Woodworking Equipment For Sale

EXTREMA ET-100 Fixed Spindle Shaper; "Extremely" well-built and with solid features. -- Single phase with 3 HP or 3-phase with 5 HP motor. -- Interchangeable spindles of 1-1/4" and 3/4". -- (2) Spindle speeds of 7,500 & 10,000 RPM. -- Heavy cast iron table with a 6" max. table ring. -- Spindle lock, micro-adjustable back fence and reversing switch. -- Miter gauge, 1/2" router collet adapter and cutterhead guard.

EXTREMA ET-120 Spindle Shaper;"Extremely" Well-built and with solid features. -- 5 HP Single-phase motor. -- Interchangeable spindles of 1-1/4" & 3/4" and (1) router collet adapter. -- Dual drive belts and (2) spindle speeds of 7,500 & 10,000 RPM. -- Heavy cast iron table with a 6" max. table ring. -- Spindle lock, micro-adjustable back fence and reversing switch. -- Complete with: Miter gauge, 1/2" router collet adapter and cutterhead guard.

EXTREMA ET-120.3 Shaper w/Fixed Spindle; "Extremely" Well-built and with solid features. -- 5 HP motor. -- Interchangeable spindles of 1-1/4" & 3/4" and (1) router collet adapter. -- Dual belts and (2) spindle speeds of 7,500 & 10,000 RPM. -- Heavy cast iron table with a 6" max. table ring. -- Spindle lock, micro-adjustable back fence and reversing switch. -- Miter gauge, 1/2" router collet adapter and cutterhead guard.

"Extremely" Well-built and with solid features. -- Solid spindle of 1-1/4" with 5-13/16" under nut. -- Dual belts and (3) spindle speeds of 5,500 - 7,500 & 10,000 RPM. -- Heavy cast iron table with a 12-3/8" max. table ring. -- Spindle lock, micro-adjustable back fence and reversing switch. -- Large 7.5 HP motor. -- Miter gauge, cutterhead guard assembly, operators manual, and tool kit.

EXTREMA ET-160 Fixed Spindle Shaper;"Extremely" Well-built and with solid features.Specifications: -- Solid spindle of 1-1/4" with 5-13/16" under the nut. -- Large 10 HP motor. -- (3) Spindle speeds of 5,500 - 7,500 & 10,000 RPM. -- Heavy cast iron table with a 12-3/8" max. table ring. -- Spindle lock, micro-adjustable back fence, and reversing switch. -- Miter gauge, cutterhead guard assembly, operator's manual, and tool kit.

37" width capacity Single head 60" belt length Digital thickness controller Electronic belt tracking vVariable speed drive

EXTREMA XP-615AZ Single Sided Head PlanerSpecifications: -- Width: 24" -- Main HP: 15 HP -- Feed HP: 1 HP -- Elevation HP: 0.5 HP -- Max. Thickness: 8.75" -- Min. Thickness: 0.375" -- Max. Cut: 0.25" -- Min. Length: 10.5" -- Cutterhead Speed: 6000 RPM -- Feed Speed: 20-42 ft/min -- Air Requirements: 1000 CFM -- Thickness Adjustment: PLC ControllerBed Roller Adjustment: External -- Powered Bed Rollers: Top and Bottom -- lnfeed Roller: Standard -- Amps (230V / 460V): 41A/20A -- Weight: 2345 LbsFeatures: -- Solid cast-iron construction -- Sectional infeed rollers -- Huge 8-3/4"thickness capacity -- 6000 RPM cutterheads -- Anti-kickback fingers -- Segmented chip breakers -- Sectional feed rollers -- XP-615 Digital Controller -- Motorized table elevation -- Available with straight, STEALTH, or ilECTDFi cutterheads -- Heavy duty screwjack elevation system -- Easy access internal workings -- External bed roller adjustmentsOptional: -- In-feed Roller

