Woodworking Equipment For Sale

SCM / DMC MB 90 WIDE BELT (50" - 90", 2-HEAD): -- Specifications:This machine has been designed to house and combine working units equipped with oscillating discs and brushing rollers, suitable for different sanding applications. -- Working Capacity: Width 53", Main Working Units 1-2-3 -- Oscillating Discs Unit: (19) -- Brushing Unit: 300 mm diameter -- Feed Conveyor: from 2 to 16 m/min -- Complete With: Variable feed drive and vacuum feed table.

156" long x 60" wide x 80" high (3) vertical pneumatic Clamping bars (7) clamps that can be placed horizontal or vertical on perforated surface

3/4 HP 1725 rpm motor 115/208/230 volt single phase approx. 12” x 30” table Jacobs chuck approx. 3/4” footpedal Assorted fixtures and tooling as pictured.

DEIMCO MFM-98 ACRYLIC COATING FINISHING SYSTEM: Drying Oven for the purpose of baking and drying the acrylic finish onto lumber and panel products. -- Specifications:3"; dia. x 21.625" long Rollers on 12"; centers; Infeed: 16' long In-feed Conveyor, 10' long Transfer Conveyor, 12' long Oven Conveyor: -- Operator & Machine Control:Built with Allen Bradley/Honeywell Components, MFM Serial: 1177, Voltage: 460V/60 Hz/25 Amp, Air: 1"; NPT 90PSIG. -- Complete With:Electrically Heated Oven; 8 Cool Down Fans; 2 - Hydraulic Lift Tables; Panel Machine with Hydraulic Pump; 15’ Flash Off Conveyor; 40’ Cool Down Conveyor Includes the following for (two) flood coat machines, Conveyor System, Arbors, Paint Pump, Hydraulic Pump, Hydraulic Lift Table -- Complete Over-all Foot Print 175’ long x 50’ wide

Custom-Built DEIMCO Through Feed Sprayer with a BLASDEL IR Preheat Tunnel that is available MARCH of 2023. Until then, the System can be seen in operation. -- Line was designed to preheat Fiber Cement board prior to painting and is followed by a Single-Arm Reciprocating Sprayer with 4-Spray Gun cap. Spray Guns not included.SEE ATTACHED VIDEO FOR A GOOD LOOK AT THE LINE's OPERATION!Built in 2019, the System was used for approx. (2) years; current owner changed their process and no longer requires the equipment.Oven width cap.: 60" Wide, 1-3/4" part height cap.; overall Oven dimension: 84" Wide x 12-1/2' long x 55" high, excluding the Blower & Stack. Line/Conveyor: Variable speed drive, 18.5 FPM to 26 FPM; Reciprocator operates up to 260 FPM and set by the HMI. 2-Zone Oven: -- Zone 1: (2) Upper left side wall/ceiling mounted; 18" x 60" emitters. -- Zone 2: (2) Right upper side wall/ceiling mounted 18" x 60" emitters; 8" clearance between emitters & rolls. Heaters: Natural gas using 7" WC; 480 Volt preheat; TC, FM, flange frame. - Gas Ratings: 360,000 BTUH Max. input ; 100,000 BTUH standby input; Air Exhaust on infeed & Injection Blower on outfeed. Electrical ratings: 26.6 Amps, 480 V - 3 Phase, 60 Hz.Exhaust: 980 CFM, 1 HP Motor.Control Panel: 60 AMP Disconnect switch, ALLEN-BRADLEY "Panel View Plus HM", IEC contactor & High Temp PID exhaust.NOTE: (25) New replacement conveyor rollers & (40) reconditioned rollers for IR Tunnel.DIEMCO Sprayer complete with: (1) Reciprocating Arm holds (4) guns and reads the leading & trailing edge to turn on & off the guns as the parts feed through; best to run full width loads through Sprayer; Overspray funnels into buckets.Spray Guns turn on & off based on the part leading & trailing edge; read by a light curtain on the infeed end.Dims: GFS Spray Cabin: 13' Deep x 8-1/2' wide x 9' high surround the reciprocating arm. - Filter & Exhaust Section: 13' Wide x 3' Deep x 10' High.

DEKKER - VMAX 10 HP: Vacuum Pump (Liquid Ring)(2) Used DEKKER 7.5 kW (10 HP); 60 Hz Vacuum Pumps; model: # VMX0153MA1-01.Nominal capacity (ACFM): 150. Max. Vacuum level 29 in. hg.; Oil capacity: 6-1/4 gallon; Pump Speed: 1,750 RPM.(2) Units Sold as a pair.NOTE: (1) Unit requires repairs.

DEKKER - VMAX - 40 HP VMX0553KA1-00 Vacuum Pump (Liquid Ring) 13,556 Hours40 HP Oil sealed; liquid ring; compact motor mounted Vacuum Pump System; 550 CFM; max. 29 inHg. -- Heavy-Duty ConstructionCompact design; small footprint. -- Direct Drive with:Low speed (1,750 RPM) Air-cooled design; low operating noise level; eliminates use of V-belts; results in very low maintenance; zero downtime over the full vacuum range without overheating.

