Woodworking Equipment For Sale

Schultz Tool Veneer Bladder Membrane Press Seller’s Soecification: - Veneer Membrane Press - Approx. 55?x106? press capacity - Hot air design w/ 3mm silicone membrane - Specification – - Typical cycle time of 3 min. using proper glue that sets at 200° F - Can use PVA, but extends cycle time to approx. 15-45 min. depending on glue mix to achieve 80%+ cure strength - All mechanical components operational - Needs 4 to 5 heating rods replaced. - We have replacements but do not have the ability to replace them - Current operational temperature is 150°

1998 SCM TECH 30 Super Router

2008 SCM Morbidelli Universal 3612

Tubeless Vaccum (TNV) Electro-Spindle with HSK63F quick release Toolholder Rotation speed 600-2400 rpm Air Cooling by rear electrofan Static Inverter Centralized dust collection system with automatic blast gates

Worktable dimensions: 145? x 61? Z -Axis stroke: 9.84? Spindle speed: 24,000 RPM Electrospindle (S1/S6 rating): 7.5 HP / 9HP Tool Changer: 10 position Spindle Taper: HSK 63 Boring Block (7) Spindles: 6,000 RPM Maximum positioning vectorial speeds: X/Y axis: 115 feet/minute Electrics: 208/230/460 volts, 3-phase, 60 cycles EQUIPPED WITH: Windows Based Operating system 17” Flat Panel Monitor Remote Pendant with 7? Display 7-Spindle Boring Block Touch Probe Spindle Air Blowers Built In Vacuum Pumps- 2 Zones

SCM - Concept 2000, ...Double End Tenoner.Double End Tenoner with: Jump scoring, Hogging, Shaping with stacked tooling. -- 122" Opening cap., motorized opening with keypad entry & LED readout, 12" infeed chain area in front of holddowns. -- 0" - 4" Motorized thickness opening with mechanical digital readout. -- 6" Min. width, 2-post machine. Each side equipped with: -- 1st Station: Jump scoring. -- 2nd Station: Hogging unit. -- 3rd Station: Coping head with stacked tooling capacity (manually operated). -- 4.5 HP Drive for 10 - 60 FPM variable feed speed. -- Chain dogs on 15-3/4" centers, rubber top nonmarring chain pads. -- Heavy-Duty chain links with: Needle bearings, automatic oil mist chain oiler, automatic brake on feed motor with emergency stop.Complete with: -- Upper driven holddowns with: Continuous feed belts; feed beams can be disengaged for conventional part feeding in front of dogs. -- Mobile remote control for setup; dual lead screw for traversing beam; exhaust hoods on all heads.Note: Tear down and loading not included.