EXTREMA XS-1E43 Single Head Wide Belt Sander42" Working width, up to 5" max. opening with electronic digital microprocessor thickness control.Equipped with: -- Rubber-covered contact drum and 2-1/2" wide finishing platen, 25 HP main motor; -- 43" x 60" Abrasive belt, TRU-TRAK solid-state electronic belt sensing with pneumatic tracking. -- GOODYEAR Endless conveyor belt with pneumatic tracking, 2 HP variable speed feed motor from 15 - 48 FPM. -- 0.5 HP Motor to raise & lower table via (4) jack screws, an over-thickness bar at the infeed of machine, and AUTO-SET thickness device. Complete with & Features: -- Double infeed & outfeed rubber covered holddown rolls. -- Air operated disc brakes on main motor, front & rear emergency stop buttons, and motor load meter. -- SQUARE D Electrical controls; magnetic Starter with overload protection, and electrical interlock at sanding belt access doors.NOTE: Also available wired for ...460V operation.

EXTREMA PERFORMA XS-2P52 Wide Belt Sander (2) Heads;52" Width cap. Drum, Roller and Platen - 75"; Belt Lengths Head Configuration: -- 1st Head: Contact drum 30 HP motor; -- 2nd Head: Roller and Platen 30 HP motor.Features: -- Over thickness safety device -- Infeed bed rollers -- Digital thickness controller -- Individual amp meters -- Disc brakes on sanding heads -- Telemecanique electrics. -- Camozzi pneumatics -- Variable speed drive system.Specification: -- Feed motor 3 HP -- Elevation motor 0.5 HP -- Max. thickness 6" - Min. thickness 1/8" -- Contact drum 1st head 8" dia. -- Roller drum on 2nd head 5" dia. -- Dust Collection requirements 4800 CFM -- Feed speeds 15 - 50 FPM. -- Weight 6500 Lbs -- AMPS (220 V / 460 V ) 148/74.

EXTREMA EXCESS XS-1E37 SINGLE HEAD WIDE BELT SANDER37" Width capacity, 0" to 6" conveyor bed opening. Mono-block construction for solid, vibration free operation and increased durability. -- Equipped with: Combination sanding head with rubber covered contact roll & graphite covered platen. -- Over thickness material feeding safety device. -- Digital material thickness controller setting with LED readout accurate to a thousandths of an inch. -- "Automatic Thickness Setting" device for easy setup. -- OMRON Electronic abrasive belt tracking. -- GOODYEAR Endless conveyor belt with automatic belt tracking. -- 20 HP Main motor. -- REGAL Variable feed speed drive unit; 2 HP motor. -- 1/2 HP Power elevation motor. -- Large cabinet style doors for easy service access. -- Pneumatic abrasive belt tensioning. -- Double infeed & outfeed covered holddown rollers. -- Infeed conveyor extension with safety stop bar, emergency stop button and motor load meter. -- Operations manual & free box of 3M Sanding Belts. -- Optional 460 Volt / 3 Phase.

EZ SANDER EZ-3760 Wide Belt SanderEZ-Sander's are built to with the ability to hold very tight tolerance (+/-.003) side to side when set up properly.Specifications: -- The sanding head is a combination head that consists of a 5" rubber-covered contact drum for the more aggressive sanding and then followed by an adjustable 2-1/2" graphite-covered felt polishing platen for doing very fine finishing sanding using a 37" X 60" abrasive belt. -- The conveyor belt speed is set to run at 10 - 30 FPM and is controlled via AC variable speed unit mounted in the main control panel. Simply adjust the dial setting to your desired feed speed. -- Double infeed and outfeed hold-down rolls are provided to help ensure proper part feeding through the Sander. -- The conveyor table/bed opening has a 0" to 5" opening allowing the operator to sand some parts as thick as 5" and the ability to sand very thin parts as well. -- Power raising and lowering of the conveyor bed is standard. -- Digital thickness display is standard.Complete with & Features: -- EZ Sander is equipped with a state-of-the-art electronic tracking system for the abrasive belt. -- Emergency stop heavy-duty caliper disc brakes bring the sanding head to a stop within 4 to 5 Sec when activated by the machine's safety interlock system. -- Limit Switches on both sides of the abrasive belt to keep the belt from over-travel. NOTE: -- Available in single phase with a 7.5 HP or 10 HP 3-Phase main drive motor. -- Voltage change to 440 Volt ...$275.

