Woodworking Equipment For Sale

SICOTTE - J 3H-7, ...Vertical Boring Machine24" x 84" Table size. Equipped with: -- (5) 1.5 HP Motors mounted on 24" long arms with motor starter and overload relay. -- (5) 1-1/2" Dia. spindles with spring collet 1/2" capacity. -- (2) Spring loaded holddowns.Features: -- 0" - 8" Vertical table feed, hydraulically operated; variable feed and table travel adjustable from front of machine. -- 3 HP Hydraulic pump motor with reservoir. Complete with: -- Electrical Control System with separate motor controls. -- Single or continuous stroke. -- Manual and automatic cycle. -- Foot pedal actuation. -- (1) Safety guard.

SICOTTE J3H-A-6 Angular Vertical Boring Machine24" x 72" Table size Angular boring machine for chair seat -- (6) Hydraulic self feed spindle having 3 7/8" adjustable stroke and variable speed feed, 1 HP motor, jacob chuck 0 to 1/2" capacity, mounted on 24"long arms with timing belt drive. -- The spindle can be set at coumpônd angle angle with 30 deg front to back and 15 deg right top left. -- (2) Air holddowns. -- 0" - 8" Vertical table feed hydraulically operated that can be used when you drill vetically without angle, , variable feed and table travel adjustable from front of machine, -- 3 HP hydraulic pump motor with reservoir. Complete with: -- Electrical control system with separate motor controls, -- Single or continous stroke, -- Manual and automatic cycle and foot pedal actuation, -- Selector switch to activate each spindle manually . -- This machine is design for chair seat boring or any other application where angular holes are required.

SICOTTE - T 1050, ...Horizontal Boring Machine 2-Spindle Horizontal Borer.Equipped with: -- 1 HP Motor, timing belt drives with motor starter. -- (2) Horizontal spindles, 2" dia. with Jacobs® Chuck, 0 - 1/2" capacity, turning at 3,450 RPM.Features: -- 4" Boring head stroke with air/oil system and adjustable feed speed. -- Spindle mount on dovetail beam with min. 2" to a max. 11-3/4" center distance.Complete with: -- (2) Pneumatic hold-downs & 12" x 16" wooden table size.

Model SF-45A 600 V / 3 Ph / 60 Hz 10ft table 8.5 HP main motor provides(2) cutting speeds 3,800 & 5,200 RPM

SILVER 6023AH Moulder Feed Through 6-Head (B-R-L-T-T-B), working cap. 9-1/16" x 6". Head sequence: -- Bottom 10 HP, top 10 HP, right 10 HP, left 10 HP, top 15 HP, top 15 HP and bottom 15 HP motor. -- Spindle dia. 40 mm with cutterhead speed of 6,000 RPM. -- All spindles with mechanical digital readouts. -- Feed: Variable speed of 18 - 82 FPM, with 5 HP feed drive motor. Powered feed rollers top and bottom. -- Infeed: Straightening table 2 M (6'6"), with side pressure roller and table lubrication pump. Includes:: -- Centralized control panel, -- Sound and safety enclosure.

SILVER SJK-19T Line Boring MachineSingle line vertical boring machine with (19) spindles at 32 mm centers driven through a powerful 1.5 HP motor.Equipped with: -- Foot pedal controlled pneumatic boring cycle -- Adjustable boring feed speed -- Adjustable boring depth for fast changeover -- 2 Pneumatic cylinder clamp for solid hold-down to the material. -- 3 Meter long back fence for long line boring with flip stops -- (2) Positioning pins at both end of boring head to set up for longer line boring quickly -- Quick change chuck for fast changeover (19 pcs included)Specifications: -- No. of Spindles....................................................................................... 19 -- Distance between each spindle.............................................................. 32 mm -- Max Boring Depth .................................................................................. 60 mm (2.36") -- Working Table Size................................................................................ 800 x 500 mm (31.5" X 19.68") -- Table Height from Floor......................................................................... 780 mm (30.35") -- Max Boring Depth from Edge................................................................. 155 mm (6") -- Electric .................................................................................................. 220 V / 60 Cy / 3-Ph -- Machine Size (LxWxH) ........................................................................... 920 X 670 X 1490 mm (36.25" x 26.37" X 58.66") -- Net Weight ............................................................................................ 220 kgs. (484 Lbs)

