Woodworking Equipment For Sale

MAKOR Q1 Spray Line including Paint Pumps and Guns:This line was set up with the idea of adding a stack oven after the sprayer in the future if it is required. This line has seen very little use.Station #1: Infeed loading conveyorStation #2: MAKOR Q1 paper belt sprayer 3 circuits plus a cleaning circuit.Station #3: Powered roller conveyorsStation #4 (3) three lamp UV oven. Station #5: Outfeed conveyor. The line comes with (2) two paint pumps and (4) four spray guns, the brands GRACO MERKUR and GRACO spray guns. Reciprocating Spray Machine, Makor Q-ONE 1300 with Changeover SystemFlexibility, reliability, and ease of use, combined with limited managing cost and investment, make Q-ONE the ideal machine for companies with low-volume production applying water-based or solvent-based paints, or glues. Even companies switching to automatic coating applications for the first time can realize the advantages of the Q-ONE: Higher production and paint savings, uniform coating, and higher and more consistent quality.Structure and Transport System:The single steel frame guarantees perfect stability and the absence of vibration during the oscillating spraying. A part reading bar is located at the entrance of the machine to detect the workpiece shape to optimize paint consumption. The workpiece transport system consists of a paper belt or plastic film supported by a vacuum belt system makes the machine self-cleaning, eliminating downtime and maintenance costs, but does not allow the recovery of the sprayed productoverspray is prevented from accumulating on the lower side of the workpiece paper roll replacement is quick and easy.Spraying Group:The guns, mounted to oscillating supports, are adjustable to allow optimal orientation of the spraying zone the entire oscillating group is connected to the frame of the machine through pads that guarantee the absolute absence of vibrations, resulting in perfect paint quality on the workpieces, the pressurization of the zone containing the oscillating mechanisms extends its life and requires little maintenance.Four (4) guns can be connected to one of the three (3) coating circuits three (3) high-pressure circuits with recycle for coatings one (1) high-pressure circuit (without return) for solvent. Coating circuits have return hoses for quickly washing the circuit and for the recirculation of paint-standard supply provides two (2) gun holding plates with a quick disconnection system to allow for fast replacement of the spraying unit.Paper Unrolling and Rewinding System:The unrolling system at the entrance and the rewinding device at the exit are designed to maintain constant tension of the paper, avoiding breakage even when it is soaked by the paint, loading and unloading the support rolls are easy due to lateral pull out on wheeled carriers. An independent vacuum hold-down fan enables superior control of the paper belt rewind station and includes a self-adjusting system to maintain a consistently flat paper belt transport (

MAKOR Q-ONE - Feed Through Spray Machine. -- The Q-ONE Sprayer. Single Arm Reciprocating System with: Paper belt overspray collection; it combines: Productivity, flexibility, and quick changeover with a limited investment. -- This continuous belt Conveyor System, combined with disposable paper promotes: "Self-cleaning" machine; dramatically reduces cleanup & service time.Operation -- Suitable for all types of: Conventional coatings from solvent to water-based materials. -- Conveyor advances only when parts are present. -- PAPERBELT Conveyor System with: Vacuum belt to secure & support the feeding of the disposable paper; ensuring proper tracking & automatic winding of the paper roll. -- The paper roll changeover time: Only a few minutes. The panel: Lies flat on the belt, which prevents the transfer of overspray onto the bottom side. -- Spraying enclosure is pressurized via: (2) Intake fans and filtered by means of dry filters. -- This System allows: Clean air & maintains a consistent airflow throughout the Spray Cabin; also limiting the machine maintenance time to a minimum and producing an enhanced quality finish, control & containment of overspray, resulting in significant material economy. - Internal airflow is adjustable utilizing inverters. -- Spray System uses: Inverter drive; variable speed reciprocating trolley, which provides a consistent spray speed & pattern across the entire conveyor belt. Equipped with Spray System: (4) Spray guns; mounted on a "Quick-Change" gun support trolley. -- (2) High-pressure lacquer feeding circuits with: Recycle through a fluid distribution manifold (predisposed for [2] additional lacquer feeding circuits). -- PLC Touchscreen for: Clear visual operator interface; large memory storage of: Working programs; parameters; controls; diagnostic functions.Photo diode light bar reads: Location & size of part to be sprayed.Technical Specifications -- Working width: 0 - 1,300 mm (0" - 51"). -- Feed Motor: 0.75 kW; variable speed control from: 2.5 - to 5 MPM (8 - 16 FPM). -- Vacuum belt motor: 1.5 kW (2 HP). -- Paper Rewind Motor: 0.18 kW. -- Paper Roll: Dia. 21-1/2" max. (approx. 9,500 linear ft.). -- Reciprocator motor: 2.2 kW. -- Exhaust fan motor: 5.5 kW. -- Air Flow: 7,950 CFM. -- Pressurization air: 2 x 3,900 CFM. -- Total installed power: 13 kW.NOTE: Really still "Like New" with Very Low hours! It is probably still the original roll of paper on the machine!

