Woodworking Equipment For Sale

KILLINGER KM-150 Bench-Top Flute & Barley Twist Machine for Right & Left-Hand Barley Twists & Straight FlutingsSpecifications: -- Maximum workpiece diameter 200 mm (7.87"), Maximum milling length 1,650 mm (64.96").Equipped with: -- 24-Position Indexing plate.Complete with: -- Legs.NOTE: No Router.Dimensions: 81" x 19" x 48" H.Weight without Legs: 110 Lbs.

This Kimwood Panel Master Sander is in good working/running condition and it is ready to load! - 48" Feed - Feed speeds up to 200 lineal feet per minute - (2) opposing heads - 250HP - (2) operator control panels - Many spare parts including sanding belts

Table Configuration: • KOMO VR 512 Mach I CNC Router • 60 x 144" Cast aluminum machined vacuum table • Table has been designed for High Flow vacuum pump • Ideal for nested based manufacturing • Heavy Duty fixed Gantry Bridge • A-Frame style Gantry Support legs • Pop up part locating pins (set of three pins) Head Configuration: • 12 HP High Frequency 4-pole Router Spindle • Programmable spindle speeds from 9,000 - 18,000 RPM • 8-Position Dynamic tool changer with BT-30 tool holders • (6) Vertical drill spindles on 32 mm centers • (4) Horizontal boring spindles with 1 + 1opposing in the X-axis and 1 + 1opposing in the Y-axis Positioning: • All axes are positioned by AC Servo Drives • Heavy Duty Profiled machine rails and bearing trucks • Preloaded precision ball screws for positioning • Automatic Lubrication system to all bearings • Rapid travel speeds of 1,250 IPM on both the X and Y-axes • Travel speeds of 600 IPM on the Z-axis Controller: • FANUC 210i PC Front end Controller • Windows Operating system • RS-232 Serial interface • 3-axis simultaneous control • Feed rate override • Spindle speed override • Hand help pendant • Remote operating pedestal with vacuum and cycle start buttons, pop up pins, as well as emergency stop.

Komo VR512 CNC Router Fanuc Controls SN 24129-03-01-93 Quincy Vacuum Pump

Komo VR508 CNC Router 60" x 120" Table 25 HP Sullair Vacuum Pump Dust Collector (10 or 15 HP - need to confirm) (2) Two main router heads with Quick Change (2) Vertical Drill Units (1) 8 HP 10" Saw Fanuc Control

KOMO MHS AUTOMATIC VACUUM PANEL FEEDER: -- Specifications: Single vacuum Infeed & Rake-Off system for Nested Based CNC Router operation.Designed for loading of a 5' x 10' (61" x 128") panel cap. CNC Router and can handle material up to that size; Load/Rake cycle time is approx. (25) Seconds. -- Operating Process:A fully Automatic sheet Feeder and Unloader. Designed for a single bunk application and the ability to load from 3 sides.As it moves the sheet over the router table the previously nested parts are pushed onto a conveyor or sorting table, the dust is cleaned from the router table by the dust collection on the front of the gantry and the new sheet is Squared up on the router table.Full Bunk of material is loaded into staging area constructed of tubular steel with cross-support and safety guides to properly position bunk, preventing damage by Forklift operator to loader base.Loading is performed via a vacuum cup system with (4) rows of adjustable vacuum cups, (2) cups per row; front-to-back spacing is fixed and cups are adjustable left-to-right.Material is picked up from the top of the stack and loaded onto the router table, pusher arms at front & right side square the material onto the table.After machining, the vacuum lift picks up another sheet for processing; as it brings it over the side, squaring arm rakes the processed panel and skeleton onto a side table. PLEASE NOTE: This unit will need to be integrated with the controller of your current CNC Router. Actual Model is KOMO MHS.

//This machine is in an Auction on exfactoryauctions.com// //Link to machine: http://exf.ac/i63 The Flex Series of CNC routers from Komo Machine has been developed specifically for the customer who expects the utmost in technical quality and reliability at an economical price. These machines feature a moving gantry configuration and a side-mounted tool changer. Features: Four-pole, 16HP (12kw), 24,000 RPM, HSK 63F, fan-cooled spindle, 12 position automatic tool changer with aggregate capability, Air blast for optimal dust/chip evacuation and cooling of the cutting tool, Advanced Fanuc HVI servo system tuned for optimum acceleration and deceleration, Fanuc Panel i control with integrated PC 19" color display Construction, FEA "Finite Element Analysis" engineered structure, Heavy-duty steel fabrication Specifications Spindle: 1 Spindle RPM 16HP (12kw), four-pole, fan cooled Up to 24,000, fully programmable with HSK 63F taper. Table: 60" x 144" (1524mm x 3658mm), Four (4) 1" (25mm) part location pins Aggregate-Capable Tool Changer: Max 12 tools, Max Dia. 3.25" (82mm) positions full; 6.5" (165mm) adjacent positions empty, Max weight 12 lbs each / 80 lbs total (5.4kg / 36.4kg) Max Length 5" (127mm) Feed Rate/Traverse: X-Axis 2500ipm (63.5mpm), Y-Axis 2500ipm (63.5mpm) Z-Axis 1200ipm (30.5mpm), Acc/Dec83.3 in/sec² Axis Travel: 149" (3784mm) x 82" (2082mm) x 8.5" (215mm) Positioning: ±0.0008" (0.02mm) linear axis repeatability accuracy Control System: Fanuc Panel i With integrated PC and 19" color display Dust Collection Interface: 6" (152mm) diameter (recommended volume 900 cfm) Includes: Dekker Vacuum Pump NOTE: The above specs are taken from literature and considered accurate. As always please take advantage of the inspection period to verify. Items seen in the background are NOT a part of this Lot.

