Woodworking Equipment For Sale

NorthTech 18" Pop-Up Saw. 10hp Motor. #00872

Northtech Chop Saw

Northtech Machine NT-GRS-300RF Gang Rip Saw REDUCED Roller feed Max depth of cut is 4". Max width is 12". New Saw Blades And Spacers

Northteck MRS-14-DXL 460v Manufacturer notes: This is a very popular machine and cost effective. New open ended design allows for you to cut wide material up to 27-1/8? wide. Plus spare arbors, lasers, and the optional quick locking, easy to adjust infeed will not break the bank. The Northtech heavy-duty 50 HP multi-rip (“gang-rip”) saw with 15? maximum blade diameter quickly and accurately cuts material up to 4-15/16? thick and 27-1/8” wide. Cutting both sides of your blanks at once provides incredible parallelism, reducing required moulder allowance, and increasing your yield. Laser guides (one included) and an optional 103” fence make proper alignment of even the longest material simple and precise. Variable feed speeds of 25 – 120 FPM and powered height adjustment further improve operator efficiency.

Northtech MRS-12N Gang Rip 50 HP Motor Needs a new safety with on the door

Northtech NT 16R-10 Tilting Arbor Table Saw Infeed Roller 10 HP Motor

6” width capacity 8” thickness capacity 30 hp main motor, 1.4 hp feed motor 3 hp blower motor…460 volt 3 phase 559 rpm blade speed digital oiling

NOVY 1872V Multi Spindle Vertical Boring Machine 12 Spindles Vertical boring machineSpecifications: -- Table Hardwood 18" X 72' -- Table stroke 0"- 6" -- (12) Spindles in line at 5" center to center, spindle nose with 0" to 1/2" chuck -- (2) drive motor 2 HP with magnetic starter -- (4) Spring loaded hold down -- Savety guard -- Foot swtich

Oakley Edge Sander

OAKLEY H-5 Double Sided Edge Sander. -- General Specs: With 7.5 HP -1,800 RPM TEFC motor; (2) 8-1/2" x 57-1/2" Cast Iron platens; 8" x 164" abrasive belt, 4,680 FPM belt speed. -- Equipped with: One 11" x 62" Cast iron side table on one side and (1) 19" x 64" cast table on the other side, (1) cast iron radius tilting end table, end table tilts 0 ° - 45°; 6" vertical table travel w/hand wheel adjustment. -- Features: Rubber covered direct drive pulley and idler pulley,Complete with: Magnetic starter with overload protection, (8) dead head radius ends with graphite covering, and (1) steel covered spare head roll.

OGAM PO/M Straight Line Rip Saw;Specifications: -- 20 HP Main motor. -- 24"; throat capacity. -- Max. cutting height: with 12" blade 3", with 16" blade 4". -- Min. diameter of circular saw blades: 8". -- Max. dia. of circular saw blades: 16". -- Min. length of working pieces: 10". -- Variable feed speed from 50 -154 Ft./minute. -- Feeding belt width: 11". -- Spindle Speed: 4,500 RPM. -- 36"; x 60"; table.Equipped with & Features: -- Fence and rail system with one stop. -- Infeed table row of anti-kick back fingers. -- Steel smooth top hold down roller. -- Top row of anti-kick back fingers. -- Steel smooth top hold down roller. -- Split hold down steel smooth roller around blade. -- Split hold down steel smooth roller around blade. -- Steel smooth top hold down roller. -- Chain is in excellent condition!

Ogden SL3660 RFS

OLIVER 4045 12" PROFESSIONAL TABLE SAW, with 36" FenceHeavy-duty cast iron table precision ground for accuracy; rugged machine frame construction provides maximum stability and reduced vibration.Specifications: -- 12" Blade capacity and 0° - 45° tilting arbor with digital read-out. -- 7.5 HP Motor at 3,450 RPM. -- Complete with: 52" rip fence capacity that will handle most of your work. -- 48" x 52" Cast iron table. -- Blade guard, miter gauge, push-button controls. -- Parts list & operation manual.