SCM PRATIX S-15-B FLAT TABLE MACHINE (W/ATC/BORING): -- Specifications:Single 5' x 12' traveling "Bridge Gantry" and stationary aluminum dual vacuum table with a MATRIX square grid pattern for fixturing parts.Grid pattern allows use of vacuum pods or closed cell rope gasketing material and use of spoil boards for "nested base machining".(8) Part location pop-up pins mounted on the table perimeter. -- Working field:"X" Axis is 145.11" (3,686 mm); "Y" axis is 61.2" (1,555 mm); "Z" axis stroke is 9.8" (250 mm); max. material thickness 4" (100 mm). -- Positioning Speed:"X" & "Y" Axis 115 FPM (35 MPM); "Z" axis at 82 FPM (26 MPM); closed loop AC Servo drive system.High precision "Rack & Pinion" system in "X" & "Y" axis & ground ball screws "Z" axis; all axes ride on extra large precision profile linear guideways. -- Boring Unit:3 HP (2.2 kW) - 6,000 RPM motor; (7) vertical spindles on 32 mm centers, (5) in "X" axis & (2) in "Y" axis. -- Machining:(1) 9 HP (6.7 kW) Air-cooled electro spindle with HSK F63 adaptor; variable spindle speeds from 1,500 - 24,000 RPM.(1) 14-Position ATC tool rack mounted to the machine base. -- Operator & Machine Control:PC Front End with: "XILOG Plus" + Windows "XP Pro" Operating System; 17" high resolution LCD; ergonomic keypad.USB Ports, serial ports RS-232 & RS-242 & Ethernet adaptor; programs can be transferred via disk or downloading by wire is possible.All computer components are mounted on a mobile stand.XILOG Plus Offers: Incredible list of functions from: (a) Auto-diagnostic to (z) zooming; controlled acceleration & deceleration, encoder feedback, dynamic tool correction via PLC due to active tool wear using space-and-time criteria. -- Additionally equipped with:Onboard mini-CAD with built-in programming for writing circles, ellipses & angles with only a few keystrokes; Onboard cycle optimization, onboard calculator, mirror-imaging, and repeat imaging. -- Complete with:(1) 300 m³/Hr Vacuum Pump; external transformer 208/230/480 Volt; safety enclosure around the spindle carriage; tool length probe sensor; manual centralized lubrication.Includes: (1) Universal Remote Pendant, 7" color display allows for the effective management of all machine functions from manual Jog Mode to loading & execution of a program.The pendant is fitted with a USB port to allow quick load & setup of new programs; safety "bump-stop" bumpers; emergency stop rope & manuals. -- Actual Model is SCM - PRATIX S-15-B.

SCM - PRATIX S-15-C: Flat Table Machine (w/ATC/Boring) + Rake -- SpecificationsSingle 5' x 12' traveling "Bridge Gantry"; stationary aluminum dual vacuum table with: MATRIX Square grid pattern for fixturing parts.Grid pattern allows use of: Vacuum pods or closed cell rope gasketing material; use of spoil boards for "nested base machining".(8) Part location pop-up pins mounted on the table perimeter. -- Working Field"X" Axis: 145.11" (3,686 mm); "Y" axis: 61.2" (1,555 mm); "Z" axis stroke: 9.8" (250 mm); max. material thickness: 4" (100 mm). -- Positioning Speed"X" & "Y" Axis: 115 FPM (35 MPM); "Z" axis: 82 FPM (26 MPM); closed loop AC Servo drive system.High precision "Rack & Pinion" system in "X" & "Y" axis; ground ball screws "Z" axis; all axes ride on extra-large precision profile linear guideways. -- Boring Unit 3 HP (2.2 kW) - 6,000 RPM motor; (12) vertical spindles on 32 mm centers: (7) In "X" axis & (5) in "Y" axis. -- Machining(1) 11 HP (8.2 kW) Air-cooled electrospindle with: HSK F63 Adaptor; variable spindle speeds from: 1,500 - 24,000 RPM.(1) 14-Position ATC tool rack mounted to the machine base. -- Operator & Machine ControlPC Front-End with: "XILOG Plus" + Windows "XP Pro" Operating System; 17" high resolution LCD; ergonomic keypad.USB Ports; serial ports RS-232 & RS-242; Ethernet adaptor; programs can be transferred via disk or downloading by wire is possible.All computer components are mounted on a mobile stand.XILOG Plus Offers: Incredible list of functions from: (a) Auto-diagnostic to (z) zooming; controlled acceleration & deceleration; encoder feedback; dynamic tool correction via PLC due to active tool wear using space-and-time criteria. -- Additionally equipped with:Onboard mini-CAD with built-in programming for writing: Circles, ellipses & angles with only a few keystrokes; onboard cycle optimization; onboard calculator; mirror imaging; and repeat imaging. -- Complete with:(2) 6.4 KW/8.5 HP Vacuum Pumps; external transformer 208/230/480 Volt; safety enclosure around the spindle carriage; tool length probe sensor; manual centralized lubrication.Includes: (1) Universal Remote Pendant; 7" color display: Allows for the effective management of all machine functions from manual Jog Mode to Loading & Execution of a program.Pendant is fitted with: USB Port to allow quick load & setup of new programs; safety "bump stop" bumpers; emergency stop rope & manuals. -- Options IncludeAdditional items pictured are included with this machine. -- Actual Model: SCM - PRATIX S-15-C