ROTOFAST 10 Panel Cleaner is designed for automatic cleaning of parts just prior to coating application for a dust-free finish. A rotating brush is combined with air blow-off units and an anti-static bar in order to efficiently clean flat or profiled parts of different shapes and dimensions. KEY FEATURES --Top surface One rotating brush with variable speed and height adjustment -- One de-ionizing (anti-static) bar -- One group of rotary blowers with timed entry -- One group of fixed blower nozzles with timed entry Bottom surface. -- One group of fixed blower nozzles with timed entry ÷ All components housed in single cabinet with suction hoods -- Feed speed adjustable by potentiometer -- Rubber pressure rollers to secure parts while brushing -- Belt conveyorWeight 600 Kg.

MAKOR Model 5-TC Profile Sander(5) Station machine, 7-7/8"" max. width & 3-1/8" thickness capacity. Equipped with: (4) Disc type sanding spindles, each with 4 HP direct motor drive, 6" spindle length, tilting 0 - 90ø and adjustable up & down on dovetail slides, automatic wear compensation; (1) top mounted abrasive belt sanding unit, for 7-7/8" wide belts. 30 - 150 FPM variable feed speed with (3) small 6" wide x 20" long conveyor belts placed between the sanding heads, with a common feed drive; adjustable overhead holddown wheels between the heads. All heads, wheels, and the feed belt are functioning as they should. Seller is including a large collection of spare sanding heads, wheels, and specialized tooling. These spares alone save you thousands in future maintenance and setup costs.This Heavy-Duty Industrial Profile Sander is designed for High-Speed Sanding/Denibbing of Profiles, Mouldings, and Trim, and is currently hooked up and fully operational (not sitting in a warehouse gathering dust). Buyers are welcome to schedule an Inspection and see it under power before your purchase.

Makor Start One M (S-ONE-M) Finishing Line Infeed & Outfeed System Storage Trolleys This line has been removed from operation and is in dry storage, as shown in the last (3) photos.

2003 Makor UV Oven MORE INFORMATION COMING SOON!

System includes: Vacuum Coater UV Oven with (9) lamps Lateral Transfer Table Max width 9" Able to run clear or pigmented coating