SILVER SJK-21 Horizontal & Vertical Boring on 32 mm centers.(21) Spindles in line on one boring head (aluminum alloy single block), drills vertically from top & horizontally from rear. -- Features pneumatic adjustment for horizontal boring.Specifications: -- Max drill dia. is 1.38" (35 mm); Max panel thickness is 2.36" (60 mm); Table size 36" x 19.75" (914 x 502 mm). -- Length of cross fence is 102" (2,600 mm); length of aluminum table fences are 39" (1,000 mm) to the left and 28" (710 mm) to the right with flip stops.Equipped with: -- Depth stop adjustment, (2) holddown air cylinders, and foot pedal operation for clamping/drilling cycle. -- 2 HP - 3,600 RPM TEFC motor with thermal overload protection and low voltage controls.. -- Includes (12) Quick change chucks..

SILVER - SJK-65: Construction & Line Boring Machine(4) Vertical Boring Heads; 21-spindle from bottom on 32 mm centers; (1) Horizontal Boring Head; (21) spindles on 32 mm center. -- 3" (75 mm) Max. drilling depth; (3) 4.0 HP - 3,450 RPM motors; pneumatic-hydraulic drill head advance with: Speed control with working speed or (0 - 15) cycles per min.; head height adjustment with: Mechanical digital readout; 51" x 37" working capacity. -- Equipped with: (2) Pneumatic holddown clamps; pneumatic foot pedal control.

Silver Straight Line Rip Saw 15 HP Motor

SIMI 5' x 10' HOT PRESS Platen dimension 123" x 63" (3,125 mm x 1,600 mm). -- Max. daylight opening 17" (430 mm). -- (8) Hydraulic upstroke cylinders with diam. 6" (150 mm). -- Electrically heated platens with a maximum heating temperature of 240 F (120° C) -- Loading on all (4) sides of press.Overall dimensions: Length 165" x 81" x 117-1/4"

Simonds Band saw leveler. Comes with pallet of spare parts.

SNX - Coil Hub, ...Edgebanding Heater & Storage System: For straight-line and contour Edgebanders - Keeps banding at the perfect temperature. - Softens banding, making it more pliable. - Keeps banding at the perfect temperature. - Softens banding, making it more pliable. - Increases adhesion. - Decreases delamination issues. - Allows a cleaner guillotine cut. - Lessens the chance of chipping when trimming. This "CoilHub" also keeps the coils contamination-free, keeps the edgebanding easily accessible right at the machine, and can store up to (20) coils.

SNX nVISION SYSTEM G1 SEMI-AUTOMATIC CONTOUR EDGEBANDER: -- Specifications: Curved (Contour) Edgebander to allow 360° edgebanding to contoured (shaped) panels.Edgebanding is applied automatically as part is advanced past the edgebanding workstations via turntable.Reduced learning curve/expertise for operation as operator simply loads part to vacuum turntable, then activates the edgebanding cycle. -- Working Capacity: The nVision 1 can band Minimum material size 150 mm (6") diameter.Maximum material size 2,400 x 2,400 mm (94" x 94"); Maximum material weight up to 104.5 KG (230 lbs).Material thickness from 10 - 60 mm (0.4" - 2.36"); Banding thickness from 0.5 mm thin tape w/low temp adhesive - 3mm tape. -- Radii Capacity:Minimum Internal (inside) radius 80 mm (3.14"); minimum external (outside) radius 30 mm (1.18") based on 1 mm thick edge tape. Edgebanding thickness 1 mm, min = R 30 mm Edge thickness 2 mm, min = R 50 mm Edge thickness 3 mm, min = R 80 mm Panel thickness 10-60 mm with edge thickness 1 mm Panel thickness 10-60 mm with edge thickness 2 mm Panel thickness 10-45 mm with edge thickness 3 mmIMPORTANT: ALL minimum & maximum radii are affected by tape thickness, quality of adhesive and edgebanding being applied. Radius size dramatically affected by adhesive temperature and quality of edge tape; semi or rigid.Equipped with:Thermal-regulated glue pot heated via (2) 800 Watt heating elements with electronic temperature controls; holds up to 1 kG (2.2 Lbs) of granules. (2) Pressure rollers to copy the shape of the piece, automatic guillotine for coiled material up to 3 mm (0.11") thickness & 57 mm height (0.125" - 2.25"). Features: -- Laser for easy length identification with closed parts without the need for additional length measurement.The Laser also detects a tight radius and will automatically slow the speed + resume the set speed when the detected radius has passed.The machine is also equipped with the foot pedal for manual control/intervention. Motorized turntable for automated edgebanding application to large panels.Holding or support arm has a large inter-changeable vacuum pod to secure panels for edging and trimming.NOTE: Panels can be irregular in shape but must conform to the min. tolerances of inner & outer radii and fit within the work area.Complete with: Top & Bottom Trimming unit Centralized control panel with individual controls for all stations to enable manual feeding of panels if desired Banding station Edgeband coil stand Standard-size vacuum pod for articulated arm 80 mm dia. (3") dust extraction outlet Foot pedal activation/de-activation control Larger feed roller QC Glue tank with sensor. -- Actual Model is SNX nVISION SYSTEM G1