SCM - ACTION TF 2500: Case Clamp (Automatic Feed Through) -- Specifications Max. standard working dimensions: 2,500 mm (98.4") Wide x 1,250 mm (49.2") high x 800 mm (31.5") depth. -- Min. standard working dimensions: 250 mm (9.8" Wide x 250 mm (9.8") high x 250 mm (9.8") depth. -- Working table height: 600 mm (23.6"). -- Max. Vertical pressing force: 1,500 kG (3,300 Lbs). Max. Side pressing force: 1,200 kG (2,640 Lbs).Features -- Full top & bottom platen for maximizing pressing PSI on the box. -- Rack & Pinion guides at: All (4) corners of the top platen & side pressure to keep the top platen parallel and the side pressure square. -- Sizes of box can be input for efficient cycle control when running repetitive box closings. -- Machine can also find the size of the box, so all the Operator does is place the box onto the powered infeed belt to be clamped. -- The vertical & horizontal pressure is adjustable according to the type of furniture to be assembled. -- Machine is equipped with: (3) Side pressure bars & able to sequence different furniture pieces without manual intervention. -- Pressure supplied by infinitely adjustable brushless electric motors.Complete with: -- 5.7" Touchscreen panel with: Software by CPC to program cycles. -- Rack & Pinion system; Brushless motors. -- Front & rear photocell barriers. -- Actual Model SCM ACTION TF 2500

SCM - ACTION FL 2500: Case Camp (Semi-Automatic) -- SpecificationsMax. standard working dimensions: 2,500 mm (98.4") Wide x 1,250 mm (49.2") high x 800 mm (31-1/2") depth. -- Min. standard working dimensions: 250 mm (9.8" Wide x 250 mm (9.8") high x 150 mm (5.9") depth. -- Working height: 508 mm (20"). -- Vertical pressing force: 15 kN (3,372 Lbs).Features -- Full top & bottom platen for: Maximizing pressing PSI on the box. -- Rack & Pinion guides: All (4) corners of the top platen & side pressure to keep the top platen parallel and the side pressure square. -- Sizes of box can be input for efficient cycle control when running repetitive box closings. -- Machine finds the size of the box; Operator only opens the Clamp to a size larger than the box to be clamped. -- Vertical & horizontal pressure: Adjustable according to the type of furniture to be assembled. -- Machine is equipped with: (3) Side pressure bars & able to sequence different furniture pieces without manual intervention. -- Pressure supplied by: Infinitely adjustable brushless electric motors.Complete with: -- 5.7" Touchscreen panel with: CPC Software to program cycles. -- Rack & Pinion system, brushless motors. -- Front & rear photocell barriers. -- Actual Model SCM CPC ACTION FL 2500

SCM - ACTION FL 2500: Case Clamp (Semiautomatic)Specifications -- Max. standard working dimensions: 2,500 mm (98.4") Wide x 1,250 mm (49.2") high x 800 mm (31-1/2") depth. -- Min. standard working dimensions: 250 mm (9.8") Wide x 250 mm (9.8") high x 150 mm (5.9") depth. -- Working height: 508 mm (20"). -- Vertical pressing force: 15 KN (3,372 Lbs.).Features -- Full top & bottom platen for maximizing pressing PSI on the box. -- Rack & Pinion guides: At all (4) corners of the top platen & side pressure to keep the top platen parallel and the side pressure square. -- Sizes of box can be input for efficient cycle control when running repetitive box closings. -- The machine can also find the size of the box, so all the Operator has to do is open the Clamp to a size larger than the box to be clamped. -- The vertical & horizontal pressure: Adjustable according to the type of furniture to be assembled. -- The machine is equipped with: (3) Side pressure bars & able to sequence different furniture pieces without manual intervention. -- Pressure supplied by: Infinitely adjustable brushless electromotors.Complete with: -- 5.7" Touchscreen panel with: Software by CPC in order to program cycles. -- Rack & Pinion system; brushless motors. -- Front & rear photocell barriers. -- Actual Model: SCM - CPC ACTION FL 2500

