Woodworking Equipment For Sale

POWERMATIC MODEL 100 PLANER12" Cap., 5 HP 5,300 RPM belt driven main motor, 1/16" to 5" thickness opening, 3-1/8" dia. 3-knife cutterhead with high speed steel knives, 18 FPM fixed feed speed with in-out clutch -- Corregated infeed rolls; 12" x 24" precision ground cast iron table. 1/4" max. depth of cut, 7-1/2" min. stock length (unbutted). -- Complete with: Knife grinder, Magnetic controls, cutterhead guard with dust chute on enclosed steel stand.

POWERMATIC 221 PLANER WITH BYRD HELICAL HEAD20" x 8" Cap., 10 HP TEFC belted drive motor, BYRD Helical cutterhead, hand wheel micro-adjust table; 1 HP feed motor for variable speed from 20 - 50 FPM, segmented infeed roll and sectional chipbreaker, 4" dia. smooth outfeed roll. -- Complete with: Magnetic starter and dust hood.

10 HP. 4"x 10" cutting capacity. Upcut and top shield operated by air w/ foot peddle control. Top table size 25"x 27" Good working condition. Call for info 918-752-8142

POWERMATIC KUFO 1632 (KUFO SK-15A) Wide-Belt SanderSpecifications: -- Open-sided single head 16" Wide Belt Sander. -- Open-sided design to allow up to 32" wide workpiece in (2) passes. -- Combination head with a 4" diameter rubberized contact drum. -- Head with a finishing platen. -- 5 HP Single-phase or 7.5 HP 3-phase motor. -- Air abrasive belt tracking. -- Manual readout to reference the 0" - 6" thickness setting. -- Center jack to set bed location. -- 0.25 HP Conveyor drive with 20 FPM. -- (2) Infeed & (2) outfeed spring loaded holddown rollers. -- Side extension support, load meter and safety shutoff. -- Operators manual.

Powermatic TS 80 Shaper Call 800-459-2148 for more info.

POWERMATIC - 28, ...Shaper1-1/4" Dia. spindle; 7-1/2 HP - 3,600 RPM motor; 3,300 - 9,500 RPM spindle speeds via Factory installed Variable Frequency Drive.4-3/4" Cap. under nut when using the 1-1/4" spindle; spindle brake; 30" x 39" table.

TABLE SAW TOP MEASURES 44" WIDE X 76 ½" LONG TABLE HEIGHT FROM FLOOR 34% " COMES WITH 5 - 12" DADO BLADES 1 HORSE POWER POWERMATIC MATERIAL FEEDER 5 HORSE POWER SAW ARBOR MOTOR 440 VOLT 3 PHASE

POWERMATIC - RB-37, ...Single Head Wide Belt Sander1-Head, 36" width cap., combination sanding head. -- Includes: 4" Dia. contact roll & 2" wide polishing platen, micro-adjust platen; 15 HP main motor. -- Abrasive belt size: 37" x 60"; with air tensioning, air jet abrasive belt tracking.1 HP Feed drive; variable feed speed of 15 - 30 FPM conveyor speed.0" - 5-1/4" Opening with: (4) Screw jacks; double infeed & outfeed rubber covered holddown rolls. -- Complete with: Magnetic starter; overload protection; load meter; emergency brake.

POWERMATIC - 26, ...Single Spindle Shaper -- Specifications: 5 HP (3.7 kW) - 3,600 RPM Belt drive motor; 7,000 & 10,000 RPM spindle speeds via 2-speed step pulley; reversing switch. -- 1" Dia. solid interchangeable spindle featuring 3-7/8" cap. under the nut; 3" spindle travel w/handwheel adjustment -- Complete with:24" x 26" Cast iron table; miter slot; 7" insert opening; adjustable fence; magnetic controls. -- Actual Model is: POWERMATIC 26

Producto Gothic Fence & Post Picket Machine. Out and Ready to ship. Producto is now Global Marketing Group.

PROFILEMATIC 503 PROFILE SANDER3-Head feed through, sands from top at adjustable angles narrow moulding type parts as well profiled edges on panels.Equipped with: -- (3) Top VPS vibrating air-loaded sanding units, 0.5 HP vibrating motor ea., sanding heads have (2) pneumatic cylinders for sanding pressure control and oscillate with 1/2" stroke on dust-protected round guides, variable vibration speed from 200 - 1,800 RPM; adjustment range of 120ø to conform to profile, equipped with air shower to clean workpiece & sandpaper automatically. -- Part transport is achieved by a 4-1/2" wide linatex coated conveyor belt system, "quick adjustment" holddown wheels & fence system, variable feed speed 0 - 35 FPM powered by a 0.25 HP DC gear drive (forward & reverse feed mode). -- Each sanding head with its own controls for manual raise & lower, pressure control and vibrating speed. Profile width approx. 1/2" min. to 4" max., material feed through thickness up to 5"; support fences for up to 10" moulding width.

