Veneer Equipment For Sale

--In Auction--Starting bid: $100-- Schuetz Tool Bladder Press Specifications: (2) Shuttle tables, approx. 55” x 106” press capacity. Hot air design with 3mm silicone membrane to press veneer into profile, typical cycle time 3 minutes using proper glue that sets at 200°F. Can use PVA which would extend cycle time to approx. 15 > 45 minutes depending on the actual glue mix used to achieve 80%+ cure strength. Includes Hydraulic Pump. SPECIAL NOTE: Fully operational, however, need 4 or 5 heating rods replaced, new rod parts are included for you to install ( don't have the capability to remove them). The current average operational temperature is 150° F. NOTE: Above specs are taken from literature and thought to be accurate. As always please take advantage of the inspection period to verify. Items seen in the background are NOT a part of this Lot.

Engineered Flooring Line For Sale Producing specialty flooring for Japanese market. They produced about 1500 to 2000 sq ft per day with 5 employees, including the manager. Full production would be about 8-10,000 sq ft per shift, with 15 employees. The market collapsed in 2001, and the flooring line was put into storage. Call 800-459-2148 for more info.

Vac-U-Clamp FT800+ Thermofoil Press 52" x 105" Work area Dispenser Rack (3) Vac bags new in boxes still

Vac-U-Clamp FT900 Thermafoil mPress Brand new - Seller never used it!

The Vantec 2800mm Spindleless Veneer Lathe is designed to process veneer for plywood production from both hard and soft logs. Its metal tempered grooved rollers and lathe knife inclination system work perfectly to make sure there will always be a precise contact area between the lathe knife and the log during the peeling process by eliminating vibration that could cause damage to the Veneer sheets. Vantec Spindleless lathe proves its efficiency by delivering consistent thickness variation and a impressive top linear speed of 180 m/ min throughout the peeling process for face or core veneers with smooth surfaces. - Log diameter up to 600 mm; - Max log length: 2750 mm; - Min log Length: 2300mm; (with stacker) - Min log length:1800mm (no stacker); - Veneer thickness: 1.0 to 4.0 mm; (Pine and eucalyptus); - Log core after peeling: 40 to 45mm; - Maximum linear speed 180 m/min; - Drive panel included; - Each motor is individually connected by a Variable Speed Drive for torque control in two points of traction on the rollers to pre- vent excessive load on tip ends; - Log Central aligner with maximum of 2200 mm of movement; - Pneumatic scriber Knives (02 fitted on the sides to cut in width and 01 in the Center to cut the length); - Width: 7640 mm; - Length: 3400 mm; - Height: 2550 mm; - Approximate weight: 14000 kg.

The Vantec Automatic Rotary clipper is designed to clip 2800 mm veneer sheets into specific sheet sizes as per the auto stacker preselection. It comes with electronic drive panel, automatic gauge system, positioning of clipper knife by Servomotor and encoder. It is de- signed to work with one tensioned clipper knife with gear motor. It also comes with a 2 HP motor on the output. The clipper knife is not included. - Veneer Thickness : 1 to 4 mm; - Max. Log: 2.750mm; - Minimum veneer width cut: 800 mm; - Max. Veneer length cut: 2700 mm; - Min. Veneer length cut: 700 mm; - Min. Venner rounding length: 150 mm; - Rotor gear motor: helical gears; - Clpper rollers power drive: 4 hp 6P; - Outlet conveyor Motor: 2hp 4P (input) 1 hp 8P (output); - Clipper Servomotor: 40 Nm (2x); - Width: 4800 mm; - Length: 6000 mm; - Height: 1700 mm; - Approximate weight: 7.000 kg

The Vantec Veneer Auto Stacker, ELV 1.82B is a Vacuum stacker for 2800 mm Veneer lathe. It is fitted with double stacking system (04 bins), with four veneer transport lines and four 5hp exhausters. with of two stoppers and eight ejecting arms. With drive Panel, VSD for exhaust fans and hydraulics lifting tables. Min veneer sheet length sheet: 2300 mm; • Max veneer sheet length sheet: 2700 mm (or Two sheets of 1350mm); • Min veneer sheet width: 800 mm; • Max veneer sheet width: 1500 mm; • Max height of stacks: 1000 mm; • Exhaust motor: 10 hp 4P (8x); • Inlet conveyor motor: 2hp 8P; • Transport conveyor motor: 6hp 4P; • Hydraulic pump motor: 5hp 4P (3x);

Wemhoner Variopress

WEMHONER Hot Oil Feed Thru Press, 7’ x 12’ Platen, 7.5’ x 13’ motorized feed belt, 340 Ton pressure, 8 cylinders, 6” opening, 12’ gravity outfeed conveyor, Includes natural gas boiler for hot oil., Machine is no longer in service and disassembled. Call 800-459-2148 for more info.