Woodworking Equipment For Sale

CEMCO - URF-3352, ...3-Head Wide Belt Sander.53" Width cap. Drum, Drum Combination Head.Head Configuration:1st Head: Rubber-covered contact roll, 10" dia., 65 shores (to be verified), adjustable with a dial indicator, 50 HP motor.2nd Head: Rubber-covered contact roll, 10" dia., 65 shores (to be verified), adjustable with a dial indicator, 40 HP motor.3rd Head: Combination Head, (2) 5-1/2" finishing Drums & Platen.4th Station: Panel Brush.Specifications: -- 6" Max. working thickness. -- 1 HP Variable speed feed. -- 53" x 75" Abrasive belt size. -- Power raise & lower of feed bed. -- Numerical digital readout of thickness. -- Spring-loaded holddown rollers through machine. -- 36" Infeed table, 30" outfeed table; feed speeds from 5 - 60 FPM, 3 HP inverter. -- Load meters. -- (2) 8" Dia. dust outlets. Equipped with & Features: -- Belt Tracking (Electric Eye). -- Constant Pass-Line machine.Some spec's need to be verified.

CEMCO - 4000, ...2-Head Wide Belt Sander38" Width cap. - Drum, Platen configuration.Head Configuration:1st Head: 40 HP -1,780 RPM rubber contact drum head.2nd Head: 30 HP - 1,775 RPM platen style head.Specifications: -- 3 HP 230/460/60/3 Feed motor with TOSHIBA VFD controls. -- 15 - 60 FPM Conveyor feed speed . -- 30 HP - 3,525 RPM Vacuum blower. -- Vacuum type rubber conveyor feed belt. -- Push button controls and amp meters. -- Electric ProScale digital thickness readout. -- YASKAWA Varispeed F7.Equipped with & Features: -- VFD abrasive belt drive system. -- Outfeed workpiece dust cleaning enclosure.Includes: Replacement abrasive belts and belt racks.

(14) spindles with 1-1/2 hp motors on each. On/off switch for each motor. chucks adjust to grip up to 1/2” bit stroke adjustable from 4” to 10” 121” x 39-1/2” table with (4) hold downs Adjustable speed hydraulic feed 230 volt 3 phase

- Width capacity 53”. Drum, Drum, Combination Head (see sander specs - Head 1: Rubber covered contact roll, 10” dia, 65 shore adjustable with dial - Head 2: Rubber covered contact roll, 10” dia, 65 shore adjustable w/dial - Head 3: Combination head, (2) 5-1/2” finishing drums w/platen - 440 V, 60 cy, 3 Phase - Year 2000, Good Condition - Warehoused after plant shut down factory in 2013 - Have manuals /spec sheets - Machine weighs app 6000#’s. - Buyer must pay for riggers to load onto truck. (our forklifts can’t pick it up)

CEMCO MBV 54 Vertical Boring Machine54" x 15" Cast iron table with wooden top,Equipped With:(2) Universal spindles with movable spindle supports,(3) 2 HP - 1,725 RPM direct drive spindle motors,36" Stationary table height; 6" Max. vertical stroke, spindles advance hydraulically at 0 - 30 strokes/Min;Foot pedal actuated w/single cycle & continuous automatic modes;2 HP hydraulic feed pump, 12-gal. hydraulic pump system;Note: Riggers are required for loading

CEMCO 3 Head Industrial Sander. Running when removed from location.

CENTAURO T5E -1600 Semi-Automatic Hydraulic Copy Lathe with two copier heads. -- General data: 63" (1600 mm) Max. between centers and 8-5/16" height of center over the bed, 5.5 HP main motor with saddle advance using a lead screw with precision recirculating balls for max. accuracy.Automatic work cycle sequencing with electronic control capable of up to (5) different programmable cycles. -- Drives/Controller: Programmable saddle with variable feed speed; 900 - 1,500 - 1,800 - 2,250 - 3,000 & 4,500 RPM spindle speeds; 1.5 HP hydraulic variable speed carriage, 0 - 39-1/2 FPM, carriage return speed 39-1/2 FPM. CENTAURO "EM-12" Programmable Controller. -- Equipped with: (2) Hydraulic tracing units and revolving steady rest attachment; 3-1/2" max. square part size with revolving steady rest, 5" dia. max. with copying unit, 5.8" stroke of copying unit. 19-5/8" max. length for manual turning. -- 9.8" (250mm) Max copy dia., 6.8" (175 mm) Max. square section without steady rest.. -- Includes: Drive center, revolving tailstock center with 12 mm dia. tip, and automatic double pass system for finishing center. -- Note this machine has no top Back Knife for plunging with form tool. -- Machine manual included.

