CEFLA TR3500/CT RUBBER ROLLER CONVEYOR48" infeed/outfeed power conveyor, 140" long, rubber roller conveyor.

2019 CEFLA, model ROC 3 D. Reciprocating Spray Machine:This sprayer can easily run at 30 feet per minute Machine consists of --a tilt-able up infeed belt conveyor with the Electronic Reading bar located over the entire width, this bar reads the parts as they enter the machine which controls the Gun spray pattern. --Parts are fed through the spray cabin by means of a Patented continuous CFB belt conveying system. --Sprayer is equipped with (2) two roll Overspray recovery systems. Belt cleaning is done by means of a counter-rotating roller's with scraper and belt cleaning unit. The rollers are fitted on the "cleaning" trolley which is pulled out from under the machine longitudinally by manual control. Motorized outfeed belt conveyor, tilt-able up to make access to the cleaning trolley easy. -- (2) Oscillating arms equipped to accept a maximum of (8) guns, driven by a Brushless motor's, the PLC in the control panel automatically triggers the guns based on thier size and location on the belt. -- This sprayer has (2) two separate lacquer feeding circuits and a pressurized cabin with both incoming air filtration and exhaust filtration. -- Air is pulled in from (2) air intake ducts (positioned between guns) above the slanted perforated top panels, perforations help to reduce turbulence -- Large front viewing window/access panel.

CEFLA TNS 3650/RBT BELT CONVEYOR146"L x 60" belt conveyor. 0.75 kW motorNOTE: Will need a new belt, not included in the price.

CEFLA TRC 2000 POWERED ROLLER CONVEYOR72"L x 60"W rubberized roller conveyor with .75kw motor

CEFLA TRC 2500 ROLLER CONVEYOR105"L x 60"W Rubberized roller conveyor with a .75kw motor

CEFLA KLEENSPRAY 12 Reciprocating Spray Line;The "Kleenspray 12" Reciprocating Automatic Spraying system is mainly based on the use of a closed continuous CFB belt conveying the panels to & through the spray area. The design has many advanced mechanical solutions to allow considerable advantages.KLEENSPRAY Technical Features: -- Non pressurized spray cabin, "Paper Belt Overspray Capturing" lacquer system; microprocessor unit for spraying operation control. -- 5-Edge coating, 51" max. width, 76" long spray enclosure. -- Gun Carrier: Reciprocating-type linear Gun Carrier with (4) guns; includes (1) station with "(4) guns, stainless steel material handling pumps", clamps & brackets for free height and angle settings. -- Supporting trolleys driven by toothed timing belts with brushless motor with electronic control, reciprocating slider, automatic reversal of gun angle on each stroke to cover panel edges, with variable speed; (3) lacquer feeding circuits. -- Light barrier gun control: Photo cell sensors send material size to the programmable controller which opens and closes the guns. -- Conveyor System: "Paper Roll" continuous collection belt with rollup collection paper area, with long life and easily removable infeed roller section with electronic reading barrier consisting of (60) photo diodes and outfeed roller. -- Booth Enclosure: Made of sandwich paneling with glazed elements; port for access to the spray guns units. The machine is particularly suitable for the application of waterborne drying lacquers; these products assure minimum environmental impact. Please Note: (4) Spray guns for UV paint& (4) guns for regular paint are included.Line Includes. -- VENJACOB Oven following the KLEENSPRAY. 600V/3/50-60 Hz. 230Vac/24Vdc. Control Voltage Max capacity 25 KW. Nominal Load 40 Amps.Year of Construction 2001. S/N 20104593 -- BURKLE UV Curing oven following the oven. Type TRUV2. (2) UV Lamp. Electrical 600/480V/360 Hz Control Voltage 24 Vdc. Nominal Power 49.5 HP.Nominal Current 99.8 Amps. S/n 010458-01. -- Pumps and pneumatic components. -- The panel cleaner shown at the start of the line is NOT INCLUDED.