Fanuc Robot with Controller Box and Teach Pendant Model: S-420iF Type: A05B-1313-B501 Part #: R98Y03430 Date: 1998.11

45 KVA 480 volt to 208Y/120

FELDER FORMAT 4 - C-EXPRESS 920 CNC MACHINING CENTER (FEED THRU W/ROUTING): -- Specifications: Automatic CNC Feed Through Point to Point Boring Machine that combines flexibility and high productivity.A perfectly suited solution for small to midsize companies & artisans in need of an automatic solution for precision drilling with a low cost investment.Parts can be discharged at the opposite end of the machine for automated material handling or returned to the Operator for manual unloading. -- Working Field:Max. panel size on X-Axis 118" (3,000 mm); Y-axis is 36.2" (920 mm); Z-axis is 2" (50 mm).Min. panel on size X-axis is 11" (280 mm); Y-axis is 7.1" (180 mm); Z-axis is 0.4" (10 mm).Max. Panel weight 66 Lbs (30 kG). -- Positioning Speed: Panel feeding speed of 229 FPM (70 MPM), Y-axis at 229 FPM (70 MPM), Z-axis at 65 FPM (20 MPM).Axes positioning by AC drives & brushless Servo motors; the Panel moves in X-axis & the boring head moves in Y- & Z-axes. -- Work Area:NC Controlled "Optical Laser Sensor" creates a zero-panel reference point by reading the panel's ends; this ensures that RH & LH (mirror image) panels will always be symmetrical.High precision clamping automatically positions the workpiece. Automatic presser moves independently and adjusts to workpiece thickness. Pneumatic side pusher makes locating workpiece accurate and efficient. LH Side pressure clamp with automatic adjustment & pneumatic locking according to the panel width.Scratch resistant rollerball table makes for ease of loading parts into the machine. -- Boring Unit:3 HP (2.2 kW) Motor, variable speed from 4,500 - 8,000 RPM.(9) Independent vertical spindles on 32 mm centers: (5) Spindles in X-axis & (4) spindles in Y-axis.(6) Horizontal spindles with: (2 + 2) in X-Axis & (1 + 1) in Y-axis.(1) X-Axis grooving saw for max. 120 mm dia. blade, variable speed from 5,500 - 10,000 RPM. -- Machining:5 HP (3.7 kW) Motor, variable speed from 1,000 - 18,000 RPM with ER 32 adaptor & manual tool change system. -- Operator & Machine Control: PC-Based user-friendly icon driven Control housed on the main machine base + "WOODFLASH" Operating System. 19' LCD Displays programming graphics, functions, machine data. -- Complete with: User & Maintenance Manuals; handheld pendant. -- Options Include: &#9679 Special side clamping device for min. panel size in Y-axis of 2-3/4" (70 mm). &#9679 Additional retractable infeed support table with roller balls. -- Actual model is: FELDER FORMAT 4 - C-EXPRESS 920 CLASSIC

Felder Format 4 Tempora 60.16L Edgebander

Felder Creator 950 Premium CNC Center

Felder Format 4 Edgebander Model: Tempora 6012

Felder Creator 950

Felder Profit H10 CNC Router (2) Vacuum Pumps 7.5 HP Tool Changer Outfeed Conveyor

Felder Profit H10 CNC Router (2) Vacuum Pumps 7.5 HP Tool Changer Outfeed Conveyor