2019 SCM Stefani KDR with return conveyor.

SCM - OLIMPIC K230R EVO: Edgebander (w/Premilling) -- Specifications0.4mm to 3mm Edge thickness; panel thickness 8 mm to 50 mm (0.3" to 1.96"); minimum part width 60mm (2.36"); minimum part length 160 mm (6.30").Minimum distance between panels: 559 mm (22";); 29-1/2 FPM (98 MPM) Fixed feed speed; 1.0 HP (0.75 kW) feed drive.Premilling Station(2) 2.0 HP (1.5 kW) Motors to rectify/clean panels already sized. -- Adjustable infeed fence: Manually preset with digital indicator, pneumatic in/out positioning.Equipped with: 1.5 kG TEFLON Coated glue pot; glue roller application system complete with: Automatic recycling device for unused glue.Digital thermostat adjustment for temperature control; pneumatic guillotine; heating time approx. (8 - 10) Min.3-Roll pressure unit with: Pneumatic controls for all pressure rollers. -- Automatic strip & coil feed magazine.Workstations2-Motor front & rear End Trimming (1/2 HP - 12,000 RPM ea. motor.); tilts 0° - 15°; end trimmers mounted on THK guide. -- Top & bottom flush & bevel trims with: Quick release mount and plug-in motors for quick tooling changes.0.5 HP - 12.000 RPM Motor ea.; bevels 0° - 15° with: Precision digital indicators for quick setup. -- Top & bottom scraping unit with: Manual positioning. -- Top & bottom buffing unit (1/4 HP - 3,000 RPM motors); tilts up to 12°. Operator & Machine Control"ORION 1 Plus" Controller: Located at the infeed of the machine; capable of operating all the work units via soft touch buttons.It pneumatically tilts the end trim unit from the Control Panel; eliminates the use of micro switches, as well as controls the temperature of the glue.Control is tilted slightly upward for a more ergonomically friendly position for the Operator. -- Actual Model is: SCM OLIMPIC K230R EVO

SCM SANDYA - 40 M3 135, ...3-Head Wide Belt Sander 52" Width cap. Drum, Drum, Combination HeadHead Configuration:1st Head: Steel Contact 22 kW Pneumatic blowdown and alignment.2nd Head : Rubber Contact 18.5 kW Pneumatic blowdown and alignment.3rd Head: Combination Platen 15 kW Pneumatic blowdown and alignment.Note:The SCM sander does not have a brush. After the 3rd head, it has this pneumatic blow-off bar with multiple blow-offs running the length of the sanders width. Sander can be seen under power if needed.Specifications: -- 53" x 103" Abrasive belts with electronic tracking. -- All heads with abrasive belt grit compensation. -- Conveyor belt feed with dual feed speed, 5 HP motor. -- Automatic part thickness adjustment. -- Motorized thickness opening via (4) precision conveyor bed jacks with LED readout. --0" - 7-7/8" opening. -- Equipped with & Features -- Outfeed rubber covered holddown rolls or shoes on all heads. -- Motor load meters. --Infeed and outfeed conveyor extensions. -- WYE-DELTA soft start.Note: The SANDYA model "40" is more or less the same as the SANDYA "30" but more Heavy Duty.

