Woodworking Equipment For Sale

EXTEND LIGHT - GY610S: Double-Sided Strato Planer 24" x 8" Cap., min. material length 12-1/2" and min. thickness 3/8".Equipped with: -- 25 HP Top & 20 HP Bottom belt drive motors. -- Helical Spiral cutterheads that rotate @ 4,600 RPM; (6) rows or spirals of 4-sided carbide inserts 15 mm x 15 mm. -- Variable feed speed from: 20 - 95 FPM; powered by: 3 HP drive to lower feed rolls & upper feed mat. -- Infeed table: Hard chrome plated for max. wear resistance; relieves upper feed mat with spring-loaded spikes; allows cupped bowed or warped boards to feed into the heads for max. straightening capability. -- Powered lowering & raising of bed table on: (4) Columns via a 1 HP motor; handwheel for fine adjustment of thickness control. Includes -- Spiral cutterheads; digital control for accurate thickness setting. -- Side-mounted electrical control & Operator Panel. -- Automatic feed chain tensioning. -- Staggered upper infeed fingers to eliminate small part jambs.

EXTREMA - XR-12LE: Straight-Line Rip SawCompact Straight-Line Rip Saw with: Guaranteed 8' glue line. -- Powered by: 15 HP Direct drive motor. -- Equipped with: WYE-DELTA Soft Start for: Lower amp requirements during startup. -- Heat-treated chain & raceway with automatic oiler. -- All SQUARE D electrical controls. -- Large: 14-3/4" Rip capacity. -- Overarm control box: Mounted on the infeed side. -- Total space requirements: About the same as a standard size Table Saw.

37" width capacity Single head 60" belt length Digital thickness controller Electronic belt tracking vVariable speed drive

EXTREMA - EXCESS XS-1E37: Single Head Wide Belt Sander37" Width capacity; 0" - 6" conveyor bed opening.Mono-block construction for: Solid, vibration free operation; increased durability. -- Equipped with: Combination sanding head with: Rubber-covered contact roll; graphite covered platen. -- Over thickness material feeding safety device. -- Digital material thickness controller setting with: LED Readout accurate to a thousandth of an inch. -- "Automatic Thickness Setting" device for easy setup. -- OMRON Electronic abrasive belt tracking. -- GOODYEAR Endless conveyor belt with: Automatic belt tracking. -- 20 HP Main motor. -- REGAL Variable feed speed drive unit; 2 HP motor. -- 1/2 HP Power elevation motor. -- Large cabinet style doors for easy service access. -- Pneumatic abrasive belt tensioning. -- Double infeed & outfeed covered holddown rollers. -- Infeed conveyor extension with: Safety stop bar; emergency stop button; motor load meter.

EXTREMA EXCESS XS-1E37 SINGLE HEAD WIDE BELT SANDER37" Width capacity, 0" to 6" conveyor bed opening. Mono-block construction for solid, vibration free operation and increased durability. -- Equipped with: Combination sanding head with rubber covered contact roll & graphite covered platen. -- Over thickness material feeding safety device. -- Digital material thickness controller setting with LED readout accurate to a thousandths of an inch. -- "Automatic Thickness Setting" device for easy setup. -- OMRON Electronic abrasive belt tracking. -- GOODYEAR Endless conveyor belt with automatic belt tracking. -- 20 HP Main motor. -- REGAL Variable feed speed drive unit; 2 HP motor. -- 1/2 HP Power elevation motor. -- Large cabinet style doors for easy service access. -- Pneumatic abrasive belt tensioning. -- Double infeed & outfeed covered holddown rollers. -- Infeed conveyor extension with safety stop bar, emergency stop button and motor load meter. -- Operations manual & free box of 3M Sanding Belts. -- Optional 460 Volt / 3 Phase.

