Woodworking Equipment For Sale

SCM OLIMPIC K208ER EDGEBANDER WITH CORNER ROUNDING15/32" (12 mm) Max. edge cap., 2" max. (w/corner rounding only 1-3/4") banding height, 2-3/8" min. panel width and 6-5/16" min. length.Equipped with: -- Automatic strip & coil feed magazine w/Heavy Duty 3 mm PVC cap. guillotine. -- Teflon coated glue pot with glue roller application system complete w/automatic recycling device for unused glue. -- Digital thermostat adjustment for temperature control. -- 3-roll pressure unit w/pneumatic controls for all pressure rollers.Workstations: -- Double motor front & rear end trim (0.4 HP - 12,000 RPM motor ea.), tilts 0° - 15°, end trimmers mounted on 45° THK guide. -- Top & bottom fine/radius trimmer w/pneumatic positioning from control panel. -- Corner rounding units for leading & trailing edges. (2) 0.5 HP - 200 Cy Motors ea. -- Top & bottom PVC scraper for up to 5 mm radius. -- Top & bottom buffing unit (0.33 HP - 2,800 RPM motors). -- Hot air heating unit for PVC/ABS. -- Single 42 FPM fixed feed speed, 1 HP drive; heavy 3/4" drive chain with chain pads traveling on round & flat tracks.Complete with: -- Microprocessor for line control & glue temperature (can store up to 50 preset programs), swiveling control panel, pneumatic positioning of super finish, full cover sound enclosure, 200 Cy - 5 kW frequency inverter w/automatic motor brakes for all HF motors; includes used tooling. NOTE: Video of equipment was made in February 2021, prior to being decommissioned and placed in storage fully wrapped and ready for transport.

SCM - OLIMPIC K 201 HFA, ...Automatic Compact Edgebander with: 3 mm Max. coiled edgebanding thickness & High Frequency motorsSpecifications: -- Edgebanding thickness cap. (for both coil & strip): 0.4 - 3 mm (0.02" - 0.19"). -- Min. panel length for coiled edges (min. width 200 mm) 140 mm (5.51"). -- Min. panel width for coiled edges: 65 mm (2.56"). -- Panel thickness: 8 - 40 mm (0.31" - 1.57"). -- Feed speed:9 MPM (29 FPM).Equipped with: -- Automatic adjustment of all units when panel thickness is changed. -- 20" Dia. coil table. -- Automatic coil feed magazine; manual strip feed. -- Teflon-coated glue pot. -- 1.2 mm (0.05") Cap. guillotine. -- Eye-level control with: GEFRAN "1000" LED Temperature controller. -- Adjustable feet.Workstations: -- Single-motor end trimming unit with: (1) 0.19 kW (1/4 HP) - 12,000 RPM High-frequency motor & copying device. -- Top & bottom flush trimming unit with: (2) 0.35 kW (1/2 HP) - 12,000 RPM high-frequency motors, and front & vertical copying devices.

SCMI OLIMPIC K 560 T-ER2 EDGEBANDER (W/PRE-MILLING & CORNER ROUNDING) Specifications: -- Edge Capacity, 0.4 to 6 mm (0.016 to 0.25") for strip feeding. -- Panel Capacity: Min. Panel width 60 mm (2.375"); Min Panel length 140 mm (5.5");Min./max. Panel thickness 8 - 54 mm (0.375" - 2.125"); Minimum distance between panels 600 mm (24").Equipped With: -- Pre-milling station: (2) 2.0 HP (1.5 kW) motors, to rectify/clean panels already sized. -- Adjustable In-feed Fence: Manually pre-set with digital indicator, pneumatic in/out positioning. -- Automatic Strip & Coil Feed Magazine: For straight edges and 3 mm guillotine for coils. -- Gluing Station: For EVA (Hot Melt) with Quick change/disconnect Teflon glue pot for fast glue tanks change if needed. Heat-up time approx. 10 Min. -- Pressure Section: Manual digital positioning; Teflon coated pneumatic driven roller & (2) spring loaded idle rollersWorkstations: -- End Trimming Station: Front & rear 2 x 0.5 HP, 12,000 RPM motors mounted on THK guides, swivels 0° - 15° for straight & angle cutting. -- Top & Bottom Trimming Unit: 2 x 0.7 HP - 12.000 RPM motors, capable of tilting & pneumatic positioning for (3) settings, flush/bevel/radius trimming for quick setup. -- Corner Rounding Unit "Round 2M": corner rounding unit with (2) 0.80 HP independent motors that slide on THK guides. -- Top & Bottom Profile Scraping Unit: with digital indicators. Large dia. copy wheels for max. accuracy and pneumatic in/out positioning. -- Glue scraping Unit: Eliminates any excess glue. -- Buffing Unit: Top/bottom, 2 x 0.25 HP - 2,800 RPM motors, tilting up to 12°.Operator & Machine Control: -- "STARTOUCH" Controller with 12" touchscreen display, capable of storing (100) programs. -- Machine automation by PLC function and encoder positioned in the panel feed track pinion. -- Diagnostics for a quick solution to errors. Process statistics data, ie. No. of pieces/edges, and track feeding.Features & Complete With: -- 2-Speed feed-speed of 40 & 60 FPM (12 & 18 MPM); 1 x 2.5 HP feed drive motor; -- 200 Hz frequency inverter for all trimming units; -- Manual adjustable top hold-down pressure beam; -- Full sound enclosure cover and outboard panel support. -- Actual Model is SCM OLIMPIC K 560 T-ER2Following items have been replaced (date) since 2021:1) 2.5KG Glue Pot (19-JUl-21)2) Recondition old glue pot (spare glue pot) (30-Aug-21)3) Replace Guillotine ( 17-Sep-21)4) New diamond corner rounders / trimmer cutters (9-Nov-21)5) Machine Optimization & Tool swaps (22-Nov-21)6) Timmers & rounders reset (15-Dec-21)7) New Servo motor & Chip (27-May-22)8) Motor programming (27-May-22)9) Servo Motor replacement / machine dial in / testing (22-Jun-22)10) Needle Roller (20-Jun-23)

