Woodworking Equipment For Sale

Craftsman Drill Press

CRAFTSMAN DP-65 Drill PressSpecifications: -- Capacity: 15" -- Motor: 0.33 HP Equipped with: -- Push button control -- Stand

This item is in an Auction on exfactoryauctions.com. Go here to view item: http://exf.ac/i6k ROCKWELL/CRESCENT 5-Head Single Head Tenoner Equipped with: Manually-operated sliding table. (1) Top & (1) Bottom Tenon Heads, Each with 2 HP Motor, (1) Top & (1) Bottom Cope Heads, Each with 1 HP Motor, & (1) 7" Cutoff head with 1 HP Motor.

CRESCENT P 24 PLANER -- 24" x 8" Cap., 10 HP direct drive motor. -- 4-Knife cutterhead, approx. 11" min. un butted stock length. -- 24" x 36" (Approx.) Cast iron table, manual raise-and-lower. -- 1 HP Separate feed motor, variable speed from 20 - 50 FPM; (2) 3-5/8" dia. powered bed rollers, (1) 3-5/8" dia. upper outfeed roll, and sectional infeed roll with (12) 2" sections. -- Features: Sectional chipbreaker with (12) 2" sections.

?Cresswood EF-60 Grinder 100 HP 60” Wide Feed Opening Includes 60”W Vibrating Conveyor (shaker table)

CROUCH - 81-70 ...Edge Sander (Non-Oscillating)5 HP Direct drive motor; 6" x 144" abrasive belt size; (1) 8" x 56" Platen.Equipped with: -- (1) 12" x 56" Adjustable side table and (1) 15" x 28" end table.Tables adjust vertically 5" and laterally 2-1/2". -- 8" Dia. rubber covered drive pulley and 4" dia. aluminum idle pulley.

CROUCH - 250-F, ...Edge Sander37" x 6" Graphite coated platen; 2 HP motor. -- Equipped with: 9" x 36" Side table with adjustment; 10" x 32" end adjustable table.

Each system is custom built to fit your specifications. Standard Electric Lateral Chain Feeders include Basic Feeder with transport length of 30" Workpiece width 3/4" - 9-1/4" Min. Workpiece length 12" Drive system with 4 HP total drive system Feed speed range 50 - 250 ft/min (up to 400ft/min available) Thickness 1/4" - 4" Steel flat top chain 60 Cycle per minute Adjustable Fence 35MM Feed Wheel Shafts Options 6'-16' Lateral Chain Feeder Feed Wheel Knurled, Urethane or Light Knurl Hub Options 3/4" or 2" Powder Coating Bridge Side Fence Feed Speeds up to 400 FPM Short Stock Fence 12" Wide Capacty

11' Infeed Rollcase for Planer

S.A. Wood Pineapple Feed Rollcase Serial# 46589-2

PHL (Comact) Fabricated Planer-Matcher, model P612, 6 roll planer with 16 knives. Independent electric drives are missing. Removed from service in 2023. Many spare parts. Supported by Comact who acquired PHL.

OWNER IS RETIRING! Sliding Gravity Roll Case for Straight Line Rip Saw, Special Design w/ air stop brakes, (2) steel overhead mounts and one laser light, Excellent for Precision Edging. Seller will load on your truck. (ref #74) Call Rachel for more information 931-797-6284

Orbital Sander Line 2004 DMC Unisand 2000 Timesavers Model 252-4C

DMCTC 1350-M2-RP Orbital Sander (2) Heads --53" Width cap. Drum, Combination Head --Head Configuration --1st Head:10" Dia. helical grooved rubber covered calibrating roller, 26 kw (34 HP) motor. --2nd Head: Rubber covered contact roller with finishing platen 18 kw ( 28.5 HP) motor. --Specifications --Working width 1350 mm --Max thickness 170 mm --Belt size both heads 1370 mm X 2620 mm --Feed speeds variable from 3.5 -18 m/min. Feed motor 2.2 kw ( 3 HP) motor --Equipped With --Electronic sanding belt oscillation --Exhaust hoods with 4 outlets --Motor safety switch for main motor --Power rise and fall --Panel cleaning brush --Sander dim. L 2600 mm X W 2400 mm X H 2550 mm --Weight 2900 kg. --There is a crack in the plastic housing but it does not affect the functionality of the machine.