Two Bay 52" capacity Pneumatic clamping

2005 Marathon Spray Booth 14' wide x 25.5' long x 8'9" tall Booth only no racks, spray guns, paint pots etc included

MARINUS - Promax: End Matcher with Defecting, Cut to Length, & Optimizing Cutoff CapabilitiesFeatures & Specifications -- Heavy and stable construction. -- Cutterhead carriage and Clamp System utilizes: HD Lineal bearings; grease lubricated. -- Heavy-Duty, low maintenance Feed Chains into machine: Takeaway of material after cutting/end matching. -- Continuous high-speed feeding system with: Accurate positioning utilizing HD Servo Drives. -- (2) Servo Motors for: Max. feed control and acceleration & deceleration control. -- Servo driven feed motor & gearbox for: Highest efficiency speed feeding & control of the cutterhead carriage. Includes: Independent stepless speed control forward & reverse. -- Pneumatic side pushers (holding material firmly against the fence) for: Guaranteed square angle cut. -- (2) Cutoff sawing Servo motors: 5 HP Each (3.0 kW) – 450 mm (17.7";) dia. blades with: Inverters (VDFs) for varying blade speed. -- (2) High-speed milling head Servo motors with Inverter (VFD): 12 HP - 7.5 kW Each; speeds to 12,000 RPM; 5"; (125 mm) dia. -- Adjustable cutterhead stroke based on material width to increase throughput speed based on the width of material input. -- (1) Luminescence sensor camera for defect crayon mark. -- Inductive Sensors: For detecting the position of the carriage and others for detecting the positions of the saw blades. -- Cutoff waste powered belt conveyor in machine (below feed system; 12"; from floor) with: Drive motor for waste cutoff pieces taken to the outfeed end of the machine. Other Technical Specification -- Machine with: Completely enclosed by safety doors; produced to CE Safety & Electrical Standards to UL/CSA Standards. -- LENZE PLC Control. -- Operation from Operator Control with: Touchscreen control; mounted on the front right cover of the machine. -- Air pressure required: 85 PSI (6 Bare). -- 1" x 8"; (200 mm) & 2 x 4-3/4"; (120 mm) Dia. dust outlets; approx. 5,000 - 5,500 mm and from 3,050 - 3,350 CFM. -- Router Remote Access with: Internet connection; factory can monitor the performance of your machine. - Also allows for easy access to service, softwareupdates, & downloads.Input & Output Material Specifications -- Board widths: 2"; (50 mm) Min. to 12.28"; (312 mm) max.; min. width: 1-3/4"; (44.5 mm) min. -- Board input lengths: 17.9"; (450 mm) min. to 20 ft. (6,000 mm) max. -- Board output lengths: 15-3/4"; (400 mm) min. -- An available short piece option can be added to reduce output; length to 10"; (250 mm) min. -- Board widths: 2"; (50 mm) Min. to 12" (300 mm) max. -- Board input lengths: 17.9"; (450 mm) Min. to 20 ft. (6,000 mm) max. -- Board thickness: Min. to 0.315"; (8 mm) on request to 1 1/3"; (32 mm).Standard Programs / Programming -- Machine is equipped with: (2) Primary Programs. 1. End matching: Trimming ends and end matching. 2. Cutting only (no end matching). -- (3) Subprograms 1. Defecting cutting & end matching: Operator marks defects with a crayon; machines cut out

MARTIN - SHM-08622: Shaper -- Specifications7.5 HP - 3,450 RPM Motor.1-1/4" Dia. spindle.8" Max. cap. under nut. -- 42" x 37" Solid cast iron precision ground Table; ribbed construction. -- NOTE: Machine runs great; however, we do not have the micro adjustment fence.

--In auction: https://exfactoryauctions.com/Detail/SH-230492/event/A122024$1 --NO RESERVE!-- MARTIN T 23 Tilting Spindle Shaper, with 30 mm (1.18") Interchangeable Spindle & Power Feeder Specifications: Table size 940 x 1100 x 850 mm (37.01” x 43.31” x 33.46”) H, with Table insert dia. 90, 130, 205, 305, & 480 (3.54”, 5.12", 8.07”, 12.01”, & 18.90”). Spindle tilt 0° to 45°. Maximum capacity under nut 7". Vertical spindle adjustment 145 mm (5.71"). Spindle speeds 3000, 4,500, 6,000, & 90,000 RPM. Equipped with: 6.4/7.8 HP Motor. "MK5" Spindle shaft. Mechanical spindle brake, with Foot pedal. Hand spindle lock. Complete with: 11-1/2” x 4-3/4” Left & Right Fences, with 21” x 6” H Left & Right Wood fences. 1996 CO-MATIC 1 HP 4-Speed 4-Roll Power Feeder, with Speeds 13, 26, 26, & 72 FPM. Dimensions with Power Feeder: 42" x 42" x 63” H.