OLIVER 4016 10" Table Saw, 5 HP, 3-Ph w/36" Rail Specifications: -- 5 HP motor; poly V-belt drive system with belts that run smoother and with less vibration, giving you the highest quality cut available. -- Top it all off with with OLIVER'S Optimus square tube fence and a digital blade angle readout system and you've got a saw that tears it up with accuracy and in style! -- Model 4016.004 5 HP, 220V. 3-Phase.

14" Max. blade cap., 2 HP motor, 1" dia. arbor tilts 0° - 45° via hand wheel; separate handwheel for raise and lower of the arbor. -- Includes: original miter gauge, counterweighted overhead blade guard, wrench. -- NOTE: Table and Biesemeyer Fence shown in photos have been sold and are not included with machine.

OLIVER 2019 Wood Turning Lathe;This lathe brings the lathe back to the OLIVER line, in true OLIVER Fashion! -- Starting with a solid, stable cast iron base, legs, bed, tool rest, and headstock. -- OLIVER adds a powerful reversible 2 HP motor with a wide speed range for a variety of tasks. -- A frequency inverter and RPM Digital Readout give you an accurate read on your speed so you can precisely adjust for any particular job.Specifications: -- 41" Between Centers, 18" Swing over bed, 40" Swing Outboard; -- Spindle Speed 200 - 2,400 RPM, Front Faceplates 6". (2).Features: -- One of the best features on the lathe is the In-board and Out-board headstocks (slides on the bed), enabling you to work on very large Bowls and most anything else you need to turn. The slide extension can increase the center distance to 57" with optional extension bed.Includes: -- Integral spindle index for (36) positions.Dimesniosn/Weight: 46.5"long x 19.5" depth x 49.25" height. Approx. 415Lbs.Available Options: -- Bed extension that mounts in two positions....Protective Safety Guard. Assembly.... Please call. -- See attached literature for more specifications.

20’ OLIVER LATHE – PATTERN MAKERS TURNING LATHESpecifications: -- 30" Swing over 20’ bed, 15"; clear from bed to center; 92" Swing outboard, 16’ between centers -- Belt-drive Step pulley, 4-Speed Step pulley -- Single geared tool rest to hand crank for traversing the length of lathe -- Head Stock Spindle dia. 1 – 7/8";, Tail Stock Spindle dia. -- Head Stock can be offset 10 degrees for tapered columns -- Cone dia. Steps – 5";, 7 – 3/8";, 9 – 5/8";, 12"; -- (8) Spindle speeds, 160 to 2,520 RPM

Oliver bandsaw circle cutter, 36" wheels, stored inside

OLIVER - 34-DD, ...Disc Sander (Double)(2) 30" Dia. steel discs; 5 HP double shafted motor turns @ 1,050 RPM.(2) Steel side tables, 40" x 15", (1) slotted and (1) plain; both tables tilt 10° up and 45° down.(1) Table with 6" manual vertical adjustment; rack travel adjustment by screw & crank. -- Complete with: Magnetic controls; (2) dust outlets; large handwheels for easy adjustments.

OLIVER 6910 Oscillating Spindle SanderPedestal style Spindle Sander constructed for rugged use .Specifications: -- 2 HP Motor drives and is connected through a flexible coupling, and can be installed or removed without disturbing the drive mechanism. -- Spindle speed 1,725 RPM, Oscillation speed 75 Cy/Min with 1-1/2" stroke length. -- Spindle quill runs in precision ball bearings, oscillated by a heavy duty worm & gear mechanism running in a bath of oil. -- (10) Spindle sizes provided: 1/4 x 5", 3/8 x 6", 1/2 x 6", 5/8 x 6", 3/4 x 9", 1 x 9", 1 1/2 x 9", 2 x 9", 3 x 9" and 4 x 9"; 100 grit abrasive sanding sleeve with each spindle. -- Large 24" x 24" precision ground cast iron table mounted on large trunnions that can be tilted 45° down and 30° up by use of a convenient handwheel. -- Complete with: Pedestal style stand.