Woodworking Equipment For Sale

West Salem model 2420GR1-H wood grinder/hog 480 v Bottom discharge No screen - machine has breaking bars Disconnected and ready to ship

WESTERN PNEUMATICS HEAVY DUTY FINGER JOINTER WITH THE FOLLOWING EQUIPMENT & FEATURES: -- Right & Left Shaper Section: Thickness Capacity: 3/4" - 2" maximum; Width Capacity: 1-1/2" - 8" maximum; Length Capacity: 5" min. - 36" maximum; -- (2) Scoring Saws with 7-1/2 HP - 3,600 RPM motors; -- (2) Trim Saws with 7-1/2 HP - 3,600 RPM motors; -- (2) Shaper Spindles are hydraulically powered; direct driven @ 3,600 RPM by -- (1) 60 HP Hydraulic Power Unit with (1) cartridge unit per spindle. Hydraulic conversion was performed during the first year of operation. -- Western's 2-1/2" wide feed chain with lugs on 9" centers; 15 HP variable speed drive with up to 120-lug per min feed speeds; with angle transfer conveyor, air bag pressure head with quick-change feature & brush hold-downs -- APQUIP Extrusion Type Glue Applicator complete with mixing system. Currently arranged for 3/8 finger joints including (4) 3/8" glue combs -- Manual Corner Transfer to the assembly section. (allows for inspection and rejection of blocks for poor joint quality, missing proper glue spread, etc. prior to going into assembled boards) -- 12' Pre-Assembly Infeed Conveyor with feed speed ramp up/down; with side alignment rolls and dual top and bottom pre-assembly rolls -- Flying Cutoff Saw operating from below -- Assembly Press: 20' board capacity with hydraulically powered press -- Automatic Cycling Assembly Section: Feed speed varies automatically from 50 to 200 FPM, depending on incoming block lengths. Boards advance through the Cutoff Saw to a moveable limit switch where they are cut to length with a bottom-mounted 7-1/2 HP Flying Cutoff Saw arranged for continuous non-stop assembly. The cut to length board drops down into the squeeze chamber while the next board feeds out and above the preceding board where it is cut to length. Pressed lengths are pushed out onto material outfeed arms by the following board

//This machine is in an Auction on exfactoryauctions.com// //Link to machine: http://exf.ac/i61 WHIRLWIND 1000 L Upcut Saw Specifications: 2-3/16" x 8-1/4" Cap., 14" blade cap., 3,450 RPM, left-hand unit feeding from right-to-left, 5 HP BALDOR motor. Complete with: (5 - 90) Cycles/Min; magnetic starter with low voltage controls, air filter, regulator, coalescing filter, and 4" dust chute. NOTE: The above specs are taken from literature and considered accurate. As always please take advantage of the inspection period to verify. Items seen in the background are NOT a part of this Lot.

WHIRLWIND - 855, ...Dual Table Oscillating Edge SanderDouble-sided with: 8" x 56" Platens size.Specifications -- 7-1/2 HP - 1,725 RPM TEFC Motor; abrasive belt size: 8" x 151"; approx. (150) oscillations/Min with 3/8" stroke. -- 11" x 55" Side table; tilts 0° - 45° with 8" vertical adjustment; tiltable end table; iron frame machine base. Complete with: -- Magnetic electrical controls w/overload protection; dust hood on drive end; all standard equipment.

Whirlwind Undercut Saw with Tiger Stop Fence

Whitney 105 Planer 24" Planer Used daily in current shop.

Williams 125 CJS1 Hammermill

Williams 125 HP Hammermill 230/460 3-phase

William & Hussey "W-7S" Moulding Shaper -- Specifications: 17-1/4"x 14" Table size, 2 HP main motor, 2-knife cutter head, 3,450 RPM spindle speed, 7" max. cutting height, 1/4" min. thickness 3/4" deep max cut.. Max moulding cap. 7" wide, max. planning cap. 7" wide. -- Complete with: Dust hood outlet, electrical disconnect, and mounted on fabricated steel stand w/casters, Multi-pass

100 HP 230/460 volt 20” x 19” inlet 9” x 28” outlet no hopper

WILTON 4421-2 20" Pedestal-Type Disc SanderSpecifications: -- Table size 10-1/2" x 27-1/2", Table tilt 45° Out/30° In, Table can be lowered below disc to accommodate large workpieces.Equipped with: -- 3 HP 1,720 RPM Direct drive motor, Low voltage protection switch. -- Positive lock rack & gear table tilt.

WILTON 4421-2 DISC SANDER ---Price Negotiable---Make an Offer!--- Heavy Duty for Wood, Metal, Fiberglass, or Plastic! - Pedestal-Type Disc Sander - Table size 10-1/2" x 27-1/2", Table tilt 45° Out/30° In, Table can be lowered below disc to accommodate large workpieces - 3 HP 1,720 RPM Direct drive motor, Low voltage protection switch - Positive lock rack & gear table tilt

Wintersteiger DSG Sonic Frame Saw

Wisconsin B20-M multiple spindle horizontal drilling machine 8' 4-HEAD 13-SPINDLE DRILLING MACHINE 3 HP DRILLING MOTORS, HYDRAULIC , AIR CLAMP Serial # B20M-6825-96 5 HP hydraulic pump: 230/460V, model CLT-30 GAL, 1050 psi, 8 GPM., serial# 1-89175-0 Four Baldor Drilling motors 3 HP, 208-230/460 volts, 3450 RPM., Baldor, Removed from a complete plant liquidation in October 2020. Stored inside a climate controlled room, Contact us for a delivered price

MLS Number 10684323 Wisconsin Automated Machine C-450 Tennoner Single end tennoner Automatic double head coping tennoner Model C-450 Serial: C-450-6901-00 230 volts, 3 phase, 60 Hz. Allen-Bradley and Motortronics electrical Motors are 230 volts 48 full load amps. 15.2 amps on largest motor

32" Vertical grinder with 25 HP motor Dentom 624 9500 BTU Furnace automated measured feed controlled by furnace temperature Holding tank for feed from the grinder which is automatically fed to the furnace...that feed is temperature controlled.

Woods 502M hardwood flooring machine

WOODS Planer-Matcher - Model 412 motorized, heavy duty planer-matcher with 6 heads. Ideal machine for surfacing dimension lumber or specialty products such as siding and flooring. 6" x 14" capacity, 8 knife heads; 50 hp top, 25 hp bottom, 20 hp sides; 20 hp bottom profile, 15 hp top profile. Item 32203.

Woodtech QSG 650-R-RPA 24" Widebelt (2) Heads24" width cap, Drum, Combination HeadHead configuration1st Head: Contact roll2Nd Head: Combination head (Roller and Pad)Specifications -- 24" Widebelt Service Side: Left -- Working Thickness: 3-150mm -- Minimum Working Length: 460mm -- Feed Speed: 0-19m/miMachine Frame -- Built with rectangular profiled steel beams to give a very high rigidity to the frame;Main motors positioned inside the frame in a protected position -- Machine frame is connected by high strength hardware (8.8G), and welded for maximum rigidityEquipped with & Features -- V-belt drive from main motors to sanding heads, -- Disk brakes on each sanding drum for emergency stopFeed System -- Feed table is made of steel with a surface tolerance within 0.05mm; table polished to avoid wear of the internal side of the feed belt -- Table is heat treated for accuracy and durability -- Feed speed variable in continuous from 0-19m/minNote : Extra BeltsWoodtech Model QSG 650-R-RPA 24" Widebelt

1994 Woodtech Bandsaw Model 816420