dust Collection: Four upper dust pick-ups: two (2) 8” dia., two(2) 4” dia., one lower 4”dia. Pick-up:(requires total 4820 CFM @ 5,000 feet per minute) Swing Arm & Tip-Up Cart: One floor mounted dual shaft swing arm and one tip-up saw sleeve set-up cart Electrical: Arranged for 3 phase, 60 cycle, 460V Cameron Automated Opti-Rip Model #34F-M1 System: Manufacture Year: (2004) Complete with length measurement Tally System 5 infeed belt and chains for feeding a Gang Rip saw up to 41” wide 16 width sensors 3 sets of pinch rolls for short stock 1 fixed & 4 movable laser lights This system feed for 4’ to 16’ max lumber length It feeds from operator right to left Wired 220V; If 440V required, a transformer will be needed

Mereen Johnson Model 312 Rip Saw Includes: New pads for the chain Includes: Twistlock Collar Mounted Saw Blades Available approx May 1, 2024

Mereen Johnson Model 312 DC SR1R Rip Saw 600 V/3 PH/60 Cy

MEREEN-JOHNSON Model 524-DDCSR 2+4 Double Arbor Gang Rip SawSPECIFICATIONS: -- First Arbor Arranged with Two (2) Independently Adjustable Select Saw Assemblies for Mounting Hogging Blades -- Second Arbor with Four (4) Independently Adjustable Select Saw Assemblies -- Arbor Space 24" -- Thickness Capacity to 1-3/4" with 12" Tooling and 2-3/4" Using 14" Tooling -- Minimum Length 30"Equipped with & Features -- Two (2) M-J Direct Drive Motors 75 HP Each -- Feed Motor 7.5 HP TEFC, 30' to 235' rate with Frequency Inverter Speed Control -- Saw Set Up for Second Party Optimizing System.