SCM OLIMPIC K360 ERT HP: Compact Edgebander (w/Premill & Corner Rounding)Specifications -- Edge Capacity: 0.4 - 6 mm (0.016 to 1/4") For strip feeding. -- Panel Capacity: Min. width 65 mm & 140 mm min. length (2-3/8" & 5-1/2"); panel thickness: Min./max. 8 - 60 mm (3/8" - 2-1/2").Equipped with: -- Adjustable Infeed Fence: Manually preset with digital indicator, pneumatic in/out positioning. -- Premilling Station RT-VP: Spindles (2) x 2.0 HP - 19,000 RPM; (1) with PLC controlled jump action & diamond cutterheads. -- Automatic Strip & Coil Feed Magazine: For straight edges & 3 mm guillotine for coils. -- Gluing Station for EVA (Hot Melt) with: Teflon coated glue tank & quick disconnect to change glue tanks fast if needed; heat up time: Approx. (10) Min. -- Pressure Section: Manual digital positioning; (3) pressure rollers: First larger; Teflon coated & powered. Workstations -- End Trimming Station. Front & rear: (2) x 1/4 HP - 12,000 RPM motors; mounted on THK guides; swivels 0° - 15°; rapid setup between straight & angled cutting with: Automatic swivel cylinder. -- Trimming Unit Flush/Bevel/Radius: Top/Bottom remote (via control panel) pneumatic positioning for (3) settings; Flush/bevel/radius trimming; (2) x 0.7 HP - 12.000 RPM motors with: Precision digital indicators for quick setup. -- Corner Rounding Unit "Round 2M" with: (2) 0.8 HP Independent motors that slide on THK guides. -- Profile Scraping Unit "RAS/V": Top/Bottom, manual preset up with digital indicators; large dia. copy wheels for max. accuracy & pneumatic in/out positioning. -- Buffing Unit: Top/bottom; (2) x 1/4 HP - 2,800 RPM motors; tilting up to 12°. Operator Interface -- ORION "1 Plus" Controller. Fixed at infeed of machine with: "Touch Screen" control with soft keys, graphics, & LCD display panel; handles most machine setup functions & workstations. Complete with & Features -- Feed speed: 36 FPM Fixed; (1) x 2.0 HP feed drive motor; 200 Hz frequency inverter for all trimming units. -- Manual adjustable hold-down pressure beam; full sound enclosure cover; outboard panel support. -- Actual Model: SCM OLIMPIC K360 ERT HP

SCM - OLIMPIC K 600 T-ERL: Edgebander with Premill & Corner RoundingSpecifications -- Edge Capacity: 0.4 to 8 mm (0.016 to 0.31") for strip feeding. -- Panel Capacity Min. panel width: 52 mm (2"); Min Panel length: 140 mm (5-1/2").Min./Max. panel thickness: 8 - 60 mm (0.36" - 2.4"); Min. distance between panels: 600 mm (24").Equipped with: -- Adjustable Infeed Fence. Manually preset with: Digital indicator; pneumatic in/out positioning. -- Premilling Station "RT-E": 2 x 3.0 HP Spindles; 12,000 RPM motor each. -- Automatic Strip & Coil Feed Magazine. For straight edges; 3 mm guillotine for coils. -- Gluing Station "VC/6". EVA (Hot Melt) with: Quick change/disconnect TEFLON glue pot for fast glue tanks change, if needed. Heat-up time: 8 - 10 Min. (approx.) -- Pressure Section: Manual digital positioning; TEFLON coated pneumatic driven roller; (2) spring loaded idle rollers.WORKSTATIONS -- End Trimming Station "K-SEL 2". Front & rear: (2) x 1/2 HP - 12,000 RPM motors; mounted on THK guides; swivels 0° - 15°; rapid set up between straight & angled cutting with: Automatic swivel cylinder. -- Top & Bottom Trimming Unit "RI/100" with: (2) x 1.0 HP - 12.000 RPM motors; capable of tilting from: 0° - 25° with adjustment & pneumatic positioning for (3) settings; flush/bevel/radius trimming for quick setup. -- Corner Rounding Unit "Round-K" unit with: (2) 0.80 HP Independent motors that slide on THK guides -- Top & Bottom Profile Scraping Unit "RAS/K". Unit with: Digital indicators; large dia. copy wheels for max. accuracy; pneumatic in/out positioning. -- Buffing Unit. Top/bottom: (2) x 1/4 HP - 2,800 RPM motors; tilting up to 12°.Operator Interface -- "STARTOUCH" Controller with: 12" Touchscreen display; capable of storing (100) programs. Machine automation by: PLC Function; encoder positioned in the panel feed track pinion.Diagnostics for a quick solution to errors.Process statistics data, i.e.: Number of pieces/edges and track feeding.Features & Complete with: -- 2-Speed feed speed of: 36 & 52 FPM (11 & 16 MPM); 1 x 2-1/2 HP feed drive motor; max. speed when using CR unit is: 36 FPM (11 MPM). -- 200 Hz Frequency Inverter: All trimming units. -- Manual adjustable holddown pressure beam. -- Full sound enclosure cover & outboard panel support. -- Actual Model - SCM OLIMPIC K 600 T-ERL