CEHISA EP-7 EDGEBANDER1/4" Cap. edge thickness; min. panel size: length 4-3/4", width 3" and thickness 3/8", unlimited length & width; PLC controlled operation.Equipped with: -- Automatic strip feed & coil feed magazine, compact Hot Melt glue system, heats up in (7 - 10) Min, optional Heavy Duty guillotine for 3 mm thick PVC, 3-roll pressure section. Work Stations: -- Single motor end trim (0.3 HP), motor tilts 0° - 10° -- Top & bottom flush & bevel trim unit (0.75 HP ea. motor), tilts 0° - 20° -- Feed speeds of 33 FPM and a 1 HP feed drive.Complete with: Digital counters, sound enclosure, frequency inverter, telescoping outboard panel support & used tooling.

CEHISA PRO-12 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Features: Pre-Milling Station with:2 x 1.5 Kw (2.0 HP) 12,000 RPM motors, standard equipped with diamond cutters. Both spindles pneumatically controlled. -- Spray agent unit for top and bottom with (2) sprayer and (2) reservoir -- Automatic Edge Magazine: For coiled material up to 3 mm thickness, strip feed magazine for up to 5 mm (3/16") solid wood banding. -- Quick Melt Glue System, MR-5:10 - 15 min. heat-up time, auto temperature drop. Glue Tank is coated with nonstick material, quick-change mechanism for easy maintenance and/or color change. -- Pressure Section:(1) Large dia. driven and (2) idle rollers. Digital read-out and pneumatic positioning selectable from controller touch screen.Edgebanding Workstations: -- End Trimming Station, V-7: Double motor front & rear, 2 x 0.35 Kw (0.5 HP) - 12,000 RPM. -- Edge Trimming Station, BC-5: Top & bottom flush/bevel/radius trimming, 2 x 0.55 Kw (0.75 HP) - 12,000 RPM, tiltable 0° - 10°, pneumatic exclusion from operator panel. -- Corner Rounding Unit, FD-50: To process overhanging edges and trimming around the leading & trailing edge, 1 x 0.27 Kw (0.36 HP). -- Profile Scraping Unit, R-8: For thick PVC/ABS radius scraping, pneumatic in/out positioning from control panel with chip collection box. -- Flat Glue Scraper, RR-7: To remove potential glue squeeze-out. -- Buffing Unit, PC-9: with spry mist unit top/bottom Top/Bottom, 2 x 0.12 Kw (1/8 HP) - 1,650 RPM motors, tilting horizontally and vertically. -- Operator Interface:PLC Microprocessor control with color touch screen, memory up to 20 programs.Equipped With:Feed Speed, 9 - 14 MPM (29' to 45 FPM), -- Power hold-down beam, work-piece support outrigger, safety & sound enclosure. Included Options:Riepe, non-stick spray system. -- Nesting Tracer Shoes for top/bottom trimmers

CEHISA PRO 10 .EDGEBANDER (W/PREMILL): -- Features: Pre-milling Station with: 2 x 1.5 kW (2.0 HP) 12,000 RPM motors; standard equipped with diamond cutters. Both spindles pneumatically controlled. -- Automatic Edge Magazine: For coiled material up to 3 mm thickness, strip feed magazine for up to 5 mm (3/16") solid wood banding. -- Quick Melt Glue System: 10 - 15 Min. heat up time, auto-temperature drop. Glue Tank is coated with nonstick material, quick change mechanism for easy maintenance and/or color change. -- Pressure Section: (1) Large dia. driven and (2) idle rollers. Digital readout and pneumatic positioning selectable from controller touchscreen. -- Edgebanding Workstations. End Trimming Station: Double motor front & rear, 2 x 0.35 kW (0.5 HP) - 12,000 RPM. -- Edge Trimming Station: Top & bottom flush/bevel/radius trimming, (2) 0.35 kW (0.5 HP) - 12,000 RPM motors, tiltable 0° - 20°, pneumatic exclusion from operator panel. -- Profile Scraping Unit: For thick PVC/ABS radius scraping, pneumatic in/out positioning from control panel with chip collection box. -- Flat Glue Scraper: To remove potential glue squeeze out. -- Buffing Unit: Top/Bottom, (2) 0.12 kW (1/8 HP) - 1,650 RPM motors, tilting horizontally and vertically. -- Controller: "Unitronics V350" Controller with color touchscreen, memory up to (20) programs. -- Equipped with: Feed Speed: 9 & 14 MPM (29 & 46 FPM). -- Power hold-down beam, workpiece support outrigger, safety & sound enclosure. -- Included Options:RIEPE non-stick Spray System. -- Actual Model is: CEHISA PRO 10