SNX NVISION SYSTEM2 CONTOUR EDGEBANDER: -- Specifications: Curved (Contour) Edgebander to allow 360° edgebanding to contoured (shaped) panels.Edgebanding is applied automatically as part is advanced past the edgebanding workstations via turntable.Reduced learning curve/expertise for operation as Operator simply loads part to vacuum turntable, then activates the edgebanding cycle. -- Working Capacity: The "nVision" Contour Bander can band a minimum material size of 150 mm (6") diameter.Max. material size of 2,400 x 2,400 mm (94" x 94"); max. material weight up to 104.5 kG (230 Lbs).Material thickness from 10 - 60 mm (0.4" - 2.36"); banding thickness from 0.5 mm thin tape w/low temp adhesive - 3 mm tape. -- Radii Capacity:Minimum internal (inside) radius of 80 mm (3.14"); minimum external (outside) radius of 30 mm (1'18") based on 1 mm thick edge tape. &#9679 Edgebanding thickness 1 mm, min = R 30 mm &#9679 Edge thickness 2 mm, min = R 50 mm &#9679 Edge thickness 3 mm, min = R 80 mm &#9679 Panel thickness 10-60 mm with edge thickness 1 mm &#9679 Panel thickness 10-60 mm with edge thickness 2 mm &#9679 Panel thickness 10-45 mm with edge thickness 3 mmIMPORTANT: ALL minimum & maximum radii are affected by tape thickness, quality of adhesive and edgebanding being applied. Radius size dramatically affected by adhesive temperature and quality of edge tape, semi or rigid. -- Equipped with:(1) NEW Thermal-regulated glue pot heated via (2) 800-Watt heating elements with electronic temperature controls; holds up to 1 KG (2.2 LBS) of granules. (2) Pressure rollers to copy the shape of the piece, automatic guillotine for coiled material up to 3 mm (0.11") thickness & 57 mm height (0.125" - 2.25"). -- Features: TRIAX 3-AXIS Laser System (patented) for tighter butt joints & easy length identification with closed parts without the need for additional length measurement.The Laser also detects a tight radius and will automatically slow the speed + resume the set speed when the detected radius has passed.The machine is also equipped with the foot pedal for manual control/intervention. Motorized turntable for automated edgebanding application to large panels.(2) "Heavy Duty" Articulating arms to support the parts during edgebanding and trimming & to maximize production throughput. Arm has a large inter-changeable vacuum pod to secure panels during edging and trimming. NOTE: Panels can be irregular in shape but must conform to the min. tolerances of inner & outer radii and fit within the work area. -- Complete with: &#9679 Top & Bottom Trimming unit &#9679 Centralized control panel with Simple PLC Touchscreen Interface with individual controls for all stations to enable manual feeding of panels if desired &#9679 Banding station &#9679 Edgeband coil stand &#9679 Standard-size vacuum pod for articulated arm &#9679 80 mm dia. (3") dust extraction outlet &#9679 Foot pedal activation/de-activation control &#9679 Larger feed roller &#9679 QC Glue tank with sensor.