SCM OLIMPIC K 600 T-ERL EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Specifications0.4 to 3 mm Roll feeding and up to 8 mm for strip feeding.Panel Capacity Min. panel width: 60 mm (2.375"); min. panel length: 140 mm (5-1/2"). Min./max. panel thickness: 8 - 54 mm (0.375" - 2.125"); min. distance between panels: 508 mm (20").Feed speed: 36 & 52 FPM (2-1/2 HP feed motor).Equipped with:Adjustable infeed fence: Manually preset with: Digital indicator, pneumatic in/out positioning.Coil feeder: For banding up to 3 mm thick with a 3 mm guillotine.Gluing Station:For EVA (Hot Melt) with: Quick change/disconnect Teflon glue pot for fast glue tanks change if needed; heat-up time approx. 8-10 Min.Pressure Section:Manual digital positioning: Teflon coated pneumatic driven roller; (2) spring-loaded idle rollers; includes: "Strip Feed Magazine".Workstations End Trimming Station: "K-SEL 2" Front & rear: 1/2 HP - 12,000 RPM Motor mounted on THK guides; swivels 0° - 15°, rapid set up between straight and angled cutting with the automatic swivel cylinder. Top & Bottom Trimming Unit: (2) 1.0 HP - 12.000 RPM Motors: Capable of tilting 0° to 25° with copy wheels; pneumatic positioning for (3) settings:Flush/bevel/radius trimming via precision digital indicators to go from 3 mm PVC to thin tape through the controller for quick set up.Corner Rounding:(2) 0.80 HP Independent motors that slide on THK guides. The features of the "Round-K" (SCM patent) allow for the double function of both the simultaneous trimming and rounding operations.Top & Bottom Profile Scraping Unit: "RAS/K" Profile scrape station for 3 mm PVC: Pneumatic positioning with digital indicators; large dia. copy wheels for max. accuracy; pneumatic in/out positioning. Buffing Unit:Top/Bottom (2) 1/4 HP - 2,800 RPM motors; tilting up to 12°.Operator Interface "STARTOUCH" Controller with: 12" Touchscreen display; capable of storing (100) programs.Machine automation: PLC Function and encoder positioned in the panel feed track pinion.Diagnostics for a quick solution to errors: Process statistics data (i.e., Number of pieces/edges and track feeding).Features & Complete with: &#9679 (1) 2.0 HP Feed drive motor. &#9679 200 Hz Frequency Inverter for all trimming units. &#9679 Manual adjustable hold-down pressure beam. &#9679 Full sound enclosure cover & outboard panel support. &#9679 Adjustable side support. &#9679 Replaceable track pads. &#9679 Digital inverter for electronic motor braking. &#9679 Acoustical safety enclosure. &#9679 Dust Collection: Working units are individually ported on the top of the safety enclosure for maximum efficiency. &#9679 Suitable Transformer for 230 V to 600 V - 3 Ph. -- Actual model: SCM OLIMPIC K 600 T-ERLNOTE: Pictured Return Conveyor is "NOT INCLUDED"

