Woodworking Equipment For Sale

TIMESAVER - TB-440-4, ...2-Head Wide Belt Sander40" Width cap.; Drum and Combination Head.Head Configuration:1st Head - 50 HP; 12" rubber covered contact head.2nd Head - 40 HP; combination platen head.Specifications: -- Sander completely rebuilt (15) years ago. -- Rubber covered abrasive rolls were recovered, grooved and balanced, along with ALL pinch rolls recovered at FLETCHER MACHINE CO., Lexington, NC. -- Electric eyes upgraded to BANNER's send and receive type; includes battery backup system for controls (no crashes when machine has power outage). -- Feed speed gear box driven by AC Drive controlled 10 HP motor. -- Rebuild included: Table removed and platens ground flat; all bearings replaced, including pinch rolls and tracking cylinders; tension cylinders plasma sprayed, reground & new factory seal kits. -- Entire machine was disassembled, sand blasted and DUPONT "Zolatone" primed and painted. -- RAINBOW brand feed conveyor belt replaced in 2014. -- Many more upgrades, too many to list: Please contact for additional information. -- Machine is in good condition, running daily, and has had regular recommended service intervals; includes all factory manuals, blueprint drawings, parts list with numbers supplied, and when machine was new. -- Machine used in solid wood wide belt sanding. -- Includes Cloth aluminum Oxide Belts: 7 - 50 grit; 1 - 60 grit; 8 - 80 grit; 2- 120 grit; 8 -1 80 grit..

TIMESAVERS 237-4IC Four-Head Wide Belt Sander37" Width cap. Drum, Drum, Drum, PlatenHead Configuration:1st Head: Rubber covered contact roll, 9-1/2" dia., 30 HP motor;2nd Head: Rubber covered contact roll, 9-1/2 " dia., 25 HP Motor. 3rd Head: 9-1/2" Grooved Rubber Covered Contact Drum With A 20 HP Motor4th Head: Finishing platen, 2-1/2" wide, 20 HP motorSpecification -- 37" x 75" abrasive belts with Pneumatic tracking. -- Motorized part thickness adjustment, height, 0" - 6" opening. -- Automatic part thickness adjustment, -- Infeed & outfeed spring loaded holddown shoes, -- Variable feed speed from 15 - 45 FPM, 5 HP motor. -- Pneumatic feed beltEquipped with & Features: -- Motor load meters, -- Infeed emergency stop bar, -- Controls mounted on belt loading side, -- Automatic Trabon bearing lubrication system, -- Disc brakes on sanding head motors, -- 30" infeed load area.Note: Some spec's need to be verified

TIMESAVERS 252-4-IC, ... Wide Belt Sander, 4-Head.4-Head, 51" cap. - Great sander for solid wood and veneer panels equipped with (2) Contact rolls and (2) Air platens. Head Configuration1st Head: Rubber covered contact roll, 9-1/2" dia. 60 - 70 Durometer, 40 HP motor.2nd Head: Rubber covered contact roll, 9-1/2" dia. 50-60 Durometer, 30 HP Motor.3rd and 4th Head: Finishing platens, 2-1/2" wide "Veneer Saver" inflateable platens with adjustable timers for leading and trailing edges, 20 HP motor each head.Specifications: -- 38" Constant pass line height of Vacuum conveyor with suction fan and motor bed assembly for veneer and solid wood sanding. -- Adjustable air floating infeed and outfeed hold down shoes. -- 52" x 103" abrasive belts with "POSI-TRAK" electronic tracking.Equipped with & Features: -- Motorized part thickness adjustment with mechanical digital readout. -- Auto part thickness set-up, 0" - 6" opening. -- Hydraulic feed belt operation of 15 - 45 FPM via 7-1/2 HP hydraulic pack. -- 4-Motor load meters, controls mounted on belt loading side. -- Disc brakes on sanding head motors. -- 30" Infeed load area.