CEHISA - PRO-9, ...Edgebander Single-Phase Electrical!Single-sided Edgebander with: End trim; top/bottom trimming; scraping; buffing.Specifications: -- 0.4 - 3 mm Edge thickness cap., -- Teflon coated glue pot system. -- Automatic magazine for strip & coil feed; Heavy-Duty guillotine for up to 3 mm thick PVC. -- (2) roll pressure zone with (1) motorized and (1) idle roller. Workstations: -- Double-motor end trim station; 0.33 HP - 12,000 RPM ea. motor. -- Top & bottom flush/bevel trim; bevels 0° - 20°; 0.45 HP ea. motor. -- Top & bottom PVC profile scraper; up to 3 mm radius. -- Last Station: Top & bottom buffing unit; 3/4 HP motors. -- Electronic braking on trim motors; digital readout on top/bottom trim. -- Feed speed: 33 FPM & 1 HP feed drive. -- Sound enclosure. -- Outboard panel support. -- Frequency converter. -- Digital readouts for trimmer adjustments. -- Sound enclosure.

CEMCO UF-37-1-103 SINGLE HEAD WIDE BELT SANDERSingle head Wide Belt Sander with 36" wide capacity; combination head with 6-1/8" diameter contact roll & independently adjustable platen. Equipped with: -- 30 HP main motor; 1 HP variable speed conveyor feed 30 to 50 FPM; and 1.5 HP Power Raising and Lowering Conveyor Bed Motor with hand wheel fine adjustment.. -- 37" x 103" abrasive belt size; -- Electric eye tracking. -- Single infeed and outfeed hold down rolls and Anti kickback finger devise on the infeed of the Sander, -- Load meter, disc brake on sanding head, and magnetic controls. Recently replace conveyor belt, Contact Sanding Roll and bearings.OVER BUILT for heavy loads. Grerat Sander for SLAB material.No longer required for ongoing operations.

CEMCO 1237 DUAL HEAD WIDE BELT SANDER2-Head, 36" cap. - 1st Head: Rubber covered contact roll, 20 HP motor; 2nd Head: Finishing platen, 15HP motor; 37" x 75" abrasive belts with air tensioning. -- Variable speed conveyor feed, 15 - 60 FPM, 0" - 6" thickness cap., infeed & outfeed rubber covered pinch rollers. -- Equipped with: Motor load meters, infeed conveyor extension, air disc brakes on sanding heads, emergency operator stop bar, and dust hoods. Actual model # "1237-SE".Seller recently upgrades to a 3-Head 52" wide Sander and this one is no longer needed

CEMCO - 4000, ...2-Head Wide Belt Sander38" Width cap. - Drum, Platen configuration.Head Configuration:1st Head: 40 HP -1,780 RPM rubber contact drum head.2nd Head: 30 HP - 1,775 RPM platen style head.Specifications: -- 3 HP 230/460/60/3 Feed motor with TOSHIBA VFD controls. -- 15 - 60 FPM Conveyor feed speed . -- 30 HP - 3,525 RPM Vacuum blower. -- Vacuum type rubber conveyor feed belt. -- Push button controls and amp meters. -- Electric ProScale digital thickness readout. -- YASKAWA Varispeed F7.Equipped with & Features: -- VFD abrasive belt drive system. -- Outfeed workpiece dust cleaning enclosure.Includes: Replacement abrasive belts and belt racks.

CEMCO 2000 Wide Belt Drum Sander, Single Head. --Specifications: Lightly used. Only 2180 Hours. -- Belt Size is 37" X 75"; 20 HP main motor,.1.5" top roller plus 2- 5" bottom rollers. One steel 1 rubber covered. -- Thickness is from 0" - 6". No Platen. Variable speed feed. Emergency brake. good. 4-1/2" dust port. -- Note: This machine was replaced 12 years ago with a triple head Cemco. Stored in a dry warehouse since then. Ran well until we unplugged it. All Cemco equipment is of commercial quality. This sander is a workhorse.

