Gang Rip Saws For Sale

Ripsaw Feeder with 32" wide feed rolls on 18" thru 28" roll centers; will feed 3' thru 16' lumber. With 24" of in-out fence travel; feed speeds from 50 to 150 FPM; 3/4 HP feed roll drive and 3/4 HP fence drive via gear motor with brake. -- Fabricated frame of structural steel with boots that allow +/- 1" elevation adjustment. 3-1/2" dia. steel feed rolls driven by a variable frequency drive for speed adjustment; rolls are canted to aid in holding stock against the fence. -- Powered fence with 24" fence travel is easily shifted via joystick control for stock alignment with the sawblades. -- With pneumatic powered gate to keep material from feeding until the operator initiates the feed sequence. -- Urethane covered idler pinch roll is attached to the fence and is powered down at the start of the feed sequence. When a photocell detects the board is clear of the gate, the pinch roll and gate will return to their normal position. Electrical control panel ready for connection to the power supply.

ROSE MACHINERY HBR Horizontal Band RE-RIP SawThe Horizontal Band Re-Rip Saw is an effective and efficient means of ripping short blocks into as many as six (6) set rip widths. Rip widths are easily adjustable, as well as the setting for stock thickness.Advantages of the system: -- Compact, efficient use of floor space. -- Accurate cutting of rips with minimum tear-out. -- Short blocks, 4" minimum length, without taper problems. -- Straight through feed design, good for sorting. -- Minimum dust collection required. -- Single point scrap collection. -- One saw drive motor, requires less power. -- Safety, no kickback problems.Specifications: -- Five (5) rip widths - (6) optional -- 20 HP bandsaw drive -- 30" diameter band wheels, 2" wide face -- (2) 3/4 HP feed works drives -- 1-1/2 HP feed belt drive -- 1" to 6" rip width (independently adjustable in each lane) -- 10" maximum board width at maximum rip -- 4" maximum waste piece width -- 3/4" to 2" stock thickness (all lanes adjust together) -- 4" minimum stock length -- 36" maximum stock length -- 80 FPM feed speed -- 52" to 58" pass line height -- Motor starters and push buttons included, wired for 440 volt, 3 phase, 60 Hz (uses standard mag starters) -- An automatic band lubrication system is includedOptional Equipment: -- For SIX (6) LANES, add ...$5,600 (SORTER increases $3,700) -- Automatic machine grease lubrication system, add ...$ 9,200 -- Ergonomic overhead stock slide, add ...$ 5,600 -- Output conveyor and sorter for 5-LANEsingle side discharge, add ...$47,300 -- Output conveyor and sorter for 6-LANE single side discharge, add ...$51,100 -- Operator's platform, add ...$ 7,900 -- Optional voltage configuration: 220/380/440V, 50HZ, add ...$2,900 -- Start-up and training, add $1,000 per day plus expenses at costHorsepower Requirements: -- (1) @ 20 HP -- (1) @ 1-1/2 HP -- (2) @ 3/4 HPDust Collection: -- (2) outlets, 6" diameter, 5,200 FPM velocity @ 2,300 CFMCompressed Air Required: -- 90 PSI @ 1.4 CFM

ZHW800-70- SMW Gang Rip Saw - Saw from 3/8"-2 3/4"T x 31 1/2"W, 11"dia Saw Blade, 1-10 Blades, 29hp Motor. Also Available: ZHW800-80- SMW Gang Rip Saw - Saw from 3/8"-3 1/4"T x 31 1/2"W, 12"dia Saw Blade, 1-10 Blades, 40hp Motor. ZHW800-100- SMW Gang Rip Saw - Saw from 3/4"-4"T x 31 1/2"W, 14"dia Saw Blade, 1-10 Blades, 49hp Motor.