SCM SANDYA 10/S M2 2-Head Wide Belt SanderHead Configuration1st Head: 7" Diameter Spirally-grooved steel contact roll, 20 HP Motor.2nd Head: Combination head, 7" Diameter Spirally-grooved rubber-coated contact roll, Finishing platen with Electronic sectional pad with EPICS System, 3-1/2" Steel contact roll, 13 kW (17-1/2 HP) Motor.Specifications: -- 4.5 - 9 m/min (15 - 30 FPM) Variable feed speeds, -- Part thickness 4 mm (0.2") to 170 mm (6.7"). -- 43" W x 103" L Abrasive belt, Electronic sanding belt tracking & Pneumatic belt tensioning. -- 34" H Natural rubber feed belt,Equipped with & Features -- Automatic thickness adjustment, Automatic feed belt tracking & Tensioning, -- Motorized rise & fall of working table, -- Part thickness & Conveyor belt speed LED readout, -- Infeed safety bar for operator protection and oversized parts. -- 3" Diameter Entry & exit rolls, 13" L 2-Roll Infeed & Outfeed extensions with 2" Diameter Rollers & Manifold. -- Unopened box of (10) KP520 100 Grit Belts (Purchased for $500).Dimensions: 88" L x 86" W x 90" H.Weight: 4,440 Lbs.

SCM SANDYA 7 RCS Wide Belt Sander2-Head, 42" cap. - Great solid wood finish Sander. -- 1st Head: Grooved steel contact roll, 6-1/4" dia., 30 HP motor -- 2nd Head: Combination head, rubber covered contact roll, 6-1/4" dia. (65 Shore), and 2" wide finishing platen, 25 HP motor. -- 43" x 75" or 85" Abrasive belts with electronic tracking & pneumatic belt tensioning, pneumatic exclusion of all contact rolls. -- Conveyor belt feed with variable feed speed, 14.5 - 30 FPM, 1.5 HP motor, automatic part thickness adjustment, -- Motorized thickness opening with LED readout,0" - 6-1/4" via (4) precision conveyor bed jacks. -- Infeed & outfeed spring loaded rubber covered holddown rolls on all heads, -- Motor load meters, infeed and outfeed conveyor extensions, WYE-DELTA soft start.