SNX nVISION System2 G2 CONTOUR EDGEBANDER + Optional Dual Telescoping Arms for simultaneous Contour Banding & Trimming: -- Specifications: Curved (Contour) Edgebander to allow 360° edgebanding to contoured (shaped) panels.Edgebanding is applied automatically as part is advanced past the edgebanding workstations via turntable.Reduced learning curve/expertise for operation as operator simply loads part to vacuum turntable, then activates the edgebanding cycle. -- Working Capacity: The nVision Contour Bander can band a minimum material size of 150 mm (6") diameter.Maximum material size 2,400 x 2,400 mm (94" x 94"); Maximum material weight up to 104.5 KG (230 LBS).Material thickness from 10 - 60 mm (0.4" - 2.36"); Banding thickness from 0.5 mm thin tape w/low temp adhesive - 3mm tape. -- Radii Capacity:Minimum Internal (inside) radius 80 mm (3.14"); minimum external (outside) radius 30 mm (1'18") based on 1 mm thick edge tape. Edgebanding thickness 1 mm, min = R 30 mm Edge thickness 2 mm, min = R 50 mm Edge thickness 3 mm, min = R 80 mm Panel thickness 10-60 mm with edge thickness 1 mm Panel thickness 10-60 mm with edge thickness 2 mm Panel thickness 10-45 mm with edge thickness 3 mmIMPORTANT: ALL minimum & maximum radii are affected by tape thickness, quality of adhesive and edgebanding being applied. Radius size dramatically affected by adhesive temperature and quality of edge tape, semi or rigid. -- Equipped with:(1) Thermal-regulated glue pot heated via (2) 800-Watt heating elements with electronic temperature controls; holds up to 1 KG (2.2 LBS) of granules. (2) Pressure rollers to copy the shape of the piece, automatic guillotine for coiled material up to 3 mm (0.11") thickness & 57 mm height (0.125" - 2.25"). -- Features: TRIAX 3-AXIS Laser System (patented) for tighter butt joints & easy length identification with closed parts without the need for additional length measurement.The Laser also detects a tight radius and will automatically slow the speed + resume the set speed when the detected radius has passed.The machine is also equipped with the foot pedal for manual control/intervention. Motorized turntable for automated edgebanding application to large panels.(2) "Heavy Duty" Articulating arms to support the parts during edgebanding and trimming. Arm has a large inter-changeable vacuum pod to secure panels during edging and trimming.NOTE: Panels can be irregular in shape but must conform to the min. tolerances of inner & outer radii and fit within the work area. -- Complete with: Top & Bottom Trimming unit Centralized control panel with Simple PLC Touchscreen Interface with individual controls for all stations to enable manual feeding of panels if desired Banding station Edgeband coil stand Standard-size vacuum pod for articulated arm 80 mm dia. (3") dust extraction outlet Foot pedal activation/de-activation control Larger feed roller

