Woodworking Equipment For Sale

Cantek Double Surface Helical Planer

CANTEK RAPIDEDGE PRO EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Specifications:0.4 - 3 mm Edge thickness; strip material can be hand fed; panel thickness 0.315" - 1.77" (8 - 45 mm); min. panel length 6.7" (170 mm); min. panel width 3.54" (90 mm). 0.4 kW Heated infeed fence for better glue adhesion; 2 HP (1.5 kW) feed motor with fixed feed speed of 29 FPM (9 MPM).Equipped with: -- Pre-mill Unit:(2) 2 HP (1.5 kW) - 12,000 RPM each counter rotating cutter-heads for removing up to 3 mm of the panel edge. -- Glue System:Quick-Change 1.2 kG Teflon coated glue pot is designed for EVA hot melt glue. The glue pot is a Quick-Change type and can be removed and replaced in less than (1) minute.Spring-loaded Pressure Unit with (2) pressure rollers.The Guillotine shear can rough trim coiled material up to 3 mm in thickness. Pressure rollers section consists of : (1) Large driven roller followed by a smaller one. Workstations: -- End Trim: (1) 0.29 HP (0.22 kW) - 12,000 RPM Single motor end trim system with (2) saw blades; unit is mounted on high precision linear guide rails. -- Rapid Top & Bottom Trim:The RAPID adjustment system uses a pneumatic 3-position adjustment to quickly change from 0.5 mm to 1 mm, to 2 mm edgebanding. This is done directly from the Control Panel.(2) 0.5 HP (0.37 kW) - 12,000 RPM high frequency motors for Top & Bottom trimming of the panel; each motor has an inset knife cutter head that can be adjusted from flush to beveled finish for thin edges and radius trimming (2 mm radius). -- Nesting Function:Nesting kits are installed on the Top & Bottom trimmers and scraping units to ensure they properly trace the panel when predrilled for hinge holes. -- Corner Rounding:(1) 0.5 HP (0.37 kW) - 12,000 RPM, high frequency single motor Corner Rounding Unit. Quick change corner rounding motor for fast changeover from 1 mm to 2 mm radius on the ends.Unit can process between 0.4 - 3 mm and up to a board thickness of 1.77" (45 mm).The multifunctional cutter can round straight or radius edges with a 2 mm radius cutter. -- Profile Scrappers:Multi-radius scrapers allow operator to apply a 1 mm or 2 mm radius on the Top & Bottom of the panel. -- Flat Scrappers:Flat insert knives designed to remove any excess glue which remains on the surface of the panel after applying the edge due to squeeze out. -- Buffing Units:(2) 0.2 HP (0.12 kW) - 3,000 RPM motors, Top & Bottom Buffing units leave a super finish on ABS & PVC edging and removes any discoloration on the edges. -- Release Agent Spray Unit:Applies release agent to the Top & Bottom surface of the panel before applying the glue allows for simple removal of any excess glue.The unit is located before the Pre-milling Station so any overspray which gets on the edge will be milled off to ensure proper bonding. -- Cleaning Agent Spray Unit:The Cleaning Agent System sprays the Top & Bottom edge before the Buffing Unit & designed to polish the edge and loosen any excess glue residue on the surface

CANTEK - MX340M, ...EdgebanderThe "MX340" from CANTEK is designed to be a compact and durable Edgebander. -- Machine equipped with: End trimming; flush trimming; PVC scraping; buffing. -- The "MX340" Edgebander is operated through a PLC Control System with an LED display and keypad.Specifications: -- Handles panel thickness of 0.315" - 1.77" (8 mm to 45 mm); min. part length: 3-1/2"; min. part width: 3-1/2". -- Coil feed accepts edgebanding from 0.4 mm to 3 mm thick; strip material can be handfed. -- Conveyor feed speed: 23 FPM (fixed).Workstations: -- Heated infeed fence for optimum glue penetration; large capacity Teflon coated glue pot; 2.64 Lbs. -- Pneumatically operated guillotine for up to 3 mm thick banding; followed by spring-loaded double-pressure rollers. -- Single front/rear trimming unit: 0.3 HP motor. -- Double top & bottom trimming units; (2) 1/2 HP motors. -- Top & bottom scraper/radius scraper. -- Top & bottom buffing station; (2) 0.16 HP motors.NOTE: Edgebander was used for approx. (1) year before health issues forced closure of shop; has been stored & covered since.