EXTREMA XS-1E43 Single Head Wide Belt Sander42" Working width, up to 5" max. opening with electronic digital microprocessor thickness control.Equipped with: -- Rubber-covered contact drum and 2-1/2" wide finishing platen, 25 HP main motor; -- 43" x 60" Abrasive belt, TRU-TRAK solid-state electronic belt sensing with pneumatic tracking. -- GOODYEAR Endless conveyor belt with pneumatic tracking, 2 HP variable speed feed motor from 15 - 48 FPM. -- 0.5 HP Motor to raise & lower table via (4) jack screws, an over-thickness bar at the infeed of machine, and AUTO-SET thickness device. Complete with & Features: -- Double infeed & outfeed rubber covered holddown rolls. -- Air operated disc brakes on main motor, front & rear emergency stop buttons, and motor load meter. -- SQUARE D Electrical controls; magnetic Starter with overload protection, and electrical interlock at sanding belt access doors.NOTE: Also available wired for ...460V operation.

EXTREMA PERFORMA XS-2P52 Wide Belt Sander (2) Heads;52" Width cap. Drum, Roller and Platen - 75"; Belt Lengths Head Configuration: -- 1st Head: Contact drum 30 HP motor; -- 2nd Head: Roller and Platen 30 HP motor.Features: -- Over thickness safety device -- Infeed bed rollers -- Digital thickness controller -- Individual amp meters -- Disc brakes on sanding heads -- Telemecanique electrics. -- Camozzi pneumatics -- Variable speed drive system.Specification: -- Feed motor 3 HP -- Elevation motor 0.5 HP -- Max. thickness 6" - Min. thickness 1/8" -- Contact drum 1st head 8" dia. -- Roller drum on 2nd head 5" dia. -- Dust Collection requirements 4800 CFM -- Feed speeds 15 - 50 FPM. -- Weight 6500 Lbs -- AMPS (220 V / 460 V ) 148/74.

EXTREMA 126TV Single Sided Planer;26" Max. width capacity, 11.75" thickness, Solid cast iron construction. -- Precision ground cast iron table with motorized programmable height adjustment; 1/2 HP elevation motor. -- 20 HP Main drive motor -- Scale & pointer readout for accurate thickness adjustments. -- "VECTOR" cutterhead with (6) rows of 4-sided inserts. -- 1 HP Feed drive, variable feed speed setting from 20 to 75 FPM. -- Sectional steel infeed roller & segmented chipbreaker. -- Independently adjustable feed rollers; (2) Externally adjustable bed rollers. -- Hinged top for easy access to cutterhead & gear assembly. -- Self-braking motor with magnetic starter & thermal overload switch and Emergency stop. -- Includes Operations manual, parts list & tool kit.

EXTREMA XP-124TV Single Head PlanerSpecifications: -- Solid cast iron construction. -- 15 HP Main drive motor, 1 HP feed motor 20 to 70 FPM, 1/2 HP elevation motor. -- Precision ground cast iron table w/motorized programmable adjustment. -- Scale & pointer readout for accurate thickness adjustments. -- "VECTOR" insert cutterhead with (4) sided inserts. -- Fixed feed speed setting for consistent stock removal. -- Sectional steel infeed roller & segmented chipbreaker. -- Independently adjustable feed rollers. -- (2) Externally adjustable bed rollers.Features: -- Hinged top for easy access to cutterhead & gear assembly. -- Self-braking motor. -- Magnetic starter & thermal overload switch. -- Emergency stop. -- Operations manual, parts list & tool kit. -- Options: Single-phase power, please add ...$ 100, 460 volt add...$ 150.

EXTREMA XP-610 SINGLE SIDED PLANER24" Width capacity, 8-3/4" thickness, solid cast iron construction. -- 10 HP main drive motor -- Precision ground cast iron table w/motorized height adjustment, with digital thickness display; 1/2 HP elevation motor. -- Scale & pointer readout for accurate thickness adjustments. -- "VECTOR" cutterhead with (6) rows of 4-sided inserts. -- Variable feed speed from 20 to 42 FPM; 1 HP feed drive. -- Sectional steel infeed roller & segmented chipbreaker. -- Independently adjustable feed rollers. -- (2) Externally adjustable bed rollers. -- Hinged top for easy access to cutterhead & gear assembly. -- Self-braking motor with magnetic starter & thermal overload switch. -- Emergency stop. -- Operations manual, parts list & tool kit.

