Woodworking Equipment For Sale

TIMESAVER - 113, ...12" Width Single-Head Wide Belt Sander12" Width cap., single drum.Specifications: -- 12" Width capacity. -- 7.5 HP Main motor. -- 6" Dia. drum. -- 0 - 8" Opening capacity. -- 0.5 HP Feed motor. -- Complete with: Posi-Trac electronic tracking and a 12" conveyor extension.

Timesavers Single Head Sander Combination Head Model 2311-45-6 Includes transformer

Only 697 hours, taken from service (2) top heads - one orbit, one brush (1) 3HP main orbit motor (1) 3HP feed motor (1) 1HP brush motor (1) 1HP oscillation motor 460V Max. stock width 36" Max. thickness 6" 32-38" variable passline height 2,000 CFM @ 5,000 FPM exhaust air requirements

TIMESAVERS - 4321-45-01, ...2-Head 52" Wide Belt Sander.Head Configuration:1st Head: 9-1/2" Dia. rubber-covered contact roll, infeed & outfeed spring-loaded holddown shoes & pinch rolls; 40 HP Motor.2nd Head: Combination head with: 6" Dia. Rubber-covered contact roll & 2-1/2" wide Platen, infeed spring-loaded holddown shoe & outfeed double pinch rolls; 30 HP motor. 3rd Station: Panel Cleaning Brush.Specifications: -- 6" Thickness capacity. -- Variable speed feeds from 15 - 45 FPM. -- 52" x 103" Abrasive belt size.Equipped with & Features: -- Automatic part thickness adjustment with digital thickness indicator. -- Dual "POSI-TRAK" electronic abrasive belt tracking. -- Air caliper disc motor brakes and load meters. -- Infeed safety stop bar.

Timesavers 43" Speedsander Single Phase Machine

Timesavers Model 2321-24-01 Sander 43"x75" Belts 2-Head IceClean System on each head

Timesavers Model 2331-04-334 3-Head Orbital Sander 43" Machine

TIMESAVER - TB-440-4, ...2-Head Wide Belt Sander40" Width cap.; Drum and Combination Head.Head Configuration:1st Head - 50 HP; 12" rubber covered contact head.2nd Head - 40 HP; combination platen head.Specifications: -- Sander completely rebuilt (15) years ago. -- Rubber covered abrasive rolls were recovered, grooved and balanced, along with ALL pinch rolls recovered at FLETCHER MACHINE CO., Lexington, NC. -- Electric eyes upgraded to BANNER's send and receive type; includes battery backup system for controls (no crashes when machine has power outage). -- Feed speed gear box driven by AC Drive controlled 10 HP motor. -- Rebuild included: Table removed and platens ground flat; all bearings replaced, including pinch rolls and tracking cylinders; tension cylinders plasma sprayed, reground & new factory seal kits. -- Entire machine was disassembled, sand blasted and DUPONT "Zolatone" primed and painted. -- RAINBOW brand feed conveyor belt replaced in 2014. -- Many more upgrades, too many to list: Please contact for additional information. -- Machine is in good condition, running daily, and has had regular recommended service intervals; includes all factory manuals, blueprint drawings, parts list with numbers supplied, and when machine was new. -- Machine used in solid wood wide belt sanding. -- Includes Cloth aluminum Oxide Belts: 7 - 50 grit; 1 - 60 grit; 8 - 80 grit; 2- 120 grit; 8 -1 80 grit..

TIMESAVERS 4331-45-001 Wide belt sander (3) heads 51" width cap. 1st Head 9-1/2" Dia. rubber covered (60-65 Duro) 40HP motor 2nd Head 9-1/2"Dia. rubber covered (60-65 Duro) 30HP motor 3rd Head Combination head with 6" dia rubber covered contact roll and a 2-1/2" finishing platen. 30HP motor. 52" x 103" abrasive belts with dual "posi-trac" electronic-solid state tracking Controls mounted on belt loading side Conveyor feed belt replaced (2) years ago.