SCM ME 28T Single pre-mill, End trim, Top/bottom trim, Profile scrape, Buffing EdgebanderThe Minimax ME 28ET is a compact machine boasting capacities usually only found on much larger units. This model has a single diamond pre-milling unit with chip breaker, end trimming, top and bottom trimming, scraping, buffing stations, and 3mm edge processing (5mm strips) standard. This machine is perfect for small to medium-sized panel processing shops, this small machine packs many features, and has a favorable price as well.1-phase, compact edgebander with automatic strip magazine and 3mm radius tooling. Complete with a single pre-mill cutter head, end trimmer, top/bottom trimmers, profile scrapers, and buffing unit.PRE-MILLING UNITPanel edge surfaces without any imperfections before the gluing operation. The single-head diamond pre-mill and chip breaker ensures a clean edge that corrects any panel imperfections caused by the saw cutting and panel storage process. The independent exhaust system comes equipped with an exhaust hood and air blower which cleans and removes all dust and chips from the panel and stations. Four different thickness removals: 0.5 / 1 / 1.5 / 2 mm.INFEED FENCEAdjusted with the addition or subtraction of shims with 0.5, 1, 1.5, and 2 mm thicknesses.GLUE POT UNITThe Minimax ME 28ET edgebander features a glue pot with a quick heat-up system. The glue pot is Teflon coated to allow for easy clean up and easy glue replacement. The system easily applies the glue to the panel with a vertical glue spreading roller, and the temperature is adjustable via the PLC control. The machine also has a device to automatically recover unused glue and has a standby mode while idle.EDGE LOADINGAutomatic edge loading system for coiled edges up to 3mm thick. Pneumatic shear device for coiled edge cutting. The rotating coil-holder plate is 28.7"; (730mm) in diameter.PRESSING SYSTEMThe edgebanding is applied to the material through use of two edge steel pressure rollers with counterpoised conicity.PANEL HEIGHT ADJUSTMENTManual adjustment of the presser, with numerical readout and automatic positioning of the upper operating units according to the panel height.PLC CONTROLSThe control panel is located on the front of the machine in an ergonomic position. This unit is used to control all of the machine's functions quickly and intuitively. It has a 4-line LCD display keyboard with “soft touch"; pushbuttons and LED light indicators for the functions and adjustments of the glue pot temperature.PANEL MOVEMENT SYSTEMThe Minimax ME 28ET panel movement system is designed for a perfect finish, the very best finishing of the panel edge is further improved by the panel conveying belt (SCM patent), which prevents the panel from having the feed affected by the typical pulse generated by the pinion of a traditional feed track, which is common at slower speeds. The presser above the belt feed has support rollers that run the entire length of the machine's stations to a

SCMI K 203 SINGE SIDED EDGEBANDER5/16" (7.9 mm) Max. edge cap. for strip feeding, 1/8" (3 mm) for coil feeding; 60 mm min. panel width and 160 mm min. panel length; panel thickness 10 - 50 mm.Equipped with: Teflon coated glue pot (heat-up time 10 Min), automatic strip and coil feed magazine, 3 mm cap. guillotine, 3-roll pressure unit w/pneumatic control. --Workstations: --Double motor front & rear end trim mounted on THK guideways (0.4 HP - 12,000 RPM motor ea.), tilts 0° - 15° from the control panel with (2) preset positions. -- Top & bottom flush & bevel trims with quick release mount and plug-in motors for quick tooling changes (0.7 HP - 12.000 RPM motor ea.), bevels 0° - 15³ with precision digital indicators for quick setup. -- Top & bottom Scraping station -- Top & bottom buffing unit (0.25 HP - 2,800 RPM motors). -- 36 FPM Fixed feed speed, 0.75 HP feed drive. -- Complete with: Microprocessor for line control (can store up to 50 preset programs), control panel at eye level for easy programming, full cover sound enclosure. -- Features: Mechanical digital readouts for setup adjustments, frequency inverter and outboard panel support.

SCM UNO CS Wide Belt Sander37" Wide cap., 1-Head machine;Specifications: -- Combination head with 4" dia. 85 shore grooved rubber contact drum and 2" wide finishing platen; -- 18 HP motor; 37" x 60" abrasive belt size; 0.87 HP 2-speed feed - 15 & 30 FPM. -- Powered raise and lower w/ LED digital readout; 6-1/4" max. thickness cap., 12-1/2 min. material length. -- Includes: 5-1/2" dia. dust outlet, infeed, and outfeed hold-down roller and load meter.