DMC - EuroSystem SY-TC 1350, ...Heavy-Duty 4-Head Wide Belt Sander53" Width cap. Drum, Drum, and Drum; Segmented Platen.Specification; -- Max. workpiece width: 53". -- Workpiece thickness: 0.32" - 6.8".Head Configuration & Feed: -- 1st Sanding Unit: 10"; Diameter grooved steel contact drum; 60 HP motor. -- 2nd Sanding Unit: 10"; Grooved rubber covered drum, 27 HP motor. -- 3rd Sanding Unit: 10"; Grooved rubber covered drum; 20 HP Motor. -- 4th Sanding Unit: Electronic segmented platen; 35 HP motor. -- Belt size of 53" x 103". -- Feed Motor: 5 HP, Variable feed speed. -- Vacuum Bed. -- Constant Pass Line.Equipped with & Features: -- Power Panel Touchscreen Control. -- Shoe type holddowns. -- Amp meters for all Sanding Units.

DMC - 1350 RK, ...TECHNOSAND Dual Head Wide Belt Sander.(2) Heads, 52" width cap. - Head sequence: Contact sanding roll and Segmented platen. Head Configuration:1st Head: 7" (175 mm) Dia., 85 durometer rubber-covered calibrating contact sanding roll.2nd Head: Segmented finishing platen with EPICS (sectional electronic pad) with (46) electronically controlled air segments.Specifications: -- 53" x 103" Long abrasive belts with electronic tracking on all wide belt heads. -- Turbo panel blowers, timed abrasive belt air cleaners. -- DMC "Hydra 35" control, "EPICS" control for sectional platens. -- (99) Programs; graphic screen for machine configuration, +/- control on segmented platens, abrasive belt cleaners. -- Sequential automatic start-up, machine troubleshooting and self-diagnosis. -- Variable feed speed from 15 - 60 FPM (4.5 - 18 MPM), 1.5 HP feed drive, vacuum conveyor bed with 7.5 HP suction fan and motor.Equipped with & Features: -- Automatic conveyor belt tracking, infeed & outfeed holddown pinch rolls or shoes on all heads. -- 0" - 4" Motorized programmable thickness adjustment with LED readout. -- Automatic part thickness adjustment, infeed hand safety stop, outfeed emergency stop. -- Motor load meters and control console with monitor & keypad.NOTE: Message from the Seller: The machine was setup by a DMC tech. It has a new calibration roller & new bearings, rebuilt HYDRA 35 controller; currently under power, comes with dust collecting manifold and hoses, plus the machine can be loaded onto a flatbed for ...$ 600.

DMC UNISAND K (3) Bottom and (3)Top heads wide belt sander. --, 43" max. width. - Bottom Head sequence : 1st Head Contact roll, approx.18.5 KW motor- 2nd Bottom Head Contact roll, 2rd Bottom head, Combination head with roll and platen , approx.15 KW 2-speed motor, belt speed 118 m/sec. -- Bottom panel brush. -- Top Heads: 1st Top Head: Rubber covered contact roll approx. 18.5 KW motor, 2 speed, belt speed 9/18 M/Sec. adjustable contact roll with pneumatic grit adjustment. 2nd and 3rd Top Head: Combination head with Rubber covered contact roll and polishing platen, approx. 18.5 KW HP motor, adjustable contact roll with pneumatic grit adjustment.Top panel brush. -- 44"x 103" abrasive belts with electronic tracking; computer controlled set-up functions with key pad and LCD screen. -- Vacuum Conveyor feed belt with variable feed speed from 11 - 60 FPM, approx. 7.5 KW HP feed drive, automatic conveyor belt tensioning & tracking. -- Infeed & outfeed holddown pinch rolls on all heads, motorized part thickness opening with LED readout, 1/8" - 4" max opening, automatic part thickness set-up sensor. -- Complete with: Infeed safety stop, outfeed emergency stop, motor load meters, high efficiency dust extraction and control console with monitor. -- Actual model USK1350-IM3 + USK1350