Dust Collection System

Reconditioned Torit 156RF10 baghouse

TORREDA TORMADEX S.A. PA-1200 Hydraulic Wood Turning Back Knife Lathe:Nicely equipped Spanish lathe with dual hydraulic tracers for making quick work of all your demanding woodturning production runs! ... Great for turning baseball bats!Specifications: -- 47" Max. between centers, 9-7/8" max. dia. without traveling steady. -- 3-1/3" Max. dia. through steady rest (larger dia. of 6.2" cap. OPTIONAL); -- High speed automatic loading, feeder accepts pieces up to 4" square. -- 4 HP Motor with (4) turning speeds, 1,200, 2,800, 3,500, and 4,550 RPM. -- (2) HIDRO "T-75" hydraulic reproducing heads with 3" stroke. -- (2) Top mounted hydraulic knives for tenon or pattern cutting (accepts form tools up to 3" wide). -- 2 HP Hydraulic pump motor with (3) carriage feed speeds. -- Features: Pressure sensitive Hydraulic tailstock with Pressure Regulating Valve needed for small, slender turnings to avoid buckling. Pre-rounding tool in front of travelling steady rest. -- Includes: Safety guard, tooling with several roughing and finishing knives.

TORREDA METOR 1600 UNIVERSAL Copy Lathe; -- Specifications: 63" (1,600 mm) Max. between centers, 9-7/8" (250 mm) max. dia. without traveling steady, 3-1/2" (90 mm) max. dia. through steady rest (larger dia. of 6-1/4" (160 mm) cap. OPTIONAL). -- Equipped with: 4 HP Motor with adjustable turning speeds, (1) HYDRO hydraulic tracing head with 3" stroke, hydraulic controlled tailstock. -- (2) Top mounted manual knives for tenon or cutting using form tools (accepts form tools up to 3" wide); 2 HP hydraulic pump motor with adjustable feed speeds. -- Actual model is HIDRO 80/12 mm. -- Includes matching knife grinder and accessories as pictured

TRAVAINI TRO 501-1A-200V "40 HP VACUUM PUMP (LIQUID RING) 11,969 Hours:40 HP Travaini liquid ring, single stage vacuum pump "TRSC 100-700/C/F". Nominal capacity 500 ACFM @ 20" HgV; max Vacuum 27" HgV. -- Pump materials:Include cast iron housing, ductile iron impeller, and stainless steel shaft. Shaft seals are carbon face with viton elastomers. -- 40 HP:200 Volt, 3-Phase, 60 Hz, TEFC monoblock assembly for direct drive, no field alignment needed. -- Sealing fluid re-circulating system includesReservoir of carbon steel with fluid level gauge and drain, high-efficiency discharge separator and oversized heat exchanger. -- High temp switchTo protect against over-temp operation. -- Suction line accessories includeInlet check valve, vacuum gauge (0 - 30" HgV), inlet filter assembly, manual unloader valve, and vacuum relief valve. -- Heat exchangerIs an air cooler type made from aluminum and extended surface fins. -- Electrical controls include:Starter/overload reset, pump running light, hour meter, hi-temp light, and terminal blocks, all mounted in a NEMA 12 cabinet.

Tri State Machinery Straight Line Rip Saw S/N 4.5.74-72

Twin City Fan Blower Air Lock Can BE Added For Additional Cost

TWIN FLOW Air Make-Up Unit 7,000 CFM. Vertical mount with Remote Control Panel: -- CFM: 7,000 CFM @ 1.75" ESP, 5HP/575v/3ph/60Hz TEFC motor -- BTU: 0.68 MBTUH -- Burner: MAXON burner -- Temperature Control: 80º F temperature rise in spray cycle -- Mounting: Vertical, outdoor/indoor mounted -- Fuel required: Natural gas, 0.3 PSI pressure -- Intake/Discharge: Vertical, screened, air intake with vertical discharge -- Filter Sections: V-Bank style with 1’’ cleanable air intake disposable type filters -- Gas Control: Control cabinet and pre-piped gas combustion system mounted on burner section to FM, Electronic Modulation -- Specifications includes: Digital Temperature Controller, ON/OFF & Summer/Winter Switch, pressure regulator, metering valve, pilot pressure regulator & pilot gas valve, flame rod, high limit switch, air flow switch, power transformer, ignition transformer and spark plug -- Electrical Control cabinet includes: main breaker disconnects, magnetic motor starters with adjustable overload protection for air makeup, motor fuse protection -- Motor Control: Control cabinet includes: main breaker disconnects, magnetic motor starters with adjustable overload protection for air makeup, motor fuse protection -- Enclosure Design: Framed, with 18 ga. metal walls and 1" insulation -- Note: Available in Horizontal and Vertical mount. Please inquire.