SCMI OLIMPIC K 800 T-FR2 EDGEBANDER EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): Specifications: -- Edge Capacity, 0.4 to 8 mm (0.016 to 5/16") for strip feeding. -- Panel Capacity, min. width 65 mm and 140 mm min. length, (2-3/8" and 5-1/2"). Panel thickness min./max. 8 - 60 mm (3/8" - 2-3/8"). Equipped With: -- Adjustable In-feed Fence: Manually pre-set with digital indicator and pneumatic panel spacing device. -- Pre-Milling Station, RT-E: Spindles 2 x 3.0 HP, 12,000 RPM, (1) with PLC controlled jump action and manual digital indicators positioning. -- Automatic Strip & Coil Feed Magazine: For straight edges and 3 mm guillotine for coils. -- Gluing Station: For EVA (Hot Melt) with Teflon coated glue tank and quick disconnect to change glue tanks fast if needed. Heat-up time approx. 10 Min. -- Pressure Section: Servo motor positioning, (4) pressure rollers, first larger, Teflon coated and powered. Workstations: -- End Trimming Station K-SEL: Front & rear 2 x 0.5 HP, 12,000 RPM motors mounted on THK guides, swivels 0ø - 15ø, rapid set up between straight and angled cutting with the automatic swivel cylinder. -- Flush Trimming Unit: Top/Bottom, 2 x 1.0 HP, 12,000 RPM with 2 pre-set pneumatic positions, flush and overhang, remote pneumatic in/out positioning. -- Bevel/Radius Trimming Unit: Programmable, servo motor positioning, 2 x 1.0 HP - 12.000 RPM motors for change-over on the fly. -- Corner Rounding / Trimming Unit: For additional top & bottom trimming of linear an/or vertical leading & trailing corner when edgebanding all (4) sides, 2 x 0.8 HP - 12,000 RPM motor. -- Profile Scraping Unit "RAS/1000": Top/Bottom with (2) indexed manual pre-sets. Large dia. copy wheels for max. accuracy and pneumatic in/out positioning. -- Glue Scraping Unit, "RC-V": Top/bottom flat glue scraper with pneumatic positioning through controller and air-blow off nozzle to keep the knifes clean. -- Buffing Unit "SPN": Top/bottom, oscillating 2 x 0.25 HP - 3,000 RPM motors, tilting up to 12°. -- Hot Air Unit: Single blower with adjustable heat range and directional heat shield for top/bottom coverage. Restores color luster on thick pvc edging materials that my be lost during the edge scraping process.Operator Interface: -- Startouch Controller, 12" color touch screen, swivels 270° at in-feed of machine. Capable to store (100) programs, (6) at the touch of a single key. Graphical display of all working units. Tracks production data, diagnostic information and monitors maintenance schedules. Complete With & Features: -- Feed-speed, 36/52 FPM, 1 x 2.5 HP feed drive motor, 200 Hz frequency inverter for all trimming units. -- Electronic, programmable hold-down pressure beam positioning, lighted safety/sound enclosure cover and outboard panel support. -- Actual Model: OLIMPIC K 800 T-FR2

Mini Max L55 stroke sander used very little excellent working condition, 4'x8' $2,250 OBO

SCM Sandy 10 -RCS-110 Wide Belt Sander (2) Heads43" Width cap. Drum, Combination HeadHead Configuration:1st. Head: 7" diameter corrugated metal roller for calibration 35 HP ( Drives both Heads )2nd Head: Combination head with 7" dia. contact roller (spiral grooved rubber covered); air/jump finishing platen controlled with timers to eliminate any rounding on leading & trailing edges of the panel, 2" wide platen.Specifications --103" long x 43" wide Abrasive belts --Air tracking, floating & rigid bed for sanding of veneers & solid panels; infeed & outfeed spring loaded holddown rolls -- Minimum workpiece length 16" --Thickness capacity 6.25". --Separate 2.5 H.P. variable speed feed motor delivering feed speeds from 15 to 70 FPMNote: The seller has 20 boxes of various sandpaper belts (80 – 150 grit) that will be included.

SCM MINIMAX - T-3, ...Shaper3/4" Dia. solid spindle; 3 HP motor; (3) spindle speeds of 4,000 - 7,000 & 9,500 RPM; table size: 22" x 37" with table insert openings. -- Complete with: Adjustable fence; magnetic starter w/overload protection; reversing switch and 5" dia. dust outlet.

SCMI OLIMPIC S1000 T-ERL EDGEBANDER (W/PRE-MILL & CORNER ROUNDING) -- Specifications:Edge Capacity, 0.4 to 15 mm (0.016 to 5/8") for strip feeding. -- Panel Capacity, min. width 50 mm and 140 mm min. length, (2.0" and 5-1/2"). Panel thickness min./max. 8 - 60 mm (3/8" - 2-3/8"). Equipped With:&#9679 Adjustable In-feed Fence: Manually pre-set with digital indicator and pneumatic panel spacing device. -- Pre-Milling Station, RT-E: Spindles 2 x 5.25 HP, 12,000 RPM, (1) with PLC controlled jump action and manual digital indicators positioning and Diamond Cutter-heads. -- Anti-Adhesive Spraying System: Top/Bottom, positioned prior to the Pre-Milling Unit, it prevents glue buildup on the work-piece surfaces. It consists of (2) independent spray nozzles, and a tank for anti-adhesive liquids. -- Automatic Strip & Coil Feed Magazine: For straight edges and 3 mm guillotine for coils. -- Gluing Station, Vc/1000