Sanders For Sale

EXTREMA ESO-108.1 Oscillating Edge Sander with End Sanding Kit. -- 6" Wide x 108" long belt, with 1/4" oscillation travel -- 6" x 40" Graphite covered platen. -- 1-1/2 HP Single-Phase motor w/magnetic switch. -- 7" Diameter drive pulley, and 3" Idler pulley. -- 8" x 37" Front table with 5-3/4" vertical adjustment. -- Adjustable 12" x 19" End table for radius work with a 5-3/4" vertical adjustment. -- Heavy laminated tables, fabricated steel base and dust hood with 4" dust collection port. -- CFM Requirements: 400. -- Weight: 425 Lbs.

EXTREMA ESO-108.3 Oscillating Edge Sander with End Sanding Kit. -- 6" Wide x 108" long belt, with 1/4" oscillation travel. -- 6" x 40" Graphite covered platen. -- 2 HP Three-Phase motor w/magnetic switch. -- 7" Diameter drive pulley, and 3" Idler pulley. -- 8" x 37" Front table with 5-3/4" vertical adjustment. -- Adjustable 12" x 19" End table for radius work with a 5-3/4" vertical adjustment. -- Heavy laminated tables, fabricated steel base and dust hood with 4" dust collection port.

EZ SANDER EZ-3760 Wide Belt SanderEZ-Sander's are built to with the ability to hold very tight tolerance (+/-.003) side to side when set up properly.Specifications: -- The sanding head is a combination head that consists of a 5" rubber-covered contact drum for the more aggressive sanding and then followed by an adjustable 2-1/2" graphite-covered felt polishing platen for doing very fine finishing sanding using a 37" X 60" abrasive belt. -- The conveyor belt speed is set to run at 10 - 30 FPM and is controlled via AC variable speed unit mounted in the main control panel. Simply adjust the dial setting to your desired feed speed. -- Double infeed and outfeed hold-down rolls are provided to help ensure proper part feeding through the Sander. -- The conveyor table/bed opening has a 0" to 5" opening allowing the operator to sand some parts as thick as 5" and the ability to sand very thin parts as well. -- Power raising and lowering of the conveyor bed is standard. -- Digital thickness display is standard.Complete with & Features: -- EZ Sander is equipped with a state-of-the-art electronic tracking system for the abrasive belt. -- Emergency stop heavy-duty caliper disc brakes bring the sanding head to a stop within 4 to 5 Sec when activated by the machine's safety interlock system. -- Limit Switches on both sides of the abrasive belt to keep the belt from over-travel. NOTE: -- Available in single phase with a 7.5 HP or 10 HP 3-Phase main drive motor. -- Voltage change to 440 Volt ...$275.

Sanding wheel shaper for the production of profiles on the sanding wheels. -- Template carrier holds metal or plexiglass template (same as can be used on the moulder knives). -- Spindle length 5" with 1" diameter arbor for wheel support. Handles 8" diameter wheels (3) included with the machine. -- X and Y axis on dovetail slide with lineal bearing support for smooth movement during the wheel grinding. Pneumatic clamping on grinding wheels. Depth of grinding 1.5" for raised panel. -- Tilt capabilities from 0 to + 30°. -- Grinds all types of varda wheels on 1 HP motor with speed of 1,750 RPM. --You can customize this machine to you needs.

G & P - EPN, ... Pump Sander (Double-Sided), -- Double-end direct-drive pneumatic Drum Sander. -- 2 HP Motor - 3,600 RPM motor speed. -- (2) 1-1/4" Dia. x 10" long shafts.

GOODSPEED HF 412 AO Vertical Oscillating Chair Back Sander Specifications: Table size 30” x 30” x 34-1/4” H. Equipped with: 12" W x 25" L Horizontal abrasive belt, with 12” H x 4” Dia. Aluminum & Spiral rubber drums, 12” H x 3-1/2” Dia. Spiral rubber feed drum, with 2 HP Motor & Variable feed speed control. 60 W Feed & Oscillation motors.