MARTIN T71 10' Sliding Table SawSpecifications: -- 10' Cutting cap.; 9-1/2' sliding table, 3-position table locking mechanism; cast iron machine table; 7.5 HP motor; tilting saw arbor (arbor speed 2,800 - 4,000 & 5,500 RPM) with tilting from 0° - 45.5°, 450 mm (17.72") saw blade cap.; 1 HP - 9,400 RPM scoring motor. -- Max. cutting height: 5-11/16"; Hydraulic saw blade height & tilt adjustment by foot pedal control; cutting width between saw blade & rip fence: 49". -- Complete with: -- Rip fence with micro-adjust; crosscut fence flip stops.

MARUNAKA - SL-250V: Inline SlicerSpecifications9.8" Max. slicing width at a 75° knife angle; maxi. veneer thickness: 1/10"; knife bias angle: 75° to 85°; upper feed beam continuous belt feed; (2) feed speeds: 141 or 198 FPM; 15 HP feed motor.Complete with: Motorized upper feed beam that adjusts automatically during slicing at Cant changes; fine handwheel adjustment of front bed longitudinally or vertically; knife size: 47.2" long x 7.3" wide x 0.80" thick.Machine comes with: (3) Knives.NOTE: No merry-go-round included.

MARUNAKA Model RD – 8J WIDE Single Deck Veneer Roll Dryer;Complete with the following features: -- 1988 - year of manufacture. --Working width – 51"; --Length of the dryer – 24 Ft (4 Sections) --Type of heating - Steam --Operational in 2018 when mill closed --Professional rigging and loading available.

MARUNAKA Model RD-3UB/RD-6UB (Connected) Single Deck Veneer Roll Dryer;Complete with the following features: -- (3) 3 HP circulating fans with (1) 3 HP exhaust blower thru the ceiling. -- Optional heat source: electric (7) Elements/Zones, computer controlled thermocouples in addition to (2) Natural gas burners (OEM).. Both dryers have a 100amp circuit breaker with 100amp fuses. The RD 8 operates with 4 fan motors and 4 heaters. The RD 6 has 3 fan motors and 3 heaters";.. -- Capable of temperatures to 120° Celsius (250° Fahrenheit). -- Working width 1000 mm or about 39 inches. Veneer is fed endo.Please Note: -- Dryer is (2) separate units; all equipment will fit into a 40' container for shipment from Eastern USA. -- All equipment is in good working condition including all fans and blower, temperature control works properly; feed roll drive works well. -- Rolls have been nickel treated to minimize corrosion/oxidation. -- This dryer equipment is still in place. -- MARUNAKA (2) Models: RD-3UB and RD-6UB currently connected to increase capacity. Can easily be separated.NOTE: Refurbished in 2005, operated from 2005 - 2012. Still operational ready to work!

MASTER MACHINERY - MC-MDS-1: Single Spindle ShaperSpecifications -- Table size: 27-1/2" x 32". -- Spindle speed: 7,500 - 10,000 RPM. -- Main motor: 3 HP.

MASTERWOOD PROJECT 313 CNC MACHINING CENTER (W/ACT/BORING): -- Specifications:Working Capacity:"X" Axis 3,080 mm (121"), "Y" axis 1,100 mm (43") width; -- Positioning Speed:Programming speed in X-axis 197 FPM (60 MPM), Y-axis 162 FPM (49 MPM), Z-axis 58 FPM (18 MPM). -- Boring unit:(13) independent vertical spindles, (9) in X-axis, (5) in Y-axis; (4) horizontal spindles with (1 + 1) in X-axis for edge boring in the left- & right-hand panel edges. -- Machining:(1) 7.5 HP (5.6 kW) high speed router (1,000 - 24,000 RPM) by frequency inverter; 1.5 HP (1.1 kW), 6,000 RPM grooving saw with manual rotation for X-axis or Y-axis; -- Work Table: (6) moveable support rails with (2) vacuum cups ea., double zero settings, (6) pneumatic backstops and (2) pneumatic side stops creating (2) working zones. -- Operator & Machine Control:TECNOSUD "K68800" Microprocessor control for (3) axis, lineal, circular, and helical interpolation. Equipped with 14" color video graphic monitor, keyboard for data entry, 1.44 MB floppy disk drive, 64K RAM, RS-232 for possible connection to office PC, all mounted in separate free-standing control cabinet; features to run CPL/Parametric "TRIG" programming and "Spline" CAD/CAM. -- Complete with: Dual zone vacuum pump. Ontario Hydro approved electrics. -- Actual Model is MASTERWOOD PROJECT 313

