Woodworking Equipment For Sale

The K14 Series system is a small, heavy-duty, bench-top, barrel tumbler with standard capacities ranging from 0.75 - 1.5 cubic feet. -- The K14 system is a deburring machine solution that features a timer, variable speed, a heavy chain drive, and removable, interchangeable barrels. -- The barrels are mounted high enought to allow a screen and pan underneath so the barrel can be emptied without lifting and dumping. -- This deburring turn-key machine can handle loads of up to 200 Lbs. The barrels are mounted in a cradle and can be interchanged to divide up the load. -- (1) Steel barrel lined with a durable Polyurethane lining; 14" diameter across corners by 22-1/2" wide; Quick action lock on covers, solid, watertight doors. -- Variable speed control 25 - 50 RPM; 24-Hour timer; Start-stop switch. -- Complete bench-top unit dimensions are 44-1/2" W x 25" D x 24" H.

Pneumatic Single Spindle Tabletop continuous operation drill;Specifications: -- 1.25 HP direct drive pneumatic motor; 8" tabletop working height; 1 Sec cycle time. -- Drills the pocket hole with a 3/8" dia. step bit in (1) smooth operation; the bit is supported all the way to the workpiece by a hardened steel drill guide that ensures tear-out free holes and consistent placement in virtually any material. -- Capacity: Materials from 1/2"- to 1-1/2" thick.Features: -- Pneumatic drill motor, pneumatic clamping. -- 15° Boring angle for greater stability, reduced screw breakout & splitting; this produces a smaller "flat-bottom" pocket hole with rounded sides that can be plugged with a dowel if desired.Includes: -- External regulator, filter & lubricator, 3/8" cobalt drill bit, and foot pedal actuation.Requires a compressor able to produce 8 CFM at 120 PSI (50% duty cycle).

KREG DK 3100 Pocket Hole Boring MachineElectric 3-spindle Pocket Drill; 1.5 HP direct drive electric motor; 39-1/2" table/ top working height; (0.5 - 1) Sec cycle time. -- Drills (2) pocket holes in (1) machining cycle across rails of varying widths with 3/8" dia. step bit in (1) smooth operation.... Drill spindles in the machine are fixed at 3/4" - 1" and 1-3/4" on center allowing it to handle most common rail widths of 1-1/2" up to 3-3/4" with ease. -- One of the (3) Spindles is with left-handed, simply remove one bit from the spindle not being used to set the desired 2-hole spacing. -- The bits are supported all the way to the workpiece by a hardened steel drill guide that ensures tear-out free holes and consistent placement in virtually any material. -- Features: 15° Boring angle for greater stability, reduced screw breakout & splitting. This produces a smaller "flat-bottom" pocket hole with rounded sides that can be plugged with a dowel if desired. -- Includes: Pressure gauge & cycle counter, fence, holddown & clamping assembly, (2) 3/8" cobalt drill bits, and foot pedal control.

Electric Single Spindle Pocket Drill. Specifications: -- Capacity: Materials from 1/2"- to 1 1/2"-thick. -- 1.5 HP direct drive electric motor (also available 1.5 HP direct drive pneumatic motor); 40" table top working height; 1 Sec cycle time. -- Drills the pocket hole with a 3/8" dia. step bit in (1) smooth operation. The bit is supported all the way to the workpiece by a hardened steel drill guide that ensures tear-out free holes and consistent placement in virtually any material. -- Electrical: 110 VAC, Pneumatics: 90 PSI, recommended for clamping. -- Dimensions: 50"H x 24"W x 24"D (40" table height), 176 lbs.Features: -- 15° Boring angle for greater stability, reduced screw breakout & splitting. -- This produces a smaller "flat bottom" pocket hole with rounded sides that can be plugged with a dowel if desired. Includes: -- Pressure gauge & cycle counter, fence, holddown tower, (1) 3/8" cobalt drill bits, and foot pedal actuation.

Pneumatic Single Spindle Pocket Drill;Specifications: -- 1.25 HP direct drive pneumatic motor; 40" table top working height; (0.5 - 1) Sec cycle time. -- Drills the pocket hole with a 3/8" dia. step bit in (1) smooth operation. -- The bit is supported all the way to the workpiece by a hardened steel drill guide that ensures tear-out free holes and consistent placement in virtually any material. Pneumatics: 120 PSI recommended. Features: -- 15° Boring angle for greater stability, reduced screw breakout & splitting. This produces a smaller "flat-bottom" pocket hole with rounded sides that can be plugged with a dowel if desired. Includes: -- External regulator, filter & lubricator, (1) 3/8" cobalt drill bit, and foot pedal actuation. Just add $150 to the price of the machine for shipping.

