Sanders For Sale

Cemco 2000 Sander, Heavy Duty, 36inch wide, 20 hp, 3 phase, good condition $10,000 - Call 218-638-2810 or 218-410-0548

AEM 137-1 WIDE BELT SANDER1-Head, 36" width cap. - Combination sanding head with 4" dia. rubberized contact roll & 1-1/2" wide "dual action" polishing platen.Equipped with: -- Abrasive belt size 37" x 60" -- Pneumatic abrasive belt tensioning. -- POSI-TRACK electronic abrasive belt tracking. -- 20 HP main drive motor. -- 2 HP Variable feed speed motor for 15 - 45 FPM. -- Infeed & outfeed rubber covered holddown rolls. -- 0" - 6" manual thickness adjustment. -- 24" Infeed conveyor extensions with over thick protection device at infeed,Complete with: -- Air-operated disc brakes on sanding head, emergency stop button

AEM - 502-43-KPS, ...43" Planer Sander -- 1st Head: Helical planer; 25 HP, 208 - 230 - 460V. 3-Phase. -- 2nd Platen Head: 5"; 20 HP, 208 - 230 - 460 V; 3-phase; capacity 43 x 8 inches. -- Variable speed frequency drive. -- Load meters; pneumatic tracking. -- Power open & close.Also included: -- Extra feed belt. -- Original manuals and other documents.

AEM 8 Narrow Belt Sander

AEM 36" Sander

AEM 36" Sander 20 HP main motor Combination head

Alpha Brush KS-LS Sander

The VICTORY machine is a “heavy duty” linear sanding machine, that can be supplied with sanding drums or sanding disc’s depending on the application in the different industries. The machine comes standard with motorized adjustment, but can also be supplied with 14” PLC control with memory, so different programs can be stored & the setup can easily be done. The top/bottom drums comes in diameter of 400mm (16”) & side-heads comes in 300mm (12”) diameter, which will ensure better abrasive life. When machine is supplied with disc’s, each disc is 300mm (12”) in diameter. LS-TS- Offset Heavy duty motorsEasy changing of abrasivesHeavy duty constructionExtra large sanding wheelsTiltable side-heads Thickness of work piece: Min 0mm - max 150mm (6”)Conveyor Roller width: 300mm ( 12” )Conveyor motor: 0,75 kwSpeed of conveyor belt: 3– 15 m/min. ( 9-45 f/min)

Biesse Levia 310-1350 Sander

BIESSE - ARTECH LEVIA 330, ...3-Head Wide Belt Sander43" Width cap. Drum, Drum, and Combination Head.Head Configuration: -- 1st Head: Rubber covered Contact Roll, 6" dia., 25 HP motor. -- 2nd Head: Steel Contact Roll, 6" dia., 25 HP motor. -- 3rd Head: Combination head with a rubber-covered Contact Roll and Finishing Platen.NOTE: There are (2) 25 HP motors; one drives the 1st head and the 2nd drives the other (2) heads.Specifications: -- 44" x 85" Abrasive belts, electronic abrasive belt tracking; all contact rolls with pneumatic seclusion; Head #3 with air belt cleaner. -- EASY PRO "2000 C" Processor with (200) programs, touchscreen for control of Sander functions, thickness opening, feed speed, sequential startup, contact roll seclusion, and abrasive belt cleaner. -- Conveyor belt feed, 11 - 66 FPM variable feed speed, 2 HP feed drive with inverter control. -- 1/8" - 7-7/8" Motorized thickness adjustment with LED readout; automatic part thickness setup.Equipped with & Features; -- Automatic conveyor belt tracking. -- Infeed & outfeed shoes or rubber-covered holddown rolls, infeed panel "over thickness" sensor. -- Electronic brakes on both sanding head motors. -- Infeed emergency stop, 3-roll infeed extension, and motor load meter.

Boarke 43" 2-Head Sander

37” Capacity single head 230 volt 3phase

Manufacturer’s Specification ( to be confirmed) - With its powerful 3 HP motor can delivers the performance professional demand. - Coupled with an industrial quality eccentric oscillation mechanism that delivers more efficient sanding, less tendency to burn and less belt loading. - Heavy duty spring system allows easy adjustment for the front aluminum table for full use of the abrasive surface. - Aluminum auxiliary contour table allow use of 4” idler roller as a drum sander. - 9” Dia. Drive drum, 4” Dia. Idler drum. - 9-1/2” x 48” cast iron platen with graphite pad. - Rugged bearing – assisted belt torsion devise.. - Aluminum table travels 8” and tilts – 5 to 45 degree. - Dual 4” dust ports. Belt speed: 4200 RPM - Sanding belt oscillate distance: 1/4” (6 mm) Motor5HP / 220V / 60Hz Belt Size230 x 3520mmn Frint Table Size (L x W)1210 x 300mm Dust Port 4”