SNX nVISION C 1.5 SEMI-AUTOMATIC CONTOUR EDGEBANDER: -- Specifications: The nVision C1.5 Curved (Contour) Edgebander to allow 360° edgebanding to contoured (shaped) panels. The Standard banding machine includes banding and trimming stations with one set of cutting tools, one articulated vacuum arm, an edgeband coil stand, and one 8″ aluminum vacuum pod. Includes on-site installation and training, free phone support, operation manual, and one-year limited warranty.The machine uses standard EVA hot melt glue and can apply .5mm to 3mm thick edgebanding.Edgebanding is applied automatically as the part is advanced past the edgebanding workstations via turntable.Reduced learning curve/expertise for operation as operator simply loads part to vacuum turntable, then activates the edgebanding cycle. -- Working Capacity: The nVision C 1.5 can band Minimum material size 150 mm (6") diameter.Maximum material size 2,400 x 2,400 mm (94" x 94"); Maximum material weight up to 104.5 KG (230 lbs).Material thickness from 10 - 60 mm (0.4" - 2.36"); Banding thickness from 0.5 mm thin tape w/low temp adhesive - 3mm tape. -- Radii Capacity:Minimum Internal (inside) radius 11.1 mm (0.4375 - 7/16"); minimum external (outside) radius 30 mm (1.18") based on 1 mm thick edge tape. IMPORTANT: ALL minimum & maximum radii are affected by tape thickness, quality of adhesive and edgebanding being applied. Radius size dramatically affected by adhesive temperature and quality of edge tape; semi or rigid.NOTE: Panels can be irregular in shape but must conform to the min. tolerances of inner & outer radii and fit within the work area.Equipped with:Thermal-regulated glue pot heated via (1) 800 Watt heating elements with electronic temperature controls; holds up to 1 kG (2.2 Lbs) of granules. (2) Pressure rollers to copy the shape of the piece, automatic guillotine for coiled material 0.5 mm - 3 mm (0.02" - 0.11") thickness & 57 mm height (2.25"). Operator Interface: -- Faster processor and a more accurate encoder for more consistent tight butt joints. 15"; touchscreen monitor. Training & Maintenance videos on PC. Connect to the internet for service and updates. More user-friendly interface. Bar code capable (optional).The 15"; touchscreen monitor provides an intuitive control panel, while features like training and maintenance videos make it easier than ever to maintain and operate the machine. The optional bar code capability allows for seamless integration into modern production workflows, reducing the potential for operator errors.Features: -- Tape height guide. Aluminum infeed guides. Solid shoe holder. Adjustable pod height spindle. Digital readouts. Pneumatic enclosure. Laser upgrade.The new PLC interface enhances usability, while the machine is capable of edgebanding and trimming an inside radius as small as 7/16″. It features 18,000rpm ER20 collet-type spindles (top/bottom) and the same proven articulating vacuum support arm. The nVision C1.5 can band and trim

SNX nVISION System2 G2 CONTOUR EDGEBANDER + Optional Dual Telescoping Arms for simultaneous Contour Banding & Trimming: -- Specifications: Curved (Contour) Edgebander to allow 360° edgebanding to contoured (shaped) panels.Edgebanding is applied automatically as part is advanced past the edgebanding workstations via turntable.Reduced learning curve/expertise for operation as operator simply loads part to vacuum turntable, then activates the edgebanding cycle. -- Working Capacity: The nVision Contour Bander can band a minimum material size of 150 mm (6") diameter.Maximum material size 2,400 x 2,400 mm (94" x 94"); Maximum material weight up to 104.5 KG (230 LBS).Material thickness from 10 - 60 mm (0.4" - 2.36"); Banding thickness from 0.5 mm thin tape w/low temp adhesive - 3mm tape. -- Radii Capacity:Minimum Internal (inside) radius 80 mm (3.14"); minimum external (outside) radius 30 mm (1'18") based on 1 mm thick edge tape. &#9679 Edgebanding thickness 1 mm, min = R 30 mm &#9679 Edge thickness 2 mm, min = R 50 mm &#9679 Edge thickness 3 mm, min = R 80 mm &#9679 Panel thickness 10-60 mm with edge thickness 1 mm &#9679 Panel thickness 10-60 mm with edge thickness 2 mm &#9679 Panel thickness 10-45 mm with edge thickness 3 mmIMPORTANT: ALL minimum & maximum radii are affected by tape thickness, quality of adhesive and edgebanding being applied. Radius size dramatically affected by adhesive temperature and quality of edge tape, semi or rigid. -- Equipped with:(1) Thermal-regulated glue pot heated via (2) 800-Watt heating elements with electronic temperature controls; holds up to 1 KG (2.2 LBS) of granules. (2) Pressure rollers to copy the shape of the piece, automatic guillotine for coiled material up to 3 mm (0.11") thickness & 57 mm height (0.125" - 2.25"). -- Features: TRIAX 3-AXIS Laser System (patented) for tighter butt joints & easy length identification with closed parts without the need for additional length measurement.The Laser also detects a tight radius and will automatically slow the speed + resume the set speed when the detected radius has passed.The machine is also equipped with the foot pedal for manual control/intervention. Motorized turntable for automated edgebanding application to large panels.(2) "Heavy Duty" Articulating arms to support the parts during edgebanding and trimming. Arm has a large inter-changeable vacuum pod to secure panels during edging and trimming.NOTE: Panels can be irregular in shape but must conform to the min. tolerances of inner & outer radii and fit within the work area. -- Complete with: &#9679 Top & Bottom Trimming unit &#9679 Centralized control panel with Simple PLC Touchscreen Interface with individual controls for all stations to enable manual feeding of panels if desired &#9679 Banding station &#9679 Edgeband coil stand &#9679 Standard-size vacuum pod for articulated arm &#9679 80 mm dia. (3") dust extraction outlet &#9679 Foot pedal activation/de-activation control &#9679 Larger feed roller