MASTERWOOD PROJECT 317 CNC MACHINING CENTER (P.T.P): Specifications -- Working Capacity: "X" Axis: 102" (2,600 mm); "Y" Axis: 37-1/2" (950 mm); "Z" Axis stroke: 5.9" (150 mm); max. material thickness: 2.36" (60 mm). -- Positioning Speed: "X" Axis: 164 FPM (50 MPM); "Y" Axis: 131 FPM (40 MPM); "Z" Axis: 25 FPM (8 MPM). -- Work Area: (6) Adjustable panel supports; ea. with: (2) Vacuum pods; (4) panel lifting blades for heavy parts; (6) fixed pop up rear stops; (1) side R/H stop; (1) L/H stop.Machine bed is divided into: (2) Independent working zones with mirror image capability. -- Boring Unit:.2 HP (1.5 kW) - 4,000 RPM Motor; (10) independent vertical boring spindles with: (7) Spindles in "X"-axis & (3) spindles in "Y"-axis. (6) Horizontal spindles with: (2 + 2) In "X"-axis; (1 + 1) in "Y"-axis; (1) 12,000 RPM "X"-axis grooving saw with: 125 mm Dia. blade. -- Machining: (1) 9 HP (6.7 kW) Vertically mounted electrospindle router with: ISO 30 Adaptor & ceramic bearings; variable speed: 6,000 - 24,000 RPM.(1) 4-Position automatic tool changer mounted to the machine head for "on the fly" ATC. -- Operator & Machine Control: PC Front-end controller; MASTERWOOD "MW 310" CNC + Windows Operating System; multitask software with: Graphic interactive editing & boring optimization program.Features -- 14" VGA Color monitor; MHZ processor; 64 MB SDRAM; 6.4 GB hard drive; 56 K modem, 1.44 MB floppy & CD ROM drives; Ethernet card; serial port; mouse; RS-232 port for remote programming from an office PC is possible -- Software includes: Realization of profiles & parametric drawings; graphic basic macros for simple & complex elaboration; graphic visualization of the surfaces to be machined; IN/OUT diagnostic; programming for drilling & routing operations with machine settings & tool editor.Includes -- Vacuum Pump.NOTE: Description based on Model Type, manufacturer's plate, and information from Seller; please inspect to confirm the required specifications. Dimensions & Weight data are based on: 3rd Party information and could be incorrect; please verify & confirm if accurate dimensions & weight are required.

MASTERWOOD - Project 450L: CNC Machining CenterSpecifications -- X-Y-Z Axis strokes: 5,820 - 1,900 - 350 mm.Axis speed X-Y-Z: 80 - 80 - 25 MP.Aluminum panel support blocks: 8.Middle reference stops: 8.Front reference stops: 9.Side reference stops: 2 dx - 2 sx.Panel carrying knives: 4. -- Distance between drills: 32 mm.Engine power: 1.7 kW.Drill rotation speed: 4,000 RPM.12 kW Air-cooled motor with: HSK 63 Tool holder. -- Numerical Control with: P; max. power: 37.3 kVA.Amps: 53.8.Working Pressure: 7 - 8 bar.Compressed air consumption: ~ 100 Nl/Min. -- Upper dust extraction outlet: Ø 250 mm. Dust extraction outlet for sawdust coming out of the conveyor belt: Ø 120 mm; dust extractor air output speed: 25 - 30 m/Sec; dust extractor air consumption: 4,900 cbm/Hr.Includes -- Vacuum Pump; (12) extra ISO collets; aggregate HSD.Note: Description based on Model Type, manufacturer's plate, and information from Seller. Please inspect to confirm the required specifications. Dimensions & Weight data are based on 3rd party information and could be incorrect; please verify & confirm if accurate dimensions & weight are required.