Boarke BKM-43K Wide Belt Sander

BOARKE 43 RK Wide Belt Sander, (2) Heads43" Width cap. Drum, Combination HeadHead Configuration1st Head: Contact Roll for Calibration 10"; Dia. Contact Roll, 85 Shore Hardness Dynamically balanced, 25 HP, 230/460 V, wired 230 V2nd Head: Combination Unit for Finish Sanding with ContactRoll, Pad or Both 5.5 “dia. Contact Roll 55 Shore Hardness, Dynamically balanced, 2.8"; wide Finishing Pad, 20 HP, 230 / 460 V, wired 230 V.Specifications: -- Sanding Units include: Photo electric belt tracking, Large diameter Tension, and Idle Rolls, Rigid Main beams for superior accuracy, 2.8"; Dia. spring loaded hold down rolls Quick release Tie Down Blocks, Y Delta Motor Starters -- Feed System: 4 ea. 5 ton capacity lifting screws, Heavy Duty 3-Ply conveyor belt, Heavy slider bed, machined for accuracy -- Variable conveyor speed from 7 – 45 FPM, Inverter Controlled Variable Speed, 2 HP drive motor, Conveyor belt centering device -- Infeed Roller, Guide Ways provide accurate vertical movement -- Control Panel (Located on Belt Loading Side for convenience) -- Digital Controller positions machine thickness -- Digital Readout in Inches or MM, And ν Buttons micro-adjust thickness in 0.001"; increments, Micro-Adjustment hand wheel for final thickness in 0.001"; increments -- Automatic Thickness Set Up, Motorized Thickness adjustment -- Amp Meter, and Volt MeterEquipped with & Features: -- Over Thickness Shut Off, Body activated safety switch at front of machine -- Door activated safety switches on ALL Doors, Emergency Stops front and rear -- UL / CE approved electrical components -- Disc Brakes on both motors -- Emergency Shut off activated when Air Pressure is too low, Overloads are tripped -- Emergency Stops are activated

BOERE - TKS 900, ...2-Head Top Wide Belt Sanding Machine900 mm (36") Working width; equipped with: (1) Contact roller, (1) Fine sanding pad. Head Configuration -- 1st Head: Rubber contact roller, spirally grooved, Shore hardness 80, diameter 265 mm (10.4"), driven by 18 kW (25 HP) motor. -- 2nd Head: Sanding pad, electronic-pneumatic controlled, 114.7 kW (20 HP); Air blowing unit for cleaning the abrasive belt. -- All heads use abrasive belts size: 910 x 1,900 mm (35.8" x 74.8").Feed System -- Variable feed speed: From 5 - 25 MPM (16 - 82 FPM); 1.5 kW (2 HP) motor. -- Motorized part thickness opening: 3 - 150 mm (0.1" - 6"), driven by 0.12 kW (0,15 HP) motor.Complete with: -- Emergency Stop Systems for abrasive belt breakage and low belt tension. -- Infeed safety bar for operator protection and oversized parts. -- Automatic Star Delta starters, motor load meters. -- Pneumatic belt tension. -- Emergency Stops at the front & back. -- Extended infeed belt, approx. 42" long.Actual model: BOERE "TKS 900".

BOERE - TPK-900, ...Planer Sander w/(2) Heads -- 2-Head, 900 mm (36") width cap.; equipped with: (1) Knife planer head and (1) Rubberized Drum. -- 1st Head. Helical knife planer head with: (4) Spirals of 4-sided carbide inserts, each 14 mm x 14 mm; 20 HP motor. -- 2nd Head. Drum approx. 10" dia. rubber covered contact roll; 15 HP motor; all heads with air-operated caliper type disc brakes. -- Variable feed speed: 13 - 52 FPM; 2-1/2 HP motor; automatic conveyor belt tracking; anti-kickback fingers on infeed; infeed holddown shoes' double outfeed pinch rolls on outfeed. -- Motorized part thickness adjustment: 0" - 6"; LED readout display. Complete with: -- Controls mounted on belt loading side; load meters for each head;, conveyor infeed extension.

50” width drum/drum/platen heads 480 volt 3-phase Bottom and top sanders can be sold separately Pictures coming for bottom sander

Butfering SKO-113C Sander Manufacturer specs (to be confirmed): 53" (1350 mm) working width 54" (1370 mm) abrasive belt width 75" (1900 mm) abrasive belt length 1/8" (3 mm) - 5-7/8" (150 mm) panel thickness Variable feed speed via motor (2 HP) with gear box, 8 - 43 FPM Motorized opening/closing Automatic conveyor belt tracking Controller with soft keys Ability to store up to 50 programs Load meter Two (2) idle infeed rollers Sanding unit Grooved metal roller Segmented platen 7 - 60 FPS variable belt speed 25 HP motor Air jet blower Two (2) hold down rollers

53" 3-head sander 1st head - Drum 2nd head - Combo head 3rd head - polishing head outlet rotary cleaning brush belts 54" x 103" Feed variable 8-43 FPM Controller with color screen Manuals available