CEMCO MBV 54 Vertical Boring Machine54" x 15" Cast iron table with wooden top,Equipped With:(2) Universal spindles with movable spindle supports,(3) 2 HP - 1,725 RPM direct drive spindle motors,36" Stationary table height; 6" Max. vertical stroke, spindles advance hydraulically at 0 - 30 strokes/Min;Foot pedal actuated w/single cycle & continuous automatic modes;2 HP hydraulic feed pump, 12-gal. hydraulic pump system;Note: Riggers are required for loading

CEMCO SBV-120 Vertical Boring MachineSpecifications: -- 113" x 22" boring area Capacity, (14) 1.5 HP - 1,800 RPM motors driving (14) spindles, on/off switch controls for all motors -- Spindle nose with chuck 5/65" - 1/2" capacity -- 121" x 30.5" table size, (4) Spring loaded hold downs, -- 6" Spindle stroke adjustment with min. of 4" to max. of 10" between spindle nose and tabletop. -- Spindle assemblies advance hydraulically at 0 - 30 strokes/Min with single or continuous stroke -- 2 HP hydraulic feed pump w/variable speed control.Also included: -- 4 CHIP BLOW OFFS WITH INDIVIDUAL ON/OFF POSITIONS -- INSTRUCTION MANUAL/PARTS LIST -- DRILLING SAFETY GUARDS -- EMERGENGY STOP CABLE AND EMERGENCY STOP BUTTONFLOOR SPACE FOOT PRINT: 48: X 121"

DOUCET 12-SECTION Clamp Carrier (Hydraulic)Specifications: -- (12) Sections, 8-1/2' width, -- (9) Clamps per section (108) clamps total, -- 36" Clamp opening (rapid change) with 2-1/2" high jaws.Complete with: -- 5 HP hydraulic power pack and motor for rotation -- Hydraulic clamp tightening; -- Pneumatic overhead panel flattener.Note: Tear down not included

DOUCET ERS-96/RS-75/AP-508 MULTI-BLADE PANEL GROOVE/RIP SAW SYSTEM:The Doucet ERS-96/RS-75 Automated Panel GROOVE/RIP Saw System is designed to GROOVE and/or RIP panels as well as edge the sides of core materials. Ideal for plywood, OSB, MDF, HDF and other composite panels.This Line was originally designed for Engineered Flooring Blanks.ERS-96 Grooving Specifications:40 HP - 3,500 RPM belt driven saw arbor motor. Material width cap. 96" maximum. Material thickness 0.5" - 0.625" maximumGrooving pattern on 4" centers across the 96" width of panel. Depth and width of groove approx. 3/16" kerf/width by 1/8" deep.3" dia. Arbor shaft with 1.5 HP motor for motorized arbor adjustment for panel thickness. Saw arbor accessible from above for tool changes. -- Feed system:5 HP - 1,750 RPM feed motor, variable feed speed up to 75 FPM.(4) Powered bottom feed rollers & adjustable top idler pressure rolls with positive panel support during grooving operations.Top & bottom feed rollers have slip resistant urethane covered rollers, feed rollers are chain driven with air tensioning. -- Complete with:Dynamic saw arbor brake; Infeed anti-kickback fingers; Saw blade safety interlock cover; 12" dia. dust collection outlet (4,000 CFM required). RS-75 Ripping Specifications:40 HP - 3,500 RPM belt driven saw arbor motor. Material width cap. 60" maximum. Strip width cap. 2.5" minimum. Depth of cut 0.25" - 0.75" (6 - 19 mm) maximum.3" dia. Arbor shaft with 1.5 HP motor for motorized arbor adjustment for panel thickness. Saw arbor accessible from above for tool changes. -- Feed system:Doucet AP-508 Automatic panel feeder with scissor lift to automatically feed panels as needed.5 HP - 1,750 RPM feed motor, variable feed speed up to 75 FPM.(4) Powered bottom feed rollers & adjustable top idler pressure rolls with positive panel support during grooving operations.Top & bottom feed rollers have slip resistant urethane covered rollers, feed rollers are chain driven with air tensioning. -- Operator Interface: Doucet OI/HMI Control System for automatic loading & stacking with minimal human intervention other than a forklift operator to bring in new material and remove the processed parts/strips. -- Complete with:Dynamic saw arbor brake; Infeed anti-kickback fingers; Saw blade safety interlock cover; 12" dia. dust collection outlet (4,000 CFM required). -- Options Include: (1) Doucet AP-508 Automatic panel feeder with Indexing scissor lift. (1) Cross Transfer Chain Conveyor to feed panels sideways by the long edge through the Groover, max width 96". (1) Cross Transfer Chain Conveyor to feed panels short end wise through the panel RIPSAW, max. width 60" (1) Outfeed Lift Table to automatically stack ripped strips. Maximum weight of stack: approx. 5,000 LBS. -- Actual Model is DOUCET RS-75/ERS-96/AP-508