CANTEK P 630HV Single-Sided Planer with Helical Head. --PLC digital control for auto-thickness setting. -- Sectional infeed roller and sectional chip breaker. -- Anti-kickback safety fingers for safe operation. -- Variable speed drive for optimum finish results according to the planing depth and material being planed. -- Quick-set table roll adjustment to aid in feeding difficult-to-feeling material. -- Steel spiral cutterhead with carbide inserts – 6 rows 86 inserts 30 x 12 x 1.5 mm cutters mounted on an angle for 'shear' cut. -- Exhaust hood with 6″ outlet. -- Flip open the upper hood for easy and convenient access to change the knives on the cutterhead. Safety limit switch on the cover will not allow the operator to run the machine with the hood open. -- 4 Table raising jackscrews.Specifications: -- Maximum planing width 24-3/4″. -- Maximum planing thickness 11-13/16″. -- Minimum planning thickness 3/8". -- Max. depth of cut 5/16″. -- Minimum length 8-3/4″. -- Table size 27″ x 34″. -- Feed speed 20-39 FPM Variable. -- Main motor 10 HP. -- Feed motor 1 HP. -- Power rise and fall of table 1/2 HP. -- Dust hood (1) 6". Machine dimensions: 51"; x 38"; x 47";. -- Shipping dimensions 44"; x 39"; x 52. -- Net weight 1804 Lbs. -- Shipping weight 2024 Lbs. -- Machine Electrics 230/3/60 - 31.6 amps, 460/3/60 - 15.8 amps. -- 575/3/60 - 12.8 amps

CANTEK CM626 Single-Sided Planer with Helical Head26" x 11-3/4" capacity Planer w/Helical Cutter HeadFeatures: -- Spiral cutterhead with (6) rows insert knives provides high removal, superior finish, and low noise. -- Solid cast iron construction. -- Variable feed speed. -- Drive top and bottom feed rolls. -- Front & rear bed rollers easily adjusted from the front of the machine. -- Power table elevation by digital thickness control. -- Serrated solid infeed roll. -- Section chip breaker. -- Anti-kickback fingers for added safety. -- Dual heavy jack screws with slides for accuracy & rigidity. -- Dust/Chip exhaust outlet 6"; in diameter. -- Sound dampening machine cover. -- All operations on a convenient control panel. -- Two-sided solid carbide inserts are easily changed while providing optimum wear lifeSpecifications: -- Maximum planing width 26" -- Maximum planing thickness 11 ¾" -- Minimum planning thickness 0.15"; (4 mm) -- Maximum depth of cut 0.31"; (8 mm) -- Minimum planning length 10.35" (263 mm) -- Table area 35" x 27" -- Feed speeds variable 16 – 70 FPM -- Main motor 20 HP -- Feed motor 1 HP -- Table motor 1/2 HP -- Knives 30 x 12 x 1.5 qty 100 -- Cutterhead 4 ¾" dia. x 5000 RPM -- Top feed rollers 3" dia. -- Dust hood outlet 6" dia.

CANTEK - P-630HV, ...24" Single Sided Planer with Spiral Knife CutterheadSpecifications: -- Planing width: 24-3/4"; planing thickness: 3/8" - 11-13/16". -- Max. depth of cut: 5/16". -- Min. length: 8-3/4". -- Table size: 26-1/2" x 33-1/2". -- Cutterhead speed: 5,600 RPM. -- Variable feed speeds: 20 - 39 FPM. Equipped with: -- 98 mm (3.86") Dia. Steel spiral knife cutterhead with: (6) Rows of (86) 30 x 12 x 1.5 mm inserts mounted on angle for shear cut & 10 HP Motor. -- 3" Dia. Sectional infeed roller with: 1 HP Feed motor & chip breaker. -- (2) 2-7/8" Dia. idler rollers in table; quick-set adjustment. -- 1/2 HP Bed elevation motor. -- eTEK "CH-525" Digital thickness controller with: LCD Display & Touchpad.NOTE: Seller purchased new and states machine has light use.