SCMI - OLIMPIC K 360: Compact Edgebander with PremillingSpecifications -- Edge Capacity: 0.3 - 3 mm (0.012 to 0.118") For coiled edges (0.3 - 6 mm for strips with 6 x 60 mm kit included). - Coil holder-plate dia.: 780 mm (31"). -- Panel Capacity: Min. width: 90 mm & 140 mm Min. length (3-1/2" and 5-1/2").Panel thickness. Min./max.: 8 - 50 mm (3/8" - 2") to max. 60 mm (2.4" with 6 x 60 kit included).Equipped with: -- Adjustable Infeed Fence. Manually preset with: Digital indicator; pneumatic in/out positioning. -- Premilling Station: RT-VP. Spindles 2 x 2.0 HP - 19,000 RPM; (1) with; PLC Controlled jump action & diamond cutterheads. -- Automatic Strip & Coil Feed Magazine. For straight edges & 3 mm guillotine for coils. -- Gluing Station. For EVA (Hot Melt) with: TEFLON Coated glue tank; quick disconnect to change glue tanks fast if needed; heat up time approx. 10 Min; includes: 1.5 kG Glue pot instead of standard. -- Pressure Section. Manual digital positioning: (3) Pressure rollers; 1st larger TEFLON coated & powered. Workstations -- End Trimming Station - K2: Front & rear 2 x 1/2 HP (included extra); 2,000 RPM motors mounted on: THK guides; swivels 0° - 15°; rapid setup between: Straight & angled cutting with the automatic swivel cylinder.Automatic positioning for: (3) Cutting modes: Straight, chamfered, and radiusing of thick edges. -- Top & Bottom Trimming Unit: R-K. Remote (via control panel) pneumatic positioning for: (3) Settings: Flush/bevel/radius trimming; (2) x 0.7 HP - 12,000 RPM motors with: Precision digital indicators for quick setup. -- Top & Bottom Profile Scraping Unit: Manual preset up with: Digital indicators; large dia. copy wheels for: Max. accuracy & pneumatic in/out positioning. -- Buffing Unit - SP-V. Top/bottom; (2) x 1/4 HP - 2,800 RPM motors; tilting up to 12°; cleaning & polishing of edges.Controls -- Orion 1 Plus Controller. Fixed at infeed of machine with: Soft keys; graphics; 4" LCD display panel. Handles most machine setup functions & workstations. Machine automation by: PLC Function & encoder positioned in the panel feed track pinion. Diagnostics for: Quick solution to many errors. Process statistics data, i.e.: No. of pieces/edges and track feeding.Features & Complete with: -- Feedspeed: 36 FPM Fixed; (1) x 2.0 HP feed drive motor; 200 Hz frequency inverter for all trimming units; manual adjustable holddown pressure beam; full sound enclosure cover & outboard panel support. -- Overall dimensions:3,600 mm (142") x 900 mm (36") x 1,600 mm (63"); weight approx.: 997 kG (2,200 Lbs). -- Owner states: Several motors/groups replaced recently as routine maintenance. -- UL/CSA Approved version; has "Ontario Hydro Special Inspection" approval sticker. --Actual Model: OLIMPIC K 360 T-ER1

SCM - OLIMPIC K 201 HFA, ...Automatic Compact Edgebander with: 3 mm Max. coiled edgebanding thickness & High Frequency motorsSpecifications: -- Edgebanding thickness cap. (for both coil & strip): 0.4 - 3 mm (0.02" - 0.19"). -- Min. panel length for coiled edges (min. width 200 mm) 140 mm (5.51"). -- Min. panel width for coiled edges: 65 mm (2.56"). -- Panel thickness: 8 - 40 mm (0.31" - 1.57"). -- Feed speed:9 MPM (29 FPM).Equipped with: -- Automatic adjustment of all units when panel thickness is changed. -- 20" Dia. coil table. -- Automatic coil feed magazine; manual strip feed. -- Teflon-coated glue pot. -- 1.2 mm (0.05") Cap. guillotine. -- Eye-level control with: GEFRAN "1000" LED Temperature controller. -- Adjustable feet.Workstations: -- Single-motor end trimming unit with: (1) 0.19 kW (1/4 HP) - 12,000 RPM High-frequency motor & copying device. -- Top & bottom flush trimming unit with: (2) 0.35 kW (1/2 HP) - 12,000 RPM high-frequency motors, and front & vertical copying devices.