DUBOIS Vertical Edge Fill System with Micro UV This machine is designed to fill voids and defects in edges for a smooth, quality finish. These coaters are ideal for filling porous open grain panels like oak, veneers, particleboard, and MDF. Compatible with solvent based, water based, and UV fill coating.1.1 One (1) Continuous chain transport system- Top and Bottom chain transport conveyor with speed matching attachment conveyor chain- Aluminum backed chain pads with EPDM covering1.2 Two (2) double sided vertical edge denibber/buffer- Operator side Adjustable up to 12"; wide, back side fixed edge- Post mounted vertical denibber head- 12"; dia. x silicon impregnated scuffing wheel, buffer wheel to be determined- Dust hood with 4"; connection- Vertical head oscillation for even brush wear- Inverter controlled drive provides speed control for brush and oscillation1.3 Two (2) double sided vertical edge fill stations- Operator side Adjustable up to 12"; wide, back side fixed edge- Electric motor driven Applicator and Doctor roll drives- Quick change applicator sleeve design, 1-1/2"; face- Stainless steel distribution pipe with spring tension- 9"; dia. chrome plated reverse roll- Stainless steel catch pan and drain lines- 3/8"; pail mounted pump and agitator- Spring loaded doctor bar, urethane dr. blade- Air cylinder dr. roll engagement with stroke adjuster- Inverter controlled drives provides speed control for applicator and doctorrolls1.4 Edge Cure UV Oven Banks- Each bank to consist of Two (2) double sided Fusion F600 Microwave UVovens- Space for two (2) future double sided Microwave UV Units- Individually adjustable three (3) position lamp power selector switch(300, 400 & 600 w/in.)- Irradiator cooling exhaust fan for each set of four (4)2. Control Panel System- NEMA 12 Hinged Door Enclosure, with disconnect, required fuses, door mounted buttons and cooling fans- Allen Bradley HMI, PLC items included- Top mounted panel cooling fan- Required Inverters· Edge Fill Finishing Machineo Top and Bottom Conveyor driveso Denibber/Buffer Brusheso Denibber/Buffer oscillatorso Applicator Rollso Doctor Rollso Reverse Rollso UV oven Exhaust fansDesign Parameters- Machine is located in Explosion Proof Area- Voltage= 480 V., 3 Ph., 60 Hz.- Design Speed = 70 - 200 FPM- Line height = 36";- Max./Min. Part Width: 12"; / 2";- Max./Min Part Length: 245"; / 24";- Max./Min Part Thickness: 1-1/4"; / 3/8";- Paint Color· Main Frame and Conveyor: Blue / TS White· Guards: safety yellowNotes:- ¼"; product has the potential of being processed in this machine but has less probably of being successful the wider the product.

DURAMAC - DUR52-2, ...2-Head Wide Belt Sander2-Head Wide Belt Sander with: Drum, combi-head, and brush cleaner. -- Max. working width: 52". -- Max. working thickness: 6". -- 23" Infeed load space. -- 50" Wide rubber conveyor belt size. -- 1st Head: Grooved rubber contact sanding drum; 40 HP, 230 Volt - 3-phase drive motor. -- 2nd Head: Combination contact drum & polishing platen; 30 HP, 230 Volt - 3-phase drive motor. -- Spring-loaded pinch rollers. -- Electronic belt tracking, pneumatic belt tensioning. -- (1) Rear top outfeed panel brush cleaning head, 0.5 HP, 230 Volt - 3-phase drive motor. -- Power raise & lower of worktable. -- Inverter driven feed works drive motor for variable speeds, 0 to 60 FPM. -- Front operator control station; motor ammeters. -- TOSHIBA Feedworks inverter. -- "DP-626S" electronic digital readout for setting table heightAlso Available: -- Transformer for 600 Volt operation, 112.5 KVA.