Combination Differential/Filling Machine SMARTCOATER with: 880 mm (34-1/2") Working/pass-through height; one of the best units ever produced. Dual purpose machine can be utilized as: -- 1) A standard differential Roll Coater for application of UV sealer or top coat material; as a differential Roll Coater the 1st application head is independently utilized to for precisely controlled application. -- 2) A Filling Machine for application of H2O or UV filling material to calibrate substrates with porous veneer; as a Filling Machine, both heads are utilized for application and reverse smoothing or pressing of UV filling material.Specifications: -- (2) Heads, 53" width cap. - 1st Head: 250 mm (9-3/4") Dia. rubber coated applicator roller with separate doctor roller; doctor blades are oscillating. -- 2nd Head: 245 mm (9-5/8") Dia. chromium coated smoothing/reverse roller w/separate chromium doctor roll; all heads are floating to compensate for calibration errors & minimize damages from oversize parts. -- Adjustable opening 0 - 100 mm (3-3/4"); thickness protection safety bar connected to pneumatic emergency lifting; EX-proof electrics on all motors. -- 2 HP Conveyor drive: Variable feed speed from 26 - 131 FPM; 1/2 HP variable RPM drive on doctor rolls and separate 3/4 HP drive on applicator & reverse rollers. -- Electrical power: 480 V, 3-Ph, 3.8 kW; 7 Amps.

SORBINI SMART COATER MF Single Head Differential Roll Coater;SORBINI - Single-Head Roll Coater, ... "SMARTCOATER MF" SeriesMachine Features & Benefits:Single-Head Roll Coater designed for smooth application.Conveyor belt made of: Solvent resistant material with automatic tracking rollers mounted underneath the application rollers (182 mm dia.).Application rollers (250 mm dia.) covered with Heavy Duty vulcanized rubber of different shore hardness for different applications & coating products.Heavy gauge chromed steel doctor rollers (173 mm dia.).Feeding belt, coating rollers, and doctor rollers are all driven by independent motors and inverter is controlled directly from the control panel.Self-leveling floating head for optimum application on uneven surfaces.Thickness control and indicator on the control panel.Different types of scrapers are available according to the coating product and type of application.Pneumatic pump for lacquer feeding and recirculation.Differential capability allows for rotation inversion of doctor rollers and for fine adjustment of the applied coating, particularly important for high quality top coats.Safety "Cleaning Mode" to facilitate and safely service the machine.Technical Specifications:Working width from 0 to 1,300 mm (0 to 51 in).Min. workpiece length: 305 mm (12 in).Speed range: 2 - 11 MPM (6-1/2 to 36 FPM).Power consumption: 4 kW.Compressed air required: 15 Nl/Min (0.53 CFM) exhausted solvent/air mix. Working side: Right.Electric equipment: Explosion proof.Footprint Dimensions: Length 898 mm (35 in.) width 3,282 mm (129 in.) height 1,674 mm (66 in.).

CEFLA/SORBINI, VS 34/ACT/1600 - Top Only Panel cleaning machineEquipped with:One (2) Anti-Static ionization bar. One (2) soft horse hair brush, in opposite rotation to panels feed direction, 400 RPM brush speed.One (2) timed, compressed air blower Min. work piece length 290 mm (11.5";).Belt conveyor with variable speed feed from 3 - 16 MPM (approx 10 - 52 FPM). Hand wheel for thickness adjustment.