EXTREMA XP-615 Single Sided Head PlanerSpecifications: -- Width: 24" -- Main HP: 15 HP -- Feed HP: 1 HP -- Elevation HP: 0.5 HP -- Max. Thickness: 8.75" -- Min. Thickness: 0.375" -- Max. Cut: 0.25" -- Min. Length: 10.5" -- Cutterhead Speed: 6000 RPM -- Feed Speed: 20-42 ft/min -- Air Requirements: 1000 CFM -- Thickness Adjustment: PLC ControllerBed Roller Adjustment: External -- Powered Bed Rollers: Top and Bottom -- lnfeed Roller: Standard -- Amps (230V / 460V): 41A/20A -- Weight: 2345 LbsFeatures: -- Solid cast-iron construction -- Sectional infeed rollers -- Huge 8-3/4"thickness capacity -- 6000 RPM cutterheads -- Anti-kickback fingers -- Segmented chip breakers -- Sectional feed rollers -- XP-615 Digital Controller -- Motorized table elevation -- VECTOR Carbide insert helical cutterhead -- Heavy duty screwjack elevation system -- Easy access internal workings -- External bed roller adjustments

EZ SANDER EZ-3760 Wide Belt SanderEZ-Sander's are built to with the ability to hold very tight tolerance (+/-.003) side to side when set up properly.Specifications: -- The sanding head is a combination head that consists of a 5" rubber-covered contact drum for the more aggressive sanding and then followed by an adjustable 2-1/2" graphite-covered felt polishing platen for doing very fine finishing sanding using a 37" X 60" abrasive belt. -- The conveyor belt speed is set to run at 10 - 30 FPM and is controlled via AC variable speed unit mounted in the main control panel. Simply adjust the dial setting to your desired feed speed. -- Double infeed and outfeed hold-down rolls are provided to help ensure proper part feeding through the Sander. -- The conveyor table/bed opening has a 0" to 5" opening allowing the operator to sand some parts as thick as 5" and the ability to sand very thin parts as well. -- Power raising and lowering of the conveyor bed is standard. -- Digital thickness display is standard.Complete with & Features: -- EZ Sander is equipped with a state-of-the-art electronic tracking system for the abrasive belt. -- Emergency stop heavy-duty caliper disc brakes bring the sanding head to a stop within 4 to 5 Sec when activated by the machine's safety interlock system. -- Limit Switches on both sides of the abrasive belt to keep the belt from over-travel. NOTE: -- Available in single phase with a 7.5 HP or 10 HP 3-Phase main drive motor. -- Voltage change to 440 Volt ...$275.

GENERAL SPECIFICATIONS X – Axis: 62.99 inches Y – Axis: 157.48 inches Z – Axis (Without Tool): 7.87 inches Total Power Consumption: 24.0 HP Max. Rotation Speed: 18,000 RPM Tool Holder ISO: 30 FEATURES: Used for v-channel opening, processing and sizing operations of composite panels and plates. Composite plate fixing and superior processing quality with strong vacuum Tool replacement magazine: capacity for 4 independently operating fan cooled spindle motors Ability to process wooden and plastic plates by replacement of milling cutter Ideal vacuuming with air channels on polyethylene board 2D CAD CAM graphics and optimization software Tools replacement in 2.5 seconds Vacuuming in independent sections Automatic milling cutter length reset External dust vacuuming system NC-300A – MI CNC Control unit Automatic, pneumatic alignment system Data transfer over remote network connection, Ethernet and USB Remote access Steel frame with tension resistance, high accuracy processing Special vacuum circuit designed for local vacuum delivery Ability to resume operation following problems such as power outage, etc. Ability to edit loaded code file Ability to write and process manual code ? Standard Equipment: 2D CAD CAM Cutter (2 pcs 0.15 inch cutter, 2 pcs V channel cutter) Vacuum pump Dust vacuuming system