KUFO SK-12RS Straight Line Rip Saw w/Return Conveyor;Entry level Straight-Line Rip Saw with a guaranteed 6' glue line. -- Powered by a 15 HP direct drive motor. -- 12" Dia. Blade capacity for up to 3-1/4" max. cutting height, 4,200 RPM blade speed. -- Equipped with (6) holddowns and a Wye-Delta soft start for lower amp requirements during start-up. -- 1 HP Feed motor, 36 - 145 FPM feed speed, 6" chain width and automatic chain lubrication. -- Treated chain links, pins and raceways withstand heavy use because of an automatic oiler. -- Large 15-3/4" rip capacity. -- Overarm control box mounted on the in-feed side. -- Total space requirements are about the same as a standard size tablesaw. -- Complete with side mounted return conveyor.

Oscillating Edge Sander with end sanding kit. -- 6" Wide x 89" long abrasive belt. -- Tilting 6" x 24" platen. -- 3 HP, single or 3-Phase motor w/emergency switch. -- 6" Diameter drive pulley. -- 8" x 24" Front table with a 4" vertical adjustment and miter gauge. -- End table for radius work. -- Heavy tables, fabricated steel base and dust hood. -- 3-Phase unit model # is SK-3000SDN3.

Single belt oscillating "Tiltable Bed" 0° - 90° sander, 3 HP main motor, 3,400 RPM, belt size 6" x 89", 30.5" long platen. -- Max sanding length 30.5", 4" vertical adjustment of front table, 36" table height, oscillating rate of 121 times/min. -- Includes: (4) interchangable spindles, sizes are 1.25" - 1.5" - 2" & 2.5" dia.

Kuka KR60-3 Robot System KR C4 Control System Kuka Programming Smart Pad Robot Enclosure (3) Heave duty conveyor racks

KUNDIG DUPLEX 53-RC-E Wide Belt Sander (2) Heads; 52" Width cap. Drum, Combination Head.Head Configuration1st Head: 7-1/4" Dia. rubber covered contact roll, 25 HP motor.2nd Head: Combination head with rubber covered contact roll and segmented finishing platen, infeed sensors sense the panel and electronically control the platen height with timers, variable edge control can also be set, 20 HP motor.Specifications: Abrasive belt size 54" x 75" with air tensioning and electronic abrasive belt tracking, both heads with abrasive grit thickness adjustment, 2 HP Variable feed drive. -- Conveyor belt speeds 9 - 45 FPM, controlled by electronic inverter & adjustable on the control panel; infeed & outfeed rubber covered holddown rollers.Equipped with & Features: -- Workpiece thickness cap. 1/8" - 6-1/4", motorized thickness adjustment with LED readout. -- A joystick controls the conveyor opening and start/stop of the feed, automatic "over-thickness" protection and automatic conveyor belt tracking. -- Constant passline of conveyor height at 35". -- Air blow off of second head abrasive belt. -- Emergency stop button, motor load meters, magnetic controls.NOTE from the seller: There is a small leak in the air bladder . The sander has 6,541 working hours

Max. operating width in grain direction approx. 3200 mm Min. operating width in grain direction approx. 600 mm Width of the veneer strips across the grain from approx. 60 mm Veneer thickness approx. 0.3 – 2.5 mm Capacity up to 28 joints/min. Feed speed approx. 30 m/min. Operating voltage 480 V, 3 Ph, 60 cycles

LA NUOVA SCOLPITRICE 201-16 Multi-Spindle Carving Machine.(16) Cutter Stations, 55" max. workpiece length,Specifications: -- (16) Dual carving spindle heads, 8" between spindles, 20" max. working diameter. -- Each head has a roughing & finishing spindle, all heads swivel 360° with pneumatic locking. -- Upper carriage controlled by (2) High Frequency changers allowing (2) motor speeds of 12,000 & 18,000 RPM. -- Pneumatic chucking of material, stock turns 360°. Copy stylus of hardened and ground steel, adjustable for depth on either side. -- Traverse feed of carving heads was patented and requires no maintenance. -- Includes: Lot of tooling. Table for flat/horizontal copying.Note: Machine completely gone over and all heads rebuilt in 2011 and used sparingly since.Actual model is 201-16.