SCM M3 Multi-Blade Dip Chain Gang Rip SawSpecifications: -- 300 mm (11.81") Width cap. -- 110 mm (4.33") Max. depth of cut. -- 8-3/4" Throat depth. -- 390 mm (15.35") Min. stock length. -- 200 - 350 mm (7.87" - 13.78") Blade diameter. -- Arbor dia. 70 mm (2.76"). -- Table size 750 x 1,530 x 750 mm H (29-1/2" x 60.24" x 29-1/2" H). -- Blade speed 4,200 RPM. -- Feed speeds 6 - 48 MPM (19 - 157 FPM).Equipped with: -- 44 kW (60 HP) - 3,554 RPM Blade motor. -- Variable speed drive feed chain motor. (2) Upper infeed & (2) Upper outfeed 4" Dia. rollers, Automatic chain lubrication. -- Top & bottom anti-kickback fingers. -- Main dust hood, with 200 mm (7.87") Dia. outlet. -- 40"; x 2-3/4"; H Adjustable infeed fence. -- Motor load meter.Complete with: -- Operation & Maintenance Manual. -- Tooling (As pictured).

SCMI M3 Gang Rip Saw Includes: Misc blades

SCMI Beam Saw was functioning well when taken out 12 years ago, scoring saw, and some blades. Needs to go $3,500. 713-304-8544

SCMI M3 Rip Saw Still under power for inspection

Dip Chain Multi Saw Believed to be a SCMI 2 extra arbors Extra blades

SCMI Gang Rip Saw S/N B.540480

Shurman Double Arbor Gang Saw 12" Capacity Thin Kerf Babbit Grinder

It is a 2 saw re-rip with one moveable saw and an adjustable fence. Capacities: Minimum length = 8” Maximum length = 192” Minimum width = 1 ½” Maximum width = 6” Minimum thickness = 7/8” Maximum thickness = 1”

Multirip circular saw for block cutting, with reinforced structure and high production speed. Trailed top and bottom rollers, upper rollers with adjustment, shafts with cartridge system for quicker and more efficient replacement of the set of saws, U-beam base with levelers and central lubrication. It does not come with the circular saws. - Maximum inlet width: 600 mm; - Minimum inlet height: 70 mm; - Maximum inlet height: 160 mm; - Double arbor: Ø 80 mm; - Number of saws per axle: 10x; - Exterior saws Ø: 350 mm interior saws - Ø: 110 mm; - Upper press rollers: 2x; - Bottom rollers: 6x; - Max. Feed speed: 35 m L / min for logs - 160mm above in diameter; - Max. Feed speed: 40-50 m L / min - only for logs 130-160mm in diameter; - Lower main motor indicated: 200 hp 2p (1x) Included; - Top main motor indicated: 150 hp - Main motor belt: 4 / 3v (8 Pcs); - Motor traction of the rollers: 5 cv 4p; - Gearmotor: GS (crown and pinion); - Length: 3366 mm; - Width: 2782 mm; - Height: 2233 mm; - Approximate weight: 5.470 kg

Viking Splitter Sizing Line with Operator Platform

WINTERSTEIGER - DSG 150 ECO, ...Thin Cutting Frame SawSide & Center Guides: Fitted as standard on the basic machine to guarantee the broadest possible range of application. Specifications: -- 11 kW (15 HP) Main motor; 0.3 - 1.5 MPM feed speeds; 210 mm saw frame stroke with (450) strokes/Min. -- 30 - 216 mm Cutting height, adjustable as required; max. +/- 0.5 mm difference in block height. -- 60 - 150 mm Cutting width (side guide); (2) 23 - 70 mm cutting width (using center guide); (2) channels max. 72.5 mm using 7.5 mm guide or with (5) channels max 24.5 mm using variable block width; 300 mm min. block length. -- 1.5 mm Cutting accuracy; +/- 0.2 mm Cutting loss (depending on saw length). -- Max. (30) saw blades (excluding scraper saws); (3) 120 mm sawdust extraction tubes. -- "Air Jet" Module: Cleans the lamellas and saw blades during the sawing process by blowing away the sawdust; cools down the saw blades during the sawing process and cleans the shaving space of the saw blades. -- "Air Jet" also increases the saw blades life and improves the lamella's accuracy. Sawdust-free lamellas can then be glued immediately after cutting.Comes with transformer

Wintersteiger DSG Sonic Frame Saw