Make an offer - Machine is in an Ex-Factory Liquidation. 4-Station Profile Shaper Specifications: 6" Chain drive with non-marking rubber top pads traveling on a hardened and ground precision dia. 5/8" round rods, Top pressure beam driven, Heavy duty fabricated transporter frame, Forward and reverse mode and block mode for creating sanding tools Precision X & Y axis mounting stands, 60° rotating tilt on mounting stands with positive lock, Independent activation control at each station, Adjustable infeed fence system, All dust hoods and guards, 2 HP AC variable speed gear drive 5 to 60' per min. Workstation 1: 3.5 HP TEFC Saw Arbor Motor, 1" Dia. Spindle, Dust Hoods with 4" outlet, Mounted on precision X & Y slides Workstation 2 & 3 - Belt Sanding Unit: 2 HP AC motor drive, Air belt tension system, Independent belt tracking system, Air activated sanding pad with touch control, 2" sanding belt width, Guards and Dust hoods with 4" outlet Workstation 4 - Wheel Sanding Unit: 3" HP variable speed (0-3,400 RPM) AC TEFC drive motor, 1" or 1.25" arbor 3.5" long, Dust Hood with 4" dia. outlet, Mounted on precision X & Y slides SPECIAL NOTE: Needs New PLC or wire for traditional controls NOTE: Above specs are taken from literature and thought to be accurate. As always please take advantage of the inspection period to verify. Items seen in the background are NOT a part of this Lot.

2 HP motor,220V, 3 PH, 60 HZ -- V-belt drive, Allen Bradley push button overload control. -- Seller recommends replacing rubbers & covers.

Progressive Systems Inc End Matcher

PROSAND HF-412 Curved Part Belt SanderBelt oscillates up and down.÷Feed wheel removable.

PUTSCH EBP 950PMCR EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): Specifications: -- Edge material thickness 0.4 - 3 mm coil & up to 5 mm strips.Min./max. panel thickness "all units" 8 - 50 mm (0.39" - 1.97"). Max. material thickness when using CR unit is 1.77" (45 mm). Min. panel width: 95 mm (3.7") & 110 mm (4.3") min. length.Fixed feed speed of 9 MPM (29.5 FPM).Equipped with: -- Automatic coil feed magazine with an oscillatory cutting shear for uninterrupted edge feed. -- Gluing Unit: Teflon coated glue tank, approx. 10-minute heat-up time. -- Side Pressure Unit: 3-roll pressure unit w/1st roller power driven via clutch with pneumatic in & out positioning, (2) idler rollers.Workstations: -- Pre-Milling Unit: (2) 2.0 HP (1.5 kW) motors with (2) opposing 60 mm diamond cutters that are micro-adjustable to mill up to 2 mm from the panel edge for optimal, chip-free glue application. -- End Trimming Unit:(1) 0.3 HP (0.2 kW) - 12,000 RPM Motor, automatic single motor end trim unit with (2) 80 mm blades. -- Top & Bottom Trimming Unit: (2) 0.5 HP (0.37 kW) - 12,000 RPM ea. Motor with 75 mm cutters (with disposable knives) that offer a straight 2 mm radius / 15° bevel.The flush trim unit also includes 120 mm scratch-resistant vertical disc copiers that are ideal for delicate finishes. -- Corner Rounding Unit: NOTE: When using CR unit, the max. material thickness is 1.77" (45 mm) & min. panel length is 7.78" (200 mm).(1) 0.3 HP (0.2 kW) - 12,000 RPM Single motor Corner Rounding unit for leading & trailing edges. The corner rounding unit is fixed to the frame crossbeam on double linear guides and features 50 mm cutter blocks, as well as vertical/horizontal 50 mm diameter copiers for profiling straight, curved, and beveled edges. -- Edge Scraping Unit: Top & Bottom PVC Scraper for up to 3 mm radius, complete with 3 mm scrape shaving collection box. Programmable, pneumatic exclusion on/off. -- Buffing Unit:Top & bottom buffing unit (2 x 0.2 HP - 1,400 RPM motor each), tilting range 8°.Controller: "ETOUCH" Touch Screen Control for the "EBP 950" Series; the ETOUCH touch screen control is a 7-inch color programmable display.Operators can store up to (99) working programs and connect to an optional network to read statistical data, diagnostic messages and online updates.The Control permits the operator to engage or disable specific work operations, while also providing immediate access to diagnostic messages and statistical data such as hours of operation and length of coil used.Complete with:Track Drive Chain feed speed 9 MPM (29.5 FPM).(2) Rows of upper pressure wheels in holddown beam.Adjustable material support outrigger.Sound & Safety Hoods.Used Tooling -- Actual Model is PUTSCH EBP 950PMCR.