V2000 60 x96TS-1VL-ONS-OCE-06PS Transportation Simulator Performs both rotary and vertical motions Designed for testing larger crates up to 60-in. by 96-in

LACEY-HARMER E-LINE Self-contained Visible Diode Laser End ShooterEconomical self-contained Visible Diode Laser; optics housed in a sealed cell to provide added protection against contaminants and moisture; nickel plated housing. -- Specifications: 100 Millampere operating current, -20° - +40° C operating temperature, 90 V for 250 nano-Sec mechanical stock. Beam angle with 5 mW - 15 mW output, 636 nm wave length. -- Options: 36" Long Diode Array Stand adjustable up to 90° from mounting surface, lines move easily and parallel to each other, micro-adjustment to make lines parallel, no tools needed -- Projects a line from approx. 12' to 15' depending on area lighting -- Consisting of two parts; (1) crossbar style mounting bracket, please add...$ 143; (2) axis slide brackets for easy positioning, add...$ 125 each or alteratively a simple universal stationary mounting bracket add...$ 30.

LACEY-HARMER LD-2002 Diode LaserEconomical self-contained Visable Diode Laser, optics housed in a sealed cell to provide added protection against contaminants and moisture; nickel plated housing. -- Specifications: 100 Millampere operating current, -20° to +40° C operating temperature, 90 V for 250 nano-sec surge protection. Beam angle 5 to 90 degrees, 5mW to 35mW output, 636 nm wave length for lines up to 20' projection. -- Options: 36" Long Diode Array Stand adjustable up to 90° from mounting surface, lines move easily and parallel to each other, micro-adjustment to make lines parallel, no tools needed. -- Optional items consist of: Crossbar style mounting bracket, please add...$ 90; axis slide brackets for easy positioning, add...$ 125 or alteratively a simple universal stationary mounting bracket, please add...$ 30.

1- 5mm Boring and Inserting Unit with Vibratory Hopper 1-8mm Boring and Inserting Unit with Vibratory Hopper Power: 208v-220v, 3 Phase, 30 Amps 96? Maximum Work Zone 4 zone stops 3-Axis Control For Positioning Weight 6,000lbs Solid One-Piece Welded Tubular Steel Frame Footprint (L x W x H): 135? x 45? x 82? Shipping Dimensions (L x W x H): 42.3? x 49? x 43? Shipping Weight: 7500 lbs

Hot Air Edgebander for Preglued banding 0.4 - 1.5 mm thickness Automatic cutoff for up to 1/32" Coil feed with manual feed for strips Panel thickness 10-50mm Front and rear end trim Top/bottom trim

Laguna Bandt 4 Edgebander Machine is 6 months old Extremely low hours - Buyer upgraded to a larger machine!

Gantry Clearance: 12? Z Axis Travel: 13? Table Size: 4’x8' Working Area: 49?x97? Rapid Speed: 1,800 IPM Cutting Speed: 1,000 IPM Spindle HP: 12HP Spindle Speed: 6,000 – 24,000 RPM Cutting Time: 50 Hours Electrical: 208-230V/ 3PH Equipped With: 12 HP HSD Spindle 8 Position ISO 30 ATC Yaskawa AC Servos Drive Motors 6 Zone Vacuum Table Planetary Gear Box Drive System Tooling Kit Helical Rack & Pinion X/Y Axis Ball Screw Z Axis 10 HP Stock Regenerative Blower Vacuum Pump Syntec Industrial Control System Controller: B+R PP65 Stepper Package Footprint: 78?x127? Approx. Shipping Weight: 3,500 Lbs

Laguna Tools 51X75 Pro Widebelt Sander51" width cap. Drum, PlatenHead Configuration 1st Head: 8"; roller 30 HP ( Drives both heads )2nd Head : 4" Wide platenSpecifications : -- Main motor: 30HP -- Variable feed speed: 2HP -- Table lifting motor: 0.25HP -- Voltage: 220/3 PHASE -- (PLC) Programmable Logic Control --Automatic Thickness Control -- Max sanding height: 150mm/5.9″ -- Min sanding height: 1/4″ [6,4 mm] -- Max sanding width: 51″ [1300 mm] -- Sanding belt size: 51″ X 75″ [940 mm X 1905 mm] -- Adjustable sanding platen: 1-3/4″ inch [45 mm] -- Diameter of sanding drum: 8"; + 4"; -- Length of sanding drum: 51"; -- Sanding drum RPM: 1725 RPM -- Conveyor height at lowest setting: 32 inches [813 mm]Equipped with and Features -- Conveyor speed: 12-60 FPM, -- Dust port size: 4″ [100 mm] -- Number of dust ports 3 -- Foot print: 63"; X 65"; X 98"; -- Cabinet: Steel -- Operating air pressure: 6 Bar -- Operating air pressure: 6 Bar -- Sanding belt oscillation: Pneumatic/Adjustable -- Sanding belt motor break: Yes. Air operated disc break -- CSA: Fully Certified -- Net Weight:4200 Lbs. -- Ship Weight: 4450 Lbs.