CENTAURO T5-1600 Hydraulic Copy Lathe with (2) back knives; Specifications: -- 63" (1,600 mm) Max. between centers, 4/5.5 HP main motor, two speed selector switch, 900 - 1,500 - 1,800 - 2,250 - 3,000 and 4,500 RPM spindle speeds. -- 1 HP Hydraulic power pack for variable speed carriage 0 - 19 FPM carriage; return speed 24 FPM, hydraulic tailstock with Pressure Reducing Valve (PRV) for fine control of pressure, especially helpful for small and/or slender turnings. Equipped with: -- (2) Independent copying units, (1) for roughing and (1) for finish cutting. 1st, 2nd pass & auto feature with 2nd pass active it will cut the pattern 2 times automatically and sequence the tools between cuts. -- Revolving steady rest, max. dia. 140/100 mm square ( 5.5"/3.9"), and for max. dia. 90/65 mm max. square billet size. -- 9.8" (250mm) Max copy dia., 6.8" (175 mm) Max. square section without steady rest.. Includes: -- (2) Back slides manually operated with knives for making dowel ends; 45/26 mm drive center for headstock and 12 mm center for tailstock, (2) V-type gouges with 0.6 & 3.5 mm cut radii.NOTE: Ex-Factory handles import/export to just about any country in the world.

CENTAURO T5E -1600 Semi-Automatic Hydraulic Copy Lathe with (2) Copier Heads. -- General data: 63" (1600 mm) Max. between centers and 8-5/16" height of center over the bed, 5.5 HP main motor with saddle advance using a lead screw with precision recirculating balls for max. accuracy.Automatic work cycle sequencing with electronic control capable of up to (5) different programmable cycles. -- Drives/Controller: Programmable saddle with variable feed speed; 900 - 1,500 - 1,800 - 2,250 - 3,000 & 4,500 RPM spindle speeds; 1.5 HP hydraulic variable speed carriage, 0 - 39-1/2 FPM, carriage return speed 39-1/2 FPM. CENTAURO "EM-12" Programmable Controller. -- Equipped with: (2) Hydraulic tracing units and attachment for revolving steady rest; 3-1/2" max. square part size with revolving steady rest, 5" max. with copying unit, 5.8" stroke of copying unit. -- Capacity: 19-5/8" Max. length for manual turning. 9.8" (250 mm) Max copy dia., 6.8" (175 mm) max. square section without steady rest. -- Includes: Drive center with, revolving tailstock center with 12 mm dia. tip, and automatic double pass system for finishing center.Note this machine has no top Back Knife for plunging with a form tool.

CENTAURO TC-1200 Copy Lathe;47-1/4" Max. between centers. -- 4-3/4" Height of centers over bed. -- Max. copy dia. 6" (4-1/8"). -- Max. dia. permitted by traveling steady 3-1/2" (2-1/2"). -- 4 HP main motor, 900 - 1,500 - 2,200 & 3,540 RPM spindle speeds. -- 1 HP hydraulic variable speed carriage with tool post and revolving steady rest. -- (2) Independent gouges working in conjunction with the traveling steady rest. -- Variable speed hydraulic saddle movement. Standard Equipment & Specs: -- Drive center with (2) interchangeable heads 1" and 1-3/4". -- Tailstock revolving center 1/2". -- Traveling steady rest max. 3-1/2" (square 2-1/2" x 2-1/2") with reduction bushing. -- (2) Vertical Tantung gouges, radius 1.2 mm and (1) precutting tool. -- Work-piece centering device. -- Tool support rest for hand turning. -- (2) Dust extraction ports 4" dia. -- Motor protection switch. -- Emergency push button. -- Front sliding safety guard. -- Standard: Service tool kit and Abrasive stone for cutting edge dressing.

Extremely well-built Edge Sander with 5 HP - 1,200 RPM TEFC Motor. -- (2) 11" x 60" Cast iron platens. -- 10" x 172" Abrasive belt size. -- 0.5 HP oscillation motor to produce (150) oscillations/Min with 1/2" movement. -- (2) 11-1/2" x 62" Cast iron side tables and (1) cast iron end table. -- All tables with 30° tilt up & 45° down. -- 5" Vertical table travel, 5" lateral side table travel and 4-1/2" lateral end table travel. -- Convenient hand wheel adjustment. -- Large 10" dia. x 10-1/2" face direct drive pulley with 4-1/2" dia. x 10-1/2" idle pulley for a huge sanding surface. -- Magnetic controls with overload protection & dust hood with 4" dia. outlet.

CHIA LUNG KR-30 2-Spindle Dual Table Automatic Rotary Copy ShaperEquipped with: -- (2) 19"; Dia. x 35-1/2"; H Tables. -- (2) 6-1/4"; Dia. Center clamp plates.

COE 249D Veneer Lathe with the following: -- 27" maximum log diameter, 110" knife length. -- 1484 Veneer Lathe Big Bar. -- 1390 Veneer Lathe Core drive. -- 3 to 1 inner drive ratio. -- Capable of peeling 35 cubic meters per hour. -- This COE Veneer lathe line was completely rebuilt and installed in 2006. The lathe was operated less than one year and is reportedly in excellent condition.