²QUICK 14-Section Pneumatic Clamp Carrier with 12-1/2' width capacity With (8) Standard zinc plated clamps per section (112) clamps total), 38" opening on clamps Standard Features include: Clamps jaws are 3-1/2" high x 4-3/4" wide with 1° inward draft to keep stock securely held down. Clamps use 3/4" dia. full-length screws; corrosion resistant, zinc plated, full box frame. For face gluing, Rocking Plates available as optional equipment Panel Flattener with easy to use controls.Pneumatic Clamp Tightener; 3,000 RPM air wrench is 5 to 10 times faster than competitive tighteners; two-handed, trigger activated tightener is more confidence inspiring than the old ergonomically awkward "swing-style" clamp tighteners. Fast tightening and full-length clamp screws eliminate need for manual adjustment of rear clamp jaws. Electric Motor Rotation; push button, automatic cycle with indexing. Automatic Rotation Cycle includes entire sequence; reverse rotation, front-rest out, forward rotation, front-rest in, and lay clamps on front rest. Perfectly! Every time! Complete with:Foot levelers, coiled air lines, flexible conduit for electric wires, automatic air line oiler, high quality urethane finish coating, and tool box with spare parts & tools. 14-Section Clamp will produce 300 panels

QUICK 40-Section Heavy Duty Clamp Carrier 12.5' with Auto Clamp Loosener -- With (9) Standard zinc plated clamps per section (320 clamps total), 32" opening on clamps.Standard Features include: -- Clamps jaws are 3-1/2" high x 4-3/4" wide with 1° inward draft to keep stock securely held down. Clamps use 3/4" dia. full-length screws; corrosion resistant, zinc plated, full box frame. For face gluing, Rocking Plates available as optional equipment -- (2) Hydraulic Semi Automatic Clamp Tightener/Panel Flattener; 3,000 RPM air wrench is 5 to 10 times faster than competitive tighteners; two-handed, trigger activated tightener is more confidence inspiring than the old ergonomically awkward "swing-style" clamp tighteners. Fast tightening and full-length clamp screws eliminate need for manual adjustment of rear clamp jaws. -- Hydraulic Upper Auto Clamp loosener for 12.5' wide -- Electric Motor Rotation; push button, automatic cycle with indexing. Automatic Rotation Cycle includes entire sequence; reverse rotation, front-rest out, forward rotation, front-rest in, and lay clamps on front rest. Perfectly! Every time!Complete with: -- Conveyorized glue spreader 20" wide with 10' infeed and 13' outfeed -- Foot levelers, coiled air lines, flexible conduit for electric wires, automatic air line oiler, high quality urethane finish coating, and tool box with spare parts & tools.

Quick Pneumatic Clamp Carrier with 20-sections and 12-1/2' width capacity. -- (8) Heavy Duty zinc plated clamps per section with 52" opening. -- Includes 160 clamps with 52" openings and 3.5" high x 4-3/4" wide jaws with 1° inward draft. -- Pneumatic overhead panel flattener riding along with tightener -- Semi-Automatic Pneumatic clamp tightener . -- Single button automatic electric motor rotation cycle with indexing. -- Heavy Duty frame with 3" diameter shafts and 6" I-beam legs. -- Includes foot levelers, coiled air lines, flexible conduit for electric wires, automatic air line oiler, high quality urethane finish coating and tool box with spare parts & tools.

QUICK MACHINERY N-P80 Air Pod style Cold Press. -- Heavy Duty I-beam construction with machined steel plates for flat smooth pressing surface.Specifications: -- Platen pressing area size: 62" x 146" with end loading on 62" side. -- 80 PSI Platen pressure over the entire surface area with 105 PSI supply air pressure. Pressure is applied by (60) 12.8" dia. air pods with 5.9" stroke; -- Air powered raise and lower idler rollers in the bed of the press for loading & unloading panels; raising & lowering of conveyor by control button on panel. -- Motorized Adjustable Daylight Opening from 2" to 40"; push button controls operate an electrically powered chain driven worm gear drive system for precise positioning of upper platen setting/opening. -- Controls: 60-Min cycle timers provide visual and audible signals at the end of each cycle and automatically releases platen air pressure at the end of each cycle if desired. -- Single platen 62" X 146". (2) Air pressure zones for upper platen: (4' x 8' and 5' x 12') -- Optional powered roller tracks for an additional fee. -- The press model shown in pictures is a dual platen powered feed through end load press. -- Actual model is N-P80-05-12-EL-1PL-M-40-2Z