TWIN FLOW Air Make-Up Unit 14,000 CFM. Vertical mount with Remote Control Panel: -- CFM: 14,000 CFM @ 1.75" ESP, 10 HPTEFC motor -- BTU: 1.38 MBTUH -- Burner: MAXON burner -- Temperature Control: 80º F temperature rise in spray cycle -- -- Mounting: Vertical, outdoor/indoor mounted -- Fuel required: Natural gas, 0.3 PSI pressure -- Intake/Discharge: Vertical, screened, air intake with vertical discharge -- Filter Sections: V-Bank style with 1’’ cleanable air intake disposable type filters -- Gas Control: Control cabinet and pre-piped gas combustion system mounted on burner section to FM, Electronic Modulation -- Specifications includes: Digital Temperature Controller, ON/OFF & Summer/Winter Switch, pressure regulator, metering valve, pilot pressure regulator & pilot gas valve, flame rod, high limit switch, air flow switch, power transformer, ignition transformer and spark plug -- Electrical Control cabinet includes: main breaker disconnects, magnetic motor starters with adjustable overload protection for air makeup, motor fuse protection -- Enclosure Design: Framed, with 18 ga. metal walls and 1" insulation -- Note: Available in Horizontal and Vertical mount. Please inquire. -- Also available: Controls option: - Two stages for 14,000 or 7,000 CFM at extra cost of about $3,000.

ULTRA GL-630H Feed Through Moulder: 6-Head (B-T-R/L-T-B), "Flooring" working capacity of 12" x 6".Specifications: -- Head sequence: Bottom 25 HP, top 30 HP, right 20 HP/left 20 HP (opposing), top 25 HP, and bottom 25 HP motor. -- Spindle dia. of 1-13/16" with cutterhead speed of 6,000 RPM; all spindles with high prevision bearings. -- Auto. positioning of the left & top spindles radially; all additional spindles with digital readouts, including chipbreaker & pressure elements. -- Pneumatics on all chipbreakers, pressure elements, and holddown rollers. -- Horizontal spindles with HydroLock outboard bearings on #1, #2, #5 & #6. -- Straight jointer on spindles #5 & #6; Profile Jointers on spindles #3, #4, #5 & #6. Equipped with: -- Inverter controlled feed drive, variable speed of 26 - 260 FPM. -- Infeed table 1.2 M (4') with all table plates & fences hard chromed to RC 70. -- Machine table includes: (5) Table rollers for smooth through feed; short stick attachment for through feed on pieces down to 230 mm. -- Electrical cabinet & pedestal for machine controls separate from machine, Heavy Duty sound enclosure. -- Includes Startup training and Warranty!

UNIQUE "318-3" Rail MachineThe UNIQUE "318-3" Rail Machine is designed to cut precise profiles in rails, ideal for higher volume or production applications. -- Climb cutting provides better than moulder quality cuts, capable of cutting up to 35 FPM. -- Equipped with: 10 HP HIMMEL Direct Drive Motor, 1-1/4" Spindle with 5-1/4" stack height for tooling with up to (3) cutters on the spindle. -- Max. Material width 8", max. material thickness 2", Z-axis spindle movement adjustable with a digital indicator. -- Complete with:In-feed fence with digital read out, dust collector hood with 4" outlet; emergency stop and cutter shields.