DMC - TC1100 1M3, ...6-Head Top & Bottom Sander(3) Heads bottom and (3) heads top; 1,100 mm (43") max. width. Head Sequence for Each Top and Bottom Machine -- 1st Head: Rubber-covered contact roll, 30 kW (40 HP) motor. -- 2nd Head: Rubber covered contact roll, 22 kW (30 HP) motor. -- 3rd Head: Finishing platen, 14 kW (19 HP) motor. -- 4th Head: Cleaning brush, 0.9 kW (1.2 HP) motor. -- Extra-long feed belt of 43" x 102"; long abrasive belt with electronic tracking. -- Variable feed speed from 11 - 60 FPM; 1/8" - 4" motorized part thickness opening with LED readout. -- 43" Wide Vacuum feed belt. -- (2) Vacuum blowers with 12 HP motor. -- Separate controls for each machine (in same control cabinet).

DMC - UNISAND 2000-M2, ...Wide Belt Sander (2) Heads -- 53" Width cap. Drum, Platen.Head Configuration: --1st Head: 11" dia. (300 mm) Rubber-Covered Contac; (2) speeds or inverter adjustable 20 - 25 HP; Varied RPM. --2nd Head: Combination head with drum and graphite covered 2-1/2" finishing platen; 25 HP.Specifications: -- 54"x 103" Abrasive belts with electronic tracking. -- Shoe & Roller Holddowns. -- "Hydra 35" Computor controlled; set-up functions with keypad and LCD screen. -- Conveyor belt feed with variable feed speed from 11 - 60 FPM; 6.4 HP feed drive. -- Vacuum conveyor bed with: 7.5 HP Motor and suction fan. -- Automatic conveyor belt tensioning & tracking. -- Motorized part thickness opening with: LED Readout; 1/8" - 4" max. opening; automatic part thickness set-up sensor. Equipped with & Features: -- Infeed safety stop, outfeed emergency stop, motor load meters.2-Roll infeed conveyor extension; high efficiency dust extraction.

D M C - UNISAND 135, ...3-Head Wide Belt Veneer & Finishing Sander. -- General Data:3-Head, 51" (1,300 mm) nominal width cap.; motorized part thickness opening with LED readout; 1/8" to 4" max. - Head sequence: Cross belt, rubber-covered Drum, Pad. Head Configuration/Specs: -- 1st Head: Cross belt with: EPICS 44 Segmented electronically controlled air platen; 2-speed abrasive belt; approx. 36/72 FPM (11/22 MPS) linear speed; driven by 19 & 24 HP motors; 6" wide x 238" (6,050 mm) long abrasive belt. Inside synchronized Chevron belt, approx. 228" (5,800 mm) long.Pad unit with pneumatic cylinders: Each acting on a high absorption felt strip; working pressure controlled via control panel. HYDRA Belt: 2' Electronic control with oscillating blower for cleaning. -- 2nd Head: Rubber-covered 45-durometer steel roll, 9.8" (250 mm) dia. with: 18 HP 2-speed motor, 52" x 103" (4,055 mm) long oscillating abrasive belt with electronic tracking; air blast abrasive belt cleaner. Belt runs approx. 3,550 FPM (18 MPS) linear speed; adjustment & indicator of working position. -- 3rd Head: Flexible Sanding Platen with: EPICS 44 Segmented electronically controlled air platens; 3-speed 24 HP motors; 52" x 103" (4,055 MM) long abrasive oscillating belt with electronic tracking, timed oscillating air blast abrasive belt cleaner.Pad unit composed of: Pneumatic cylinders, each acting on a high absorption felt strip. Working pressure controlled vial control panel. Special rails allowing a quick change of graphite cloth on pad. Interchangeable system to modify the hardness, stiffness, and profile of the contact surface. Controller: -- DMC "HYDRA 30" Upgraded computer with: Working position display modes mounted in a separate control cabinet; automatic thickness device reads and adjusts feet table height, motor load meters. Transport Belt Drive: -- Variable feed speed of 16 to 82 FPM, conveyor feed drive, infeed & outfeed holddown pinch rolls on all heads; infeed hand safety stop, outfeed emergency stop; high efficiency dust extraction and separate control console with monitor, keypad, etc. Also included: -- Cleaning brush head at machine discharge. -- High pressure vacuum blower. -- Dust manifold. -- Extended outfeed table.