DEKKER VMXO453KA1 - 25 HP Liquid Ring/ Oil Sealed Vacuum Pump: -- Specifications: 25 HP, 410 CFM rated cap. at max. 29" Hg; heavy duty construction, compact design, small footprint, patented. -- High-efficiency DX-5 separator eliminates oil carry-over concerns. Extended-life seal-fluid is not used as a lubricant. Change interval is not critical, resulting in a minimum of (10,000) Hrs. of continuous operation. -- Sturdy bearing pedestal mounts to standard NEMA, C-face motor. Direct drive low speed (1,750 RPM) eliminates the use of V-belts, resulting in very low maintenance and zero downtime. -- Continuous operation over the full vacuum range without overheating. Air cooled design and low operating noise level.

Delle Vedove 6 Lamp UV Arrangment: Bottom: Bottom: Top: Top: Right: Left Max. width: 8" wide 5 kw/lamp 30 kw total

2000 Delle Vedove SPL/11 linear sander with Bottom Sanding Unit 4 Sided sander brushing machine with: - Bottom Sanding Belt belt - Narrow Top Sanding Belt - Regular Top/Side Sanding Belts - Bottom Sanding Wheel / Brushes All wheels with automatic wear compensation / indexing Could use solid wheels or brushes

Delta 42-459 Shaper with Piwer Feeder Manufacturer Specifications( to be confirmed) 5HP 208-230/460V 3 Phase 1-1/4" Spindle Forward and Reverse switch 2 Speeds: 7,000 and 10,000 RPM Capacity under the nut: 5" Heavy duty Ritter fence, adjustable left and right sides Extra table wing drilled and threaded for feeder Table size w/extra wing: 27" X 40" 4" dust port Complete with Maggi power feeder. (2) available

Delta Table Saw 5 HP 230 volt 3-phase

Delta Radial Arm Saw

Delta Horizontal Boring Machine Model SP-131

Delta RC-63N 24" PLANER WITH SPIRAL CUTTER HEADSpecifications -- 24" x 9" Cap., 5/16" max. material removal, -- 10-1/2" min. part length. -- 15 HP Belt drive motor, -- Spiral Cutting Head -- 5,000 RPM, variable feed speed from 20 - 60 FPM.Equipped with & Features -- Powered raise and lower of 25" x 35" table, -- Sectional chipbreakers, sectional infeed roller & dual outfeed rollers. -- Push button magnetic control, -- Dust hood, & grinding attachment to sharpen helical head knives while on the machine.

DELTA 11-990C 12" 5-Speed Bench-Top Drill PressSpecifications: -- Table size 8-1/2" x 8-1/2" with 15-1/2"; x 40"; x 11/16"; Thick Plywood top, Table tilt 40° Left/Right. -- Base size 8-1/4" x 8-1/4". -- Quill travel 2-3/8", Chuck capacity 1/2", JT33 Spindle taper. -- Spindle speeds 620, 1,100, 1,720, 2,340, & 3,100 RPM.Equipped with: -- 1/3 HP - 1,720 RPM Motor.Complete with: -- Portable Wood Cabinet.Dimensions with cabinet: 41" x 36" x 57" H

DEPENDABLE - 203, ...Cold Press40" x 102" Cap., side loading on 102" sideSpecifications: (3) Split upper platens: 34" wide x 40" deep; split platens can be interlocked for single platen operation. 45" Max. daylight opening with 12" down stroke hydraulic cylinders. (6) Rows of pop-up rollers in machine bed for loading & unloading. (3) 7-3/4" Dia. hydraulic press cylinders from the top; (1) per platen. Hydraulic power pack with 10 HP motor mounted on floor at end of Press.

ADWOOD/DETEL - M29: Construction & Line Boring Machine (32 mm) Vertical/horizontal drilling: (29) Spindles; drills vertically from the bottom-up; horizontally from the back or any angle between 0° - 90°; tilting action of boring head is pneumatically controlled.Distance between the 1st & last spindle: 35.2"; max. boring depth: 3"; boring head with: (2) 2 HP - 2,800 RPM Motors; 44" x 21.4" table size.Complete with: (4) Pneumatic holddown cylinders; left- & right-hand side fences with: (2) Mechanical flip-stops & foot pedal control for clamping & boring cycle..

DETEL M-2H DOUBLE ROW LINE BORER.(2) Line boring heads of (25) spindles each on 32 mm centers, drills from the bottom up.Equipped with: -- (2) 2 HP motors drive spindles at 3,400 RPM. Hand crank adjusts the opening between heads from 5" - 25" w/mechanical digital readouts, drilling depth up to 2" -- Hardened steel gears that are pressed onto the spindle shafts, 120" back fence with (4) large flip-stops. -- (2) Pneumatic index pins with independent switches for sequence boring on long side panels. -- (2) Overhead pneumatic hold-downs. -- Complete with standard screw-in 10 mm collets; air/electrical controls, pneumatic oiler, and foot pedal actuator for clamping & boring cycle.Optional: Dust Collection on each head. Quick change collets.

Detel M-2H Boring Machine (2) 25-Spindle Boring Heads