Timesavers Model 1300 Wide Belt Sander 43" x 60" Belts Combination head 439 Hours

TIMESAVER 3345-23-001 (3300 Series) Wide Belt Sander36" Width cap, 4- Head Bottom + 4- Head TopHead Configuration (Bottom + Top): 1st Head: Rubber covered serrated 11″ drum, Duro 80-90, 40 HP motor, 5,250 SFPM.2nd Head: Rubber covered serrated 11″ drum, Duro 80-90, 30 HP motor, 5,250 SFPM.3rd Head: Rubber covered serrated 11″ drum, Duro 65-75, 30 HP motor, 5,250 SFPM.4th Head: Dual Action 7″ Combination head, Duro 50-60, Platen width 3", 25 HP motor, 2,800 SFPM.Specifications: The feed is VFD controlled from 15 - 45 FPM and features a centralized control panel with digital thickness readout -- Auto set up device for thickness. -- Conveyor Vacuum Bed. Double infeed and outfeed hold-down rolls. -- 37" X 75″ Abrasive belt sizeEquipped with & Features: Main motor load meters/Watt meters. -- Four bed jack screws.. -- Disc brakes on main motors. -- Motorized lift with 0 - 5″ -- 14″ infeed loading area and 15″ minimum part length.

Timesavers model 1321-14-01 Wide Belt Sander Max Working Width: 36" Bed Opening: 0-5" 1st head contact drum 2nd head combo head Voltage: 230/60/3 phase

Reconditioned Torit 156RF10 baghouse

Dust Collection System

TORREDA HIDROPAL-1400 COPY LATHE

TORREDA TORMADEX S.A. PA-1200 Hydraulic Wood Turning Back Knife Lathe:Nicely equipped Spanish lathe with dual hydraulic tracers for making quick work of all your demanding woodturning production runs! ... Great for turning baseball bats!Specifications: -- 47" Max. between centers, 9-7/8" max. dia. without traveling steady. -- 3-1/3" Max. dia. through steady rest (larger dia. of 6.2" cap. OPTIONAL); -- High speed automatic loading, feeder accepts pieces up to 4" square. -- 4 HP Motor with (4) turning speeds, 1,200, 2,800, 3,500, and 4,550 RPM. -- (2) HIDRO "T-75" hydraulic reproducing heads with 3" stroke. -- (2) Top mounted hydraulic knives for tenon or pattern cutting (accepts form tools up to 3" wide). -- 2 HP Hydraulic pump motor with (3) carriage feed speeds. -- Features: Pressure sensitive Hydraulic tailstock with Pressure Regulating Valve needed for small, slender turnings to avoid buckling. Pre-rounding tool in front of travelling steady rest. -- Includes: Safety guard, tooling with several roughing and finishing knives.

TRAVAINI TRO 400S-1A 25 HP Liquid Ring Vacuum Pump: -- 25 HP, Liquid ring, single-stage vacuum pump. Nominal capacity 380 ACFM and max. Vacuum 28" HgV. -- Pump materials include cast iron housing, ductile iron impeller and stain less steel shaft. Shaft seals are carbon face with viton elastomers. -- 25 HP, 230/460 Volt, 3-Phase, 60 Hz, TEFC monoblock motor assembly for direct drive, no field alignment needed. -- Sealing fluid re-circulating system includes reservoir of carbon steel with fluid level gauge & drain, high efficiency discharge separator, and over-sized heat exchanger; high temperature switch to protect against over-temperature operation. -- Complete with charge of Dynalube fluid. -- Suction line accessories include: Inlet check valve, vacuum gauge (0 - 30" HgV), inlet filter assembly, manual unloader valve, and vacuum relief valve. -- Heat exchanger is air cooler type made from aluminum and extended surface fins. -- Electrical controls include: Starter/overload reset, pump running light, hour meter, hi-temp light, terminal blocks mounted in a NEMA 12 cabinet.

TRAVAINI TRO 500S-1A 40 HP Liquid Ring Vacuum Pump, 13,920 Hours:Nominal capacity 500 ACFM @ 20" HgV; max Vacuum 27" HgV.Specifications: -- Pump materials include cast iron housing, ductile iron impeller and stain-less steel shaft. Shaft seals are carbon face with viton elastomers. -- 40 HP, 440 V, 60 Cy, 3 Ph., TEFC monoblock assembly for direct drive, no field alignment needed. -- Sealing fluid re-circulating system includes reservoir of carbon steel with fluid level guage and drain, high-efficiency discharge separator and oversized heat exchanger. -- High temp switch to protect against over temp operation.- Complete with a charge of Dynalube fluid. -- Suction line accessories include inlet check valve, vacuum gauge (0 - 30" HgV), inlet filter assembly, manual unloader valve, and vacuum relief valve. -- Heat exchanger is air cooler type made from aluminum and extended surface fins. -- Electrical controls include: Starter/overload reset, pump running light, hour meter, hi-temp light, and terminal blocks, all mounted in a NEMA 12 cabinet.