CANTEK MX340M Edgebander (Single Phase):The MX340 from CANTEK is designed to be a compact, and durable edgebander. -- Equipped with end trimming, flush trimming, PVC scraping, and buffing. -- The CANTEK MX340 Edgebander is operated through a PLC control system with an LED display and keypad.Specifications: -- The MX340 handles panel thiknesses of 0.315" up to 1.77" (8 mm to 45 mm). -- The coil feed accepts edgebanding from 0.4 mm to 3 mm thick, and strip material can be hand-fed. -- Conveyor feed speed is 29.5 FPM (fixed).Work stations: -- Heated infeed fence for optimum glue penetration. Large capacity Teflon coated glue pot (2.64 Lbs). -- Pneumatically operated guillotine for up to 3 mm thick banding, followed by spring loaded double pressure rollers. -- Single front/rear trimming unit 0.3 HP motor. -- Double top and bottom trimming units (2) 1/2 HP motors. -- Top and bottom scraper/radius scraper. -- Top and bottom buffing station (2) 0.16 HP motors.Also available in 220V/3PH/ 60 Hz

CANTEK P-630HV Planer24" Heavy Duty Single Sided Planer with steel spiral insert cutter head. Features: -- Sectional infeed roller and chipbreaker (3" dia.); -- Variable speed drive and Quick-set table roll adjustment. -- 98 mm (3.86") dia. steel spiral cutterhead with carbide inserts - (6) rows of Carbide inserts, 30 x 12 x 1.5 (86 inserts), 5,600 RPM cutter head speed. -- Exhaust hood with 6" outlet; Magnetic controls; (2) Idle rollers in table 2-7/8" diameter. Specifications: -- Planing width: 24-3/4", planing thickness 11-13/16"; Depth of cut: 5/16". -- Min. length 8-3/4". -- Table size: 27" x 34". -- Feed speed variable 20 - 39 FPM. -- Main motor: 10 HP; Feed motor 1 HP. -- Power raising & lowering of the bed 1/2 HP motor. -- Dust outlet: (1) 6" dia. and Limit switch on dust hood. Equipped with: PLC digital control for auto-thickness settingNote; ...Less than 200 Hours of Use.

CANTEK MX340 Edgebander (Single Phase)The MX340 from CANTEK is designed to be a compact, and durable edgebander. -- This machine is equipped with end trimming, flush trimming, PVC scraping, and buffing. -- The CANTEK MX340 Edgebander is operated through a PLC control system with an LED display and keypad.Specifications: -- The MX340 handles panel thicknesses of 0.315" up to 1.77" (8 mm to 45 mm). -- The coil feed accepts edgebanding from 0.4 mm to 3 mm thick, and strip material can be hand-fed. -- Conveyor feed speed is 29.5 FPM (fixed).Work stations: -- Heated infeed fence for optimum glue penetration. Large capacity Teflon coated glue pot (2.64 Lbs). -- Pneumatically operated guillotine for up to 3 mm thick banding, followed by spring loaded double pressure rollers. -- Single front/rear trimming unit 0.3 HP motor. -- Double top and bottom trimming units (2) 1/2 HP motors. -- Top and bottom scraper/radius scraper. -- Top and bottom buffing station (2) 0.16 HP motors.

CANTEK - MX340, ...Edgebander (Single Phase)The CANTEK "MX340" is designed to be a compact and durable Edgebander. -- Equipped with: End trimming, flush trimming, PVC scraping, and buffing. -- Edgebander is operated through: PLC Control System, LED display, and keypad.Specifications -- Panel thickness cap.: 0.315" to 1.77" (8 mm to 45 mm). -- Edgebanding coil feed accepts: 0.4 mm -3 mm Thick; strip material can be hand-fed. -- Conveyor feed speed: 29-1/2 FPM (fixed).Workstations -- Heated infeed fence for optimum glue penetration; large capacity Teflon coated glue pot (2.64 Lbs). -- Pneumatically operated guillotine: 3 mm Max. thick banding; followed by spring loaded double pressure rollers. -- Single front/rear trimming unit: 0.3 HP Motor. -- Double top & bottom trimming units: (2) 1/2 HP motors. -- Top & bottom scraper/radius scraper. -- Top & bottom buffing station: (2) 0.16 HP Motors.