KRAMER K2024-1U -- K20 Series system is a heavy-duty barrel tumbler with standard capacity of 4.80 cubic feet. -- K20 system is a deburring machine solution that features a timer, variable speed, a heavy chain drive, and removable, interchangeable barrels. -- This deburring turn-key machine can configured to handle (1) to multiple barrels at a time. The barrels are mounted in a cradle and can be interchanged to divide up the load. -- Includes (1) Unlined barrel -- Variable speed control 25 - 50 RPM; 24-Hour timer; Start-stop switch. -- Complete unit dimensions are 58" W x 32" D x 50" H.

The K14 Series system is a small, heavy-duty, bench-top, barrel tumbler with standard capacities ranging from 0.75 - 1.5 cubic feet. -- The K14 system is a deburring machine solution that features a timer, variable speed, a heavy chain drive, and removable, interchangeable barrels. -- The barrels are mounted high enought to allow a screen and pan underneath so the barrel can be emptied without lifting and dumping. -- This deburring turn-key machine can handle loads of up to 200 Lbs. The barrels are mounted in a cradle and can be interchanged to divide up the load. -- (1) Steel barrel lined with a durable Polyurethane lining; 14" diameter across corners by 22-1/2" wide; Quick action lock on covers, solid, watertight doors. -- Variable speed control 25 - 50 RPM; 24-Hour timer; Start-stop switch. -- Complete bench-top unit dimensions are 44-1/2" W x 25" D x 24" H.

Pneumatic Single Spindle Tabletop continuous operation drill;Specifications: -- 1.25 HP direct drive pneumatic motor; 8" tabletop working height; 1 Sec cycle time. -- Drills the pocket hole with a 3/8" dia. step bit in (1) smooth operation; the bit is supported all the way to the workpiece by a hardened steel drill guide that ensures tear-out free holes and consistent placement in virtually any material. -- Capacity: Materials from 1/2"- to 1-1/2" thick.Features: -- Pneumatic drill motor, pneumatic clamping. -- 15° Boring angle for greater stability, reduced screw breakout & splitting; this produces a smaller "flat-bottom" pocket hole with rounded sides that can be plugged with a dowel if desired.Includes: -- External regulator, filter & lubricator, 3/8" cobalt drill bit, and foot pedal actuation.Requires a compressor able to produce 8 CFM at 120 PSI (50% duty cycle).

KREG DK 3100 Pocket Hole Boring MachineElectric 3-spindle Pocket Drill; 1.5 HP direct drive electric motor; 39-1/2" table/ top working height; (0.5 - 1) Sec cycle time. -- Drills (2) pocket holes in (1) machining cycle across rails of varying widths with 3/8" dia. step bit in (1) smooth operation.... Drill spindles in the machine are fixed at 3/4" - 1" and 1-3/4" on center allowing it to handle most common rail widths of 1-1/2" up to 3-3/4" with ease. -- One of the (3) Spindles is with left-handed, simply remove one bit from the spindle not being used to set the desired 2-hole spacing. -- The bits are supported all the way to the workpiece by a hardened steel drill guide that ensures tear-out free holes and consistent placement in virtually any material. -- Features: 15° Boring angle for greater stability, reduced screw breakout & splitting. This produces a smaller "flat-bottom" pocket hole with rounded sides that can be plugged with a dowel if desired. -- Includes: Pressure gauge & cycle counter, fence, holddown & clamping assembly, (2) 3/8" cobalt drill bits, and foot pedal control.

Electric Single Spindle Pocket Drill. Specifications: -- Capacity: Materials from 1/2"- to 1 1/2"-thick. -- 1.5 HP direct drive electric motor (also available 1.5 HP direct drive pneumatic motor); 40" table top working height; 1 Sec cycle time. -- Drills the pocket hole with a 3/8" dia. step bit in (1) smooth operation. The bit is supported all the way to the workpiece by a hardened steel drill guide that ensures tear-out free holes and consistent placement in virtually any material. -- Electrical: 110 VAC, Pneumatics: 90 PSI, recommended for clamping. -- Dimensions: 50"H x 24"W x 24"D (40" table height), 176 lbs.Features: -- 15° Boring angle for greater stability, reduced screw breakout & splitting. -- This produces a smaller "flat bottom" pocket hole with rounded sides that can be plugged with a dowel if desired. Includes: -- Pressure gauge & cycle counter, fence, holddown tower, (1) 3/8" cobalt drill bits, and foot pedal actuation.