•? ?Year of construction 2004 •? ?Operating side left •? ?Working width 1.300 mm •? ?Working height 900 mm + - 20 mm •? ?Gun drive single version •? ?Dry extraction •? ?Extraction nozzle diameter 490 x 350 mm •? ?Exhaust air capacity 6,500 m?/h •? ?Paper belt transport system •? ?Infinitely variable feed speed 1.5 - 7 m/min •? ?PLC control with touch screen •? ?Number of spray guns installed 0 pcs. •? ?Height-adjustable spray guns •? ?Number of paint pumps 0 pcs. •? ?Suitable for solvent-based paints •? ?Suitable for water-based paints •? ?Length 4,450 mm •? ?Width 3,360 mm + 1000 mm •? ?Height 2,600 mm - Total connection ~ 7.1 KW / 28.6 A •? ?Volt, Hz 400 / 50 - Location, in stock in Italy •? ?Voltage fluctuations max. +/- 5

Cabinet Door Finishing System --4 Air Spray Guns --3 different lines and pumps --Paper feed belt with various speed options --Infrared sensors detect exact measurements of cabinet doors or mouldings and spray only the pieces being sent through. --System includes: (1) Dry Room and fan for air movement. --System is in great condition and works well. Our shop got to the point where we were really only using it to prime doors and it is capable of so much more than that.

Fanuc Robot with Controller Box and Teach Pendant Model: S-420iF Type: A05B-1313-B501 Part #: R98Y03430 Date: 1998.11

3 available 3 phase power Very low hours

2 available 3 phase power liow hours

Fay and Egan 511 Lightning Table Saw 220V 3Phase. Has Motor Starter and Several Blades. Approximately 4.5" Maximum Depth Cut. J.A.FAY & EGAN Tilting Arbor Table Saw 16" Blade. Model: 511 Lightning. Excellent Working Condition. 220V 3Phase. Has Motor Starter and Several Blades. Approximately 4.5" Maximum Depth C FAY & EGAN Tilting Arbor Table Saw 16" Blade. Model: 511 Lightning. Excellent Working Condition. 220V 3Phase. Has Motor Starter and Several Blades. Approximately 4.5" Maximum Depth Cut J.A.FAY & EGAN Tilting Arbor Table Saw 16" Blade. Model: 511 Lightning. Excellent Working Condition. 220V 3Phase. Has Motor Starter and Several Blades. Approximately 4.5" Maximum Depth Cut J.A.FAY & EGAN Tilting Arbor Table Saw 16" Blade. Model: 511 Lightning. Excellent Working Condition. 220V 3Phase. Has Motor Starter and Several Blades. Approximately 4.5" Maximum Depth CutJ.A.FAY & E

FELDER FORMAT 4 CREATOR 950 CNC MACHINING CENTER (W/BORING/ROUTING/ATC/DOWEL INSERTING): Specifications: • Main spindle 12 kW (16 HP) variable speed from 1,500 - 24,000 RPM, (S6) HSK F63• Drill head DH17 6H 1S; 3 HP (2.2 kW) Motor, variable speed from 4,500 - 8,000 RPM.• 11 vertical spindles - 6 horizontal spindles - 1 slotting saw in X• Four-side formatting possible as standard• Length measurement of the workpiece in X and Y• 4 position tool changer for use of aggregates• Controlled centralized extraction connection• Automatic central lubrication systemPositioning Speed:• Panel feeding speed (Y-axis) 229 FPM (70 MPM), X-axis at 229 FPM (70 MPM), Z-axis at 65 FPM (20 MPM). Axes positioning by AC drives & brushless Servo motors. The Panel moves in Y-axis & the boring head moves in X & Z-axes.Work Area:• NC Controlled "Optical Laser Sensor" creates a zero-panel reference point by reading the panel's ends; this ensures that RH & LH (mirror image) panels will always be symmetrical. High precision clamping automatically positions the workpiece. Automatic presser moves independently and adjusts to workpiece thickness. Pneumatic side pusher makes locating workpiece accurate and efficient. LH Side pressure clamp with automatic adjustment & pneumatic locking according to the panel width. Scratch resistant rollerball table makes for ease of loading parts into the machine.Operator Interface: • PC-Based user-friendly icon driven Control housed on the main machine base + "WOODFLASH" Operating System. 19' LCD Displays programming graphics, functions, machine data. Options Include:•Mobile Dowel Inserting unit as pictured.• Actual model is: FELDER FORMAT 4 CREATOR 950