CANTEK MT-610 24"; Rotary Milling PlanerSpecifications -- Heavy duty welded steel construction. --Moving table type -- Display position number. -- Alarm bell and flash light. -- Speed change for feeding, controlled by Inverter (VFD) -- Rubber Endless Belt. -- Automatic device for feed belt tracking. -- Air jet cleaner for cutter -- Working width 610mm -- Workpiece thickness 3-125mm Equipped with & Features -- Number of cutters -- 2 units Spindle motor power 20HP -- Brush motor power 1HP (150mm dia) -- Vacuum motor power -- 1HP (suction for conveyor belt) -- Feed motor power 1HP -- Lifting motor power 0.5HPVoltage

CANTEK MX340 EDGEBANDER (COMPACT): (Single Phase)The CANTEK "MX340" is designed to be a compact and durable Edgebander. -- Equipped with: End trimming, flush trimming, PVC scraping, and buffing. -- Edgebander is operated through: PLC Control System, LED display, and keypad.Specifications -- Panel thickness cap.: 0.315" to 1.77" (8 mm to 45 mm). -- Edgebanding coil feed accepts: 0.4 mm -3 mm Thick; strip material can be hand-fed. -- Conveyor feed speed: 29-1/2 FPM (fixed).Workstations -- Heated infeed fence for optimum glue penetration; large capacity Teflon coated glue pot (2.64 Lbs). -- Pneumatically operated guillotine: 3 mm Max. thick banding; followed by spring loaded double pressure rollers. -- Single front/rear trimming unit: 0.3 HP Motor. -- Double top & bottom trimming units: (2) 1/2 HP motors. -- Top & bottom scraper/radius scraper. -- Top & bottom buffing station: (2) 0.16 HP Motors.

CANTEK S251 24" WIDE BELT SANDERSpecifications: -- 24" Width cap. - sanding head with a rubber covered contact roll and adjustable finishing platen, 10 HP motor main drive motor. -- 25" x 60" Abrasive belts, pneumatic abrasive belt tensioning. -- 0" - 5.9" thickness capacity, Power elevation for thickness opening with digital thickness programming. -- Variable conveyor feed speed from 15 - 50FPM, 1 HP feed motor. -- 5.9" Max. working thickness, 13" min. working length, -- Spring loaded holddown rolls.Complete with: -- Magnetic controls, (2) 4" dia. dust collection outlets, and safety shutoff. - 825 CFM Dust collection required. Optional: 10 HP Single Phase motorElectronic belt tracking for optimum belt life and sanding results. Ammeter for load monitoring main drive motor. Disc brake on the main motor. Pneumatic belt tensioning with quick release outboard support. Safety Interlocks are located on all access doors.

Non-Oscillating Edge Sander with end sanding kit. -- 6" Wide x 108" long belt. -- 6" x 40" Graphite covered platen. -- 1 HP -1.5 HP, or 3 HP -2 HP, 3-Phase motor w/magnetic switch. -- 7" Diameter drive pulley. -- 7-3/4" x 37" Front table with a 6" vertical adjustment. -- End table for radius work with a 6" vertical adjustment. -- Heavy laminated tables, fabricated steel base and swing-away dust hood.

CANTEK - SS512TB Tilting Spindle ShaperSpecifications: --Tilting spindle from -5° to +45° and 6" x 43" fence. --1-1/4" interchangeable spindle is standard (other sizes available). -- Large cast-iron table is ground and polished for maximum stability and durability. -- Powerful 7.5 HP motor for even the most demanding profiling work. -- Five spindle speeds can be easily adjusted to suit your tool diameter. -- 5-1/2" Useable spindle length, above table 13-¼"; below table 8-¼". -- Electronic spindle brake for added safety and facilitates fast changeover. -- Precision fence assembly with micro-infeed and outfeed fence adjustment. -- The finger-style fence allows the fence to be adjusted around the cutter for added safety and workpiece stability. -- Table size 31 ½"; x 39.4″. -- Dust port (1) 5″ on guard, (1) 4" into the table.