Tri State Machinery Straight Line Rip Saw S/N 4.5.74-72

Custom Ceiling / Flooring Table Table Size: 32' x 6'9" to 14'3" Table Operated by Both Push Button and Key Fob Controls Floor can be built manually on the table Clamping Stud Locators at 16" & 24"

Twin City Fan Blower Air Lock Can BE Added For Additional Cost

TWIN FLOW Air Make-Up Unit 14,000 CFM. Vertical mount with Remote Control Panel: -- CFM: 14,000 CFM @ 1.75" ESP, 10 HPTEFC motor -- BTU: 1.38 MBTUH -- Burner: MAXON burner -- Temperature Control: 80º F temperature rise in spray cycle -- -- Mounting: Vertical, outdoor/indoor mounted -- Fuel required: Natural gas, 0.3 PSI pressure -- Intake/Discharge: Vertical, screened, air intake with vertical discharge -- Filter Sections: V-Bank style with 1’’ cleanable air intake disposable type filters -- Gas Control: Control cabinet and pre-piped gas combustion system mounted on burner section to FM, Electronic Modulation -- Specifications includes: Digital Temperature Controller, ON/OFF & Summer/Winter Switch, pressure regulator, metering valve, pilot pressure regulator & pilot gas valve, flame rod, high limit switch, air flow switch, power transformer, ignition transformer and spark plug -- Electrical Control cabinet includes: main breaker disconnects, magnetic motor starters with adjustable overload protection for air makeup, motor fuse protection -- Enclosure Design: Framed, with 18 ga. metal walls and 1" insulation -- Note: Available in Horizontal and Vertical mount. Please inquire. -- Also available: Controls option: - Two stages for 14,000 or 7,000 CFM at extra cost of about $3,000.

TWIN FLOW Air Make-Up Unit 7,000 CFM. Vertical mount with Remote Control Panel: -- CFM: 7,000 CFM @ 1.75" ESP, 5HP/575v/3ph/60Hz TEFC motor -- BTU: 0.68 MBTUH -- Burner: MAXON burner -- Temperature Control: 80º F temperature rise in spray cycle -- Mounting: Vertical, outdoor/indoor mounted -- Fuel required: Natural gas, 0.3 PSI pressure -- Intake/Discharge: Vertical, screened, air intake with vertical discharge -- Filter Sections: V-Bank style with 1’’ cleanable air intake disposable type filters -- Gas Control: Control cabinet and pre-piped gas combustion system mounted on burner section to FM, Electronic Modulation -- Specifications includes: Digital Temperature Controller, ON/OFF & Summer/Winter Switch, pressure regulator, metering valve, pilot pressure regulator & pilot gas valve, flame rod, high limit switch, air flow switch, power transformer, ignition transformer and spark plug -- Electrical Control cabinet includes: main breaker disconnects, magnetic motor starters with adjustable overload protection for air makeup, motor fuse protection -- Motor Control: Control cabinet includes: main breaker disconnects, magnetic motor starters with adjustable overload protection for air makeup, motor fuse protection -- Enclosure Design: Framed, with 18 ga. metal walls and 1" insulation -- Note: Available in Horizontal and Vertical mount. Please inquire.

TYLER - 51″ x 51″: Power Pod Cold Press51" x 51"; End loading; segmented platen Cold Press. -- (4) Individually actuated upper platens: 25" x 25". -- (16) Air bags total: (4) Per platen with approx. 80 PSI. -- Fixed opening with: 36" Daylight; bags have (an almost) 6″ max. stroke; it has a set of: 24″ Steel risers to bring the daylight down to 12″. -- Spring-loaded lower rolls; helps aid in loading & unloading.Rolls currently set below bottom plate; not being used. -- Press with: Air powered; only uses 115 V to activate the bags via: Solenoid switches; each with platen having its own switch.

--In Auctions; https://exfactoryauctions.com/Detail/DL-230113/event/A122024$1 - NO RESERVE -- TYLER French-Type Dovetail Machine Equipped with: (2) 14-1/2” x 17” Tables. (2) 2 HP Routing heads for mounting of drawer sides. (1) 2 HP Grooving head for drawer bottom dado, (2) 2-Spindle Vertical boring heads for drawer hardware. (2) Pneumatic hold-down clamps

40? deep X 87.5? wide capacity. The Maximum opening is 49.5? and the pods will extend 9.5? for a minimum opening of 40?. The press is rated to 100 PSI and has (1) pod short of 100% pod coverage. That being the center bags are staggered. There are spring loaded bed rollers to aid in loading and unloading. The top and bottom plates are dent free and no air leaks This fully functional machine has been fully cleaned and checked and is ready to work..