GRAINMATIC - CP-960, ...2-Head Wide Belt Sander42" Width cap.; Drum, Platen.Head Configuration:1st Head: Spiral rubber covered contact roll, 7-7/8" dia., 20 HP motor.2nd Head: Combination Head, spiral rubber contact roll, and finishing platen; 15 HP motor.Specifications: -- 36" W x 75" L abrasive belts with air jet tracking. -- Motorized part thickness adjustment with keypad entry and LED readout; 0" - 7" opening. -- Infeed & outfeed spring loaded rubber covered holddown rolls. -- Feed Motor: 3.5 HP -- Variable feed speed: 15 - 60 FPM.Equipped with & Features: -- Infeed emergency stop bar. -- Disc brakes on sanding head motors. --12" Infeed load area. --Volt meters on sanding head motors.NOTE: Some specs need to be verified.

GRIGGIO G 1100 Wide belt Sander2-Head, 1,100 mm (43") width cap. -- 1st Head: Rubber covered steel contact roll, duro 85, 220 mm diameter . -- 2nd Head: Rubber covered contact roll duro 50 -- 25 HP motor to drive both head. -- 43" x 85" abrasive belts, electropneumatic abrasive belt tracking, -- Conveyor belt feed, two speed from control panel at 15 and 30 FPM, 0.4/0.7 HP feed drive, automatic conveyor belt tracking, -- 1/8" - 6-1/2" motorized thickness adjustment with LED readout & 0.75Hp gearmotor drive. --Automatic positioning of the working table, rubber covered spring loaded pressure rollers, double infeed and outfeed rubber covered rolls, infeed panel "over-thickness" sensor. --Two suction dust hoods dia. 6" (150mm),

GRIZZLY H2934 2-HEAD WIDE BELT SANDER2-Head Wide Belt Sander, 36-1/2" width cap. -- Head configuration: - 1st Head: Rubber covered contact drum; 2nd Head: Combination head with rubber covered contact drum and adjustable platen; Abrasive belt size 37" x 60". -- 0" to 6" Thickness cap., LED digital depth encoder; 14" min. board length and 12" infeed conveyor. -- 1st Abrasive belt surface speed of 3,543 SFPM; 2nd abrasives belt surface speed of 2,554 SFPM. -- Conveyor speed from 14 - 60 FPM. -- 20 HP - 50/25 Amp Sanding motor; 1 HP - 3.4/1.7 Amp conveyor motor; 0.25 HP - 1.2/0.6 Amp table lift motor. -- Complete with: Rubber covered holddown rolls, adjustable felt platen, Amp/load meter, and disc brake for emergency stop.

GRIZZLY G5394 STROKE SANDERModel G5394 - Motor 3 Ho - Volt 220 - HZ 60 - Phase 1 - MFG No M05227 - Date 2008/09SPECIFICATIONS: -- Motor: 3 HP, 220V, single-phase, 17A -- Sanding belt speed: 3500 SFPM --Sanding belt size: 6" x 186" -- Table Size: 58" x 23-3/4" -- Table vertical travel: 24" -- Platen horizontal travel: 59" -- Table lateral travel: 18" -- Drive roller diameter: 8" -- Footprint: 70" L x 30-1/2" W -- Overall dimensions: 93-3/4" W x 38" D x 50" H -- Approximate shipping weight: 690 lbsORIGINAL MODEL NUMBER: CT-1500