CANTEK SS512CSB Heavy Duty Production Shaper with Sliding Table & Spindle Brake7.5 HP Features: -- Cast iron sliding table runs on ball bearing for smooth table transition. -- Cast iron ground & polished table with insert rings; table size: 31- ½"; x 39.4″. -- Precision ground and electronically balanced spindle. -- V-belt drive with (5) feed speeds is easily accessed from the front of the machine. -- Electric spindle brake for added safety. -- Spindle lock - with limit switch safety, machine will not start with lock engage. -- Micro spindle height adjustment with dial indicator. -- Interchangeable cutter spindle. -- Forward/reverse spindle rotation. -- Adjustable "finger" type fence Independent micro-fence adjustment on both sides. -- Includes the following standard equipment: 1- 1/4" Spindle, (1) 5"; dust chute on guard & (1) 4"; dust chute in the table, safety guard, Miter tenon jig, and Telemecanique magnetic controls.Net weight 1034 Lbs. Machine dimensions 48.4"; x 39.4"; x 52 ¾";. Shipping weight 1166 Lbs.Shipping dimensions 45 ¼"; x 37"; x 41";

CANTEK SS-512TSB Tilting Spindle and Sliding Table Shaper:7.5 HP - 3-Phase motor, overall table dimensions 31.50" x 39.40", sliding table 10.25" x 39.40". -- Spindle stroke 7"; 1-1/4" dia. spindle with 5 MT receiver and 4-3/4" cap. under the nut. Spindle tilts -5° & +45°. -- (5) Spindle speeds: 3,000, 4,000, 6,000, 8,000 & 10,000 RPM.Complete with: Spindle reversing switch, micro-adjustable fence 6" x 43", thermal overload protection and dust hood.16 weeks delivery.

102" Width cap. Veneer Clipper completely reconditioned to modern mechanical and safety standards to meet todays manufacturing needs. Original machine frame will be fully disassembled cleaned and repainted. The frame is the only part of the original machine used and all components are upgraded.Mechanical upgrades include:1. 2-Hand anti-tie back push button cycle activation 2. Photo safety eyes located on both front and back side of blade3. Full safety guarding including a fully enclosed knife section 4. New electric motor and gear box main drive system5. New knife and shear bar6. All new electrical/control box with Components and Wiring7. All new upgraded bearings including replacing Babbitt bearings Machine comes with a full (1) year warranty

CARGATE D-860 Rotary Veneer Lathe, Heavy Duty: -- Built specifically to handle large-diameter logs as well as small logs. It has a log length capacity of an easy 8'-6" and a diameter capacity of up to 5', peeling down to perfect 4" cores for optimal log utilization. -- This moneymaker looks like a big brother to a Premier Lathe. It comes complete with beefy Bull Gears and boasts plenty of output capacity along with the following main features and components:Specifications: -- BRUNETTE MACHINE WORKS Hydraulic Retractable Spindles - 4" inner, 8" and 11" outer. These are the same spindles as are utilized on a Premier Lathe. -- The spindles are driven by angle-cut 72" diameter Oil-Bath Bull Gears. (This is actually identical to an upgrade to Premier lathes still running.) -- Factory Hydraulic Backup Roll. (This backup roll rides on adjustable rollers riding down on top of the carriage. This prevents the backup roll from pushing excessively hard against the core. It produces perfect 4" cores).Equipped with: -- DURAND Charger and Pumps (self-centering). -- Factory Log Deck - Complete with S-drive and Gearbox. -- Factory Air Trash Gate, Infeed Conveyor (infeed to chipper). Infeed to PRENTICE Air Bag Clipper, Timing Wheel and Holddowns. -- Factory 5' Wheel, 6-knife, Veneer Chipper with Hold-down Drum Roller, and S-drive complete. -- 6' FERANO Chip Screen and Conveyor. -- Steel Framework and 450 FPM plus unwind speed!Highlights & Background: -- This lathe is capable of peeling very high production. In 1967 it was regularly peeling 225,000 sq. ft. 3/8 basis, or 400 - 500 cubic meters per 8-hour shift. The lathe is in wonderful overall condition and portions can be turned on today although it has not seen service since 2005. When you think "CARGATE" think "big PREMIER" and you will have the right idea.Price shown is in US Dollars. - Experienced Owner is flexible to assist in removal and perhaps installation.

Casadei R32 MK Pin Router