COE 4 Ft. Veneer Peeling Line with the following major components and features: -- Log cut-off saw. -- Geometric lathe charger. -- Dual spindle 4' COE Model 263 Lathe: &#9679 Diameter of outer spindle 7" &#9679 Diameter of inner spindle 4" &#9679 Max. swing 48" &#9679 Knife length 56" &#9679 Lloyd controls including motor starters &#9679 Main drive DC-AC 165 HP/200 HP -- Veneer conveyor to clipper. -- Pneumatic Clipper.ALSO AVAILABLE: VENTEK Veneer Scanner (no computer included).NOTE: Veneer stackers not included.

COMEC - FAS/2, ...Corner Milling MachineCOMEC FAS is a dedicated milling machine with: Inclinable heads for machining the corner of chair seats. Specifications: -- (2) Heads with: 5.5 HP motor and 40 mm spindle shaft. -- Max. cutter size: 150 mm (5.9"). -- Tilting of milling units: 20°/ +45° in horizontal plane. -- Fixed left hand column to support head unit. -- Max. working height: 200 mm (7.8").

COMEC - LON-LS, ...Horizontal Belt SanderSpecial design for sanding of straight or curved solid wood parts such as: Chair legs, chair backs and other similar & difficult-to-sand parts.10 HP Belt driven motor; 12" dia. contact drum for 10" wide x approx. 140" long abrasive belt; air tracking & belt tensioning. -- Stock is fed over the contact drum with an overhead variable speed, pneumatically tensioned feed wheel. -- Sander belt power: 6.6 kW (9 HP approx.) - 220/440 V, 60-Cy, 3-Ph motor.

COMEVA - CUBE 3, ...Edgebander (Single Phase)The CUBE 3 from COMEVA is designed to be a very compact "every day" Edgebander. The CUBE 3 Edgebander is operated through a PLC control system with a touchscreen. The machine handles panel thicknesses of 0.315" up to 1.77" (8 mm to 45 mm), The coil feed accepts Edgebanding from 0.4 mm to 2 mm thick; strip material can be hand-fed.Equipped with: -- Heated infeed fence for optimum glue penetration. Large capacity Teflon coated glue pot (2.64 Lbs). -- Single motor End Trimming station -- Top & Bottom Trimming -- Top and bottom Buffing. -- Feed speed is variable between 9.8 & 23 FPM (3 - 7 MPM); feed chain pads with replaceable rubberized surface inserts. -- Rubberized holddown rollers with ball bearings for low friction and long life. Work stations: -- Pneumatically operated guillotine for up to 2 mm thick banding, followed by spring loaded double pressure rollers. -- Single front/rear trimming unit, 0.3 HP motor. -- Top & Bottom trimming units, (2) 0.5 HP motors. -- Top & Bottom buffing station, (2) 0.16 HP motors. -- Complete with: Safety enclosure protects the operator from noise and debris. Engineered & Manufactured by COMEVA S.L, in Spain.Includes: Owner’s Manual with mechanical & electrical schematics and parts breakdown; covered by a 1-Year Factory Warranty on parts.

CONCEPTION CRP-180 Short Block Feeder Infeed ConveyorSpecifications: -- About 4 m long X 1.2 m wide, 2-ply rubber belt, friction back with Photocell for automatic operation -- Short Block Feeder; Blocks to be 25mm longer than width -- 14' rotating carousel with adjustable speed via VFD with Motorized wheel to avoid blockage -- Exit opening adjustable to the block width -- 200 mm x 7m long belt conveyor to carry the blocks to index rolls; Servo indexer controlling the flow powered by an electric motor; Speed-up belt powered by an electric motor -- Wane System: Scanner to detect wane integrated in conveyor -- Display screen to show wane detected; Kicker to kick blocks that are not in good orientation -- Conveyor to return it into the spreader belt conveyor -- Automatic Operations

CONQUEST 1-23H CONSTRUCTION / LINE BORERUSA-Made 46-spindle Horizontal/Vertical Boring Machine.Specifications: -- (2) 2 HP BALDOR Motor to drive a helical gear head with spindles on 32 mm centers. One head with (23) Spindles in the vertical plane and One head with (23) spindles in the horizontal plane. -- Pneumatic head movement to reduce operator fatigue. -- 20-1/2" x 36" Cast iron front table.Complete with: -- 98" Back fence with repeat stops. -- (2) Pneumatically operated index pins & (2) pneumatically operated holddowns. -- Collets that accept 10 mm shank bits. -- Bit requirements of 10 mm shank. -- Foot pedal control....$150.00 crate charge.

CONQUEST 1-23H Horizontal 32 mm Boring Machine;Specifications: (1) 23-Spindle horizontal boring head, 2 HP "BALDOR" motor, helical gear driven spindles spaced on 32 mm centers, 3,450 RPM; cast table. -- Equipped with: Pneumatic head activation, side fences. -- Complete with: (2) Pneumatically activated holddowns and foot pedal. NOTE: This unit has 2 sets of arms. All the screws have been replaced for the drill bits. Ready to go to work!