24” width capacity 5HP motor 6” drums 11fpm

HEESEMANN MFA-6 Impression ... 3-Head Wide Belt Veneer & Lacquer SanderWorking width 1,350 mm (53") and equipped with (1) Cross Belt sanding unit, (1) Segmented Platen heads and (1) Scotbrite BruchAll heads are equipped with HEESEMANN's patented "CSD" selective pressure adjustment system, roller sensors placed every 32 mm (1-1/4") sense part configuration; pressure for each segment can be pre-programmed to provide less pressure on the outer edges or more in the center if desired. The "CSD" computer control will hold a maximum of (20) programs.Head Configuration:1st Head: Cross Belt sanding unit with CSD® segmented pad system. Inner chevron belt. Inverter controlled motor 15 kW (20 HP). Sanding belt speeds infinitely variable min./max. 2 - 20 m/Sec. (6 - 65 FPS). Cross belt size 4800 x 150 mm (189" x 6"). Blowers for sanding belt cleaning, activated by work piece length.2nd Head: Segmented platten with chevron belt,Longitudinal sanding unit 3 Station: Structuring Brush roller: ScotisBrite Feed System: -- Variable feed speeds infinitely adjustable from 3 to 15 m/Min (9 - 49 FPM). -- Constant pass-line 880 mm (34-5/8"). -- Heavy Duty vacuum hold-down system. Air consumption 25 m3/Min. (880 cfm). -- Part thickness min./max. 3 - 150 mm (1/8" - 6"). -- Integrated over-thickness protection. -- Roller table at infeed.Equipped with: -- Industrial PC. 10.4" LCD-TFT Colour-Display with memory for 100 programs. Touch screen. Windows® XPE Operating System. -- Including Energy Management System EMS. -- Automatic tensioning & tracking. -- Electronic brakes on all sanding heads. -- Emergency stop at machine infeed and outfeed. -- Dust extraction hoods 160 mm (6-5/16") diameter.Work-Piece Specifications: -- Thickness min./max. 3 mm / 150 mm (1/8" to 6"). -- Width max. 1,350 mm (53").Machine Frame: -- Welded steel structural frame. Low vibration and torsion resistant.CE compliant.HEESEMANN MFA-6 Impression ... 3-Head Wide Belt Veneer & Lacquer Sander

LSM 8 2 head wide belt sander · 1st Head: Segmented cross-belt, 5/8" wide segments (86 total) with "CSD" control, abrasive belt size 5.9" x 244", (5,400 mm X 150 mm ) inside chevron belt 5.9" x 191", sanding belt speed 5-12 m/s with 17 HP motor. (Inverter controlled) · 2nd Head: Combination head, with segmented polishing platen, 5/8" wide segments with CSD control, 17 HP motor, 106" x 53" ( 2,620 mm X 1,350 mm ) abrasive belt size. (Inverter controlled) Cleaning brush Vacuum bed

Heesemann MFA 10 Wide Belt Sander

HEESEMANN MFA-8 D Wide Belt Sander (4) Heads; 53" Width cap. Veneer/ Sealer Sanding Wide Belt.Great Lacquer/Sealer sander with: (2) Segmented polishing platen, (2) Orbital heads, (1) De-nibbing/Polishing brush.Head Configuration: Head 1: Segmented polishing platen, 5/8 wide segments CSD Control, Variable speed abrasive belt with inverter RPM control, 15HP motorHead 2: Segmented polishing platen, 5/8 wide segments CSD Control, Variable speed abrasive belt with inverter RPM control, 15HP motorHead 3: Orbital head with composite/dense fiber loading; 5HP motorHead 4: Orbital head with composite/dense fiber loading: 5HP motor(1) Brush Type head for de- nibbing and polishingSpecifications: -- LCD monitor with graphic display and key pad entry, 20 program capacity, -- Pressure for each segment can be pre-programmed to provide less pressure on the outer edges or more in the center if required.Equipped with & Features -- Air blast abrasive belt cleaner on heads 1 & 2. -- Variable feed speed from 10 to 49 FPM via 2 HP feed drive. -- Motorized thickness opening 1/4" to 3-5/32" max. -- Rubber covered Infeed and out feed holddown rolls.

HEESEMANN MFA-6 Wide Belt Sander with (3) Heads and a Cleaning Brush.Basic Working Capacity: Max. working width is 1,350 mm (53"), thickness opening min./max. is 3 mm - 150 mm (0.118" - 6.0"). - Conveyor belt speed variable from 5 - 15 MPM (16 - 49 FPM); constant pass height of 880 mm (34.65").Features: -- Head Configuration: (2) Steel contact drum heads, (2) "CSD" controlled contact platens, and (1) rotary cleaning brush. -- Belt Handling: Broken belt monitor and automatic infrared belt tracking; intermittent pneumatic belt cleaning device, belt access on the left-hand side. -- Conveyor Belt: High powered vacuum holddown by 8.6 kW (11.5 HP) fan drive motor, automatic vacuum monitoring system. Variable speed by inverter from 5 - 15 MPM (16 - 49 FPM). -- CSD-32 System: Heads #3 & #4 are equipped with HEESEMANN's Patented "Segmented Pad System", Computer Selective Pressure Control from 0 - 150%, precise surface & edge pressure control, edge pressure independent of surface; 2 mm thickness compensation - zero maintenance with sealed enclosure.Sanding Head Configuration: -- 1st Head: Steel Contact Roll, 8" dia., 25.3 kW (34 HP) motor; sanding belt size of 2,150 mm x 1,400 mm (85" x 55"); belt speed is 18 MPS (60 FPS); equipped with belt motor brake. -- 2nd Head: Steel Contact Roll, 8" dia., 17.5 kW (24 HP) motor; sanding belt size of 2,150 mm x 1,400 mm (85" x 55"); belt speed is 18 MPS (60 FPS); equipped with belt motor brake. -- 3rd Head: Sanding Platen, electronically controlled pressure segments to conform to panel size, 17.5 kW (24 HP) motor; sanding belt size is 2,150 mm x 1,400 mm (85" x 55"), belt speed of 18 MPS (60 FPS); equipped with belt motor brake.. -- Cleaning Brush: Outfeed Rotary Panel Cleaning bristle brush, 120 mm (4-3/4) dia., 0.9 kW (1.2 HP) motor, and holddown roller. -- Includes: Outfeed conveyor table, 48" width x 80" length. Large batch of sanding belts.Controls: -- LCD Operating Panel with: Touch-screen and graphical display, (20) memory addresses for sanding head selection, thickness opening, conveyor feed speed, 1-button sequenced starting of sanding motors, and tracking of sanding belt usage. -- Operating Requirements: Electrical is 151 Amps @ 460 Volt; Dust Extraction is 5,800 CFM @ 3" static pressure. Machine weight approx. 7,000 kG (15,500 Lbs). -- Complete With: Extended infeed table with (2) idle rollers, interior lights, emergency and oversize part thickness safety bar, and Manual.

HEESEMANN - LSM 8-5 RRRL, ...53" Wide Belt Sander53" Width cap.: Drum, Drum, Drum, and CSD® Pad.Head Configuration:• Unit 1 - Longitudinal Sanding Unit: Steel contact roller, helically grooved. - Single-speed 48 HP motor, electronic braking.• Unit 2 - Longitudinal Sanding Unit: Rubber-covered contact roller, helically grooved. - Single-speed 35 HP motor, electronic braking.• Unit 3 - Longitudinal Sanding Unit:- Rubber-covered contact roller, helically grooved. - Single-speed 35 HP motor, electronic braking, bi-directional drive.• Unit 4 - Longitudinal Sanding Unit: CSD® Segmented pad system, 2-speed 20/26 HP motor, electronic braking.• Unit 5 - Panel Cleaning Brush: Fiber trimming, 2.3 HP Motor.Specifications: -- Working height: 880 mm (34.64"). -- Workpiece thickness: 3 mm to 150 mm (1/8" to 6"). -- Working width: 1,300 mm (51-1/8"). -- Longitudinal belt: 1,350 x 2,620 mm (53" x 103"). -- Machine voltage: U.S. Electrics 480 Volts, 3-Phase, 60 cycles.Constant Pass LineController: -- Industrial PC. -- TFT Color touchscreen. -- Windows® Operating System. -- (100) Memory addresses for: • CSD® sanding pressure. • Sanding start/stop. • Sanding belt speeds. • Grit sequence indication. • Sanding belt selection - "ON/OFF". • 1-Button sequenced starting for all motors.RS-232 Serial port.RJ-45 LAN Port.Modem with software licenses.For All additional, detailed specs, select the "View Literature" link .

HEESEMANN - LSM 8, ...3-Head Wide Belt Sander53" Width cap. Crossbelt, Combination , and DrumHead Configuration:1st Head: Cross Belt Sanding Unit, 2-speed motor - 19/24 kW (26/33 HP). - Abrasive belt speed: 12/24 MPS (39/78 FPS); Cross Belt (Cloth), 4,800 x 150 mm (189" x 6").2nd Head: Combination Longitudinal Sanding Unit Front retractable roller for light calibrating and segmented pad system for fine sanding; bi-directional sanding; Door-in-Door viewing; 2 speed motor - 31/37 Hp, abrasive belt speed 10/20 mps (33/65 fps3rd Head: Longitudinal Sanding Unit Internal pressure segment belt for finer sanding Inner chevron belt; Inverter driven motor: 26 kW (34 HP); abrasive belt speed: 0.5-16 MPS (1.6-52 FPS); Longitudinal Belt: 2,620 x 1,350 mm (103" x 53").Unit 4: Panel Cleaning Brush, Fiber trimming.Specifications: -- HEESEMANN's LSM-8 Sanders are designed for heavy (2 - 3) shift operations; this Sander is ideal for: Whitewood sanding of veneered panels and panels coated with various sealers. -- The crossbelt removes tape, cuts short fibers that contribute to grain rising, and sands panels with "book-matched" veneer. -- The last sanding unit is equipped with an internal pressure segment belt for an extra smooth finish.Enhanced 16 mm control roller spacing with (3) rollers per segmented pad. -- CSD® Segmented pad system is equipped on all (3) sanding units. -- Pneumatic conveyor belt cleaning. -- Infeed extension with non-driven rollers. --Electronic variable feed speed from 5 - 25 MPM (16-82 FPM). --Workpiece thickness 3 mm - 140 mm (1/8" to 5-1/2").Equipped with & Features: -- Vacuum Table: Only HEESEMANN builds it into the frame for superior holddown! -- Industrial PC controller, Windows® Operating System.Width Capacity: 53"

HEESEMANN LSM-8/3-OSR Wide Belt Finishing Sander, 52" and (3) Heads; Equipped with: (1) longitudinal segmented platen head. and (2) Orbital Platens -- 1st Head: Longitudinal segmented platen head. Segmented Polishing Platen, 20 & 27 HP dual speed motor. electronically controlled segments to conform to panel size,.2620 x 1350 mm (91.4 x 53.2") Sanding belt. - Equipped with HEESEMANN's patented "CSD" selective pressure adjustment system, sensors placed every 16 mm (5/8") sense part configuration; pressure for each segment, to eliminate sand through, can be pre-programmed to provide less pressure on the outer edges or more in the center if desired. The "CSD" computer control will hold a maximum of (20) programs. -- 2nd & 3rd Heads: OSR Dual orbital action head with (1) high-speed orbit on sanding pad, powered by 3 kW (4.5 HP) motor.Secondary oscillation movement of platens powered by 1.5 HP motor. Upstream and downstream vacuum chutes on each head for dust localized dust pickup.- Platens feature "quick change" abrasive material; Both orbital heads with variable speed inverter drives. -- Outfeed Rotary Brush with cleaning brush loading with single end adjustment , 6" max. dia., 3.4 HP motor. -- Variable feed speed from 13 to 82 FPM, 6.5 HP feed drive. -- Infeed and outfeed Ssissor Lift and Control box shown are not included. -- Motorized thickness opening 1/4" to 3-5/32" max. - -- Power Consumption: 63 KW, 75 Amps. -- Separate display console for CSD control.

NOTE: Wide Belt Sander was completely rebuilt for $68,000 in 2019. 53" 4-Head Wide Belt Sander Head Configuration: 1st Head: Spiral rubber contact roll, 45 kW, 460 V; 2nd Head: Spiral rubber contact roll, 44 kW, 420/480 V; 3rd Head: Spiral rubber contact roll, 37 kW, 460 V; 4th Head: Platen design with (2) Smooth steel rollers; Final Station: Rotating air-jet blow-off; 12" Load space, Sensing, Abrasive belt size 1,400 x 3,250 mm (55.12" x 127.95"), T.B. WOODS "E-TRAC WF-2" Sensor-less vector drive for variable sanding head speed Vacuum feed mat, Adjustable fence, VACON Variable speed drive for feed speed, 8.6 kW, 254-277/440-480 V, Electronic belt tracking & Pneumatic motorized thickness control, Approximately 2 HP, 230/460 V HEESEMANN Swivel-mounted touchscreen control Overall dimensions: 164" x 92" x 112" H, Weight: 11,000 kg (24,250 Lbs.) NOTE: Machine is currently in storage.