Pneumatic Single Spindle Pocket Drill;Specifications: -- 1.25 HP direct drive pneumatic motor; 40" table top working height; (0.5 - 1) Sec cycle time. -- Drills the pocket hole with a 3/8" dia. step bit in (1) smooth operation. -- The bit is supported all the way to the workpiece by a hardened steel drill guide that ensures tear-out free holes and consistent placement in virtually any material. Pneumatics: 120 PSI recommended. Features: -- 15° Boring angle for greater stability, reduced screw breakout & splitting. This produces a smaller "flat-bottom" pocket hole with rounded sides that can be plugged with a dowel if desired. Includes: -- External regulator, filter & lubricator, (1) 3/8" cobalt drill bit, and foot pedal actuation. Just add $150 to the price of the machine for shipping.

KUFO SK-12RS Straight Line Rip Saw w/Return Conveyor;Entry level Straight-Line Rip Saw with a guaranteed 6' glue line. -- Powered by a 15 HP direct drive motor. -- 12" Dia. Blade capacity for up to 3-1/4" max. cutting height, 4,200 RPM blade speed. -- Equipped with (6) holddowns and a Wye-Delta soft start for lower amp requirements during start-up. -- 1 HP Feed motor, 36 - 145 FPM feed speed, 6" chain width and automatic chain lubrication. -- Treated chain links, pins and raceways withstand heavy use because of an automatic oiler. -- Large 15-3/4" rip capacity. -- Overarm control box mounted on the in-feed side. -- Total space requirements are about the same as a standard size tablesaw. -- Complete with side mounted return conveyor.

Oscillating Edge Sander with end sanding kit. -- 6" Wide x 89" long abrasive belt. -- Tilting 6" x 24" platen. -- 3 HP, single or 3-Phase motor w/emergency switch. -- 6" Diameter drive pulley. -- 8" x 24" Front table with a 4" vertical adjustment and miter gauge. -- End table for radius work. -- Heavy tables, fabricated steel base and dust hood. -- 3-Phase unit model # is SK-3000SDN3.

Single belt oscillating "Tiltable Bed" 0° - 90° sander, 3 HP main motor, 3,400 RPM, belt size 6" x 89", 30.5" long platen. -- Max sanding length 30.5", 4" vertical adjustment of front table, 36" table height, oscillating rate of 121 times/min. -- Includes: (4) interchangable spindles, sizes are 1.25" - 1.5" - 2" & 2.5" dia.

Kuka KR60-3 Robot System KR C4 Control System Kuka Programming Smart Pad Robot Enclosure (3) Heave duty conveyor racks

KUNDIG DUPLEX 53-RC-E Wide Belt Sander (2) Heads; 52" Width cap. Drum, Combination Head.Head Configuration1st Head: 7-1/4" Dia. rubber covered contact roll, 25 HP motor.2nd Head: Combination head with rubber covered contact roll and segmented finishing platen, infeed sensors sense the panel and electronically control the platen height with timers, variable edge control can also be set, 20 HP motor.Specifications: Abrasive belt size 54" x 75" with air tensioning and electronic abrasive belt tracking, both heads with abrasive grit thickness adjustment, 2 HP Variable feed drive. -- Conveyor belt speeds 9 - 45 FPM, controlled by electronic inverter & adjustable on the control panel; infeed & outfeed rubber covered holddown rollers.Equipped with & Features: -- Workpiece thickness cap. 1/8" - 6-1/4", motorized thickness adjustment with LED readout. -- A joystick controls the conveyor opening and start/stop of the feed, automatic "over-thickness" protection and automatic conveyor belt tracking. -- Constant passline of conveyor height at 35". -- Air blow off of second head abrasive belt. -- Emergency stop button, motor load meters, magnetic controls.NOTE from the seller: There is a small leak in the air bladder . The sander has 6,541 working hours

Max. operating width in grain direction approx. 3200 mm Min. operating width in grain direction approx. 600 mm Width of the veneer strips across the grain from approx. 60 mm Veneer thickness approx. 0.3 – 2.5 mm Capacity up to 28 joints/min. Feed speed approx. 30 m/min. Operating voltage 480 V, 3 Ph, 60 cycles

LA NUOVA SCOLPITRICE 201-16 Multi-Spindle Carving Machine.(16) Cutter Stations, 55" max. workpiece length,Specifications: -- (16) Dual carving spindle heads, 8" between spindles, 20" max. working diameter. -- Each head has a roughing & finishing spindle, all heads swivel 360° with pneumatic locking. -- Upper carriage controlled by (2) High Frequency changers allowing (2) motor speeds of 12,000 & 18,000 RPM. -- Pneumatic chucking of material, stock turns 360°. Copy stylus of hardened and ground steel, adjustable for depth on either side. -- Traverse feed of carving heads was patented and requires no maintenance. -- Includes: Lot of tooling. Table for flat/horizontal copying.Note: Machine completely gone over and all heads rebuilt in 2011 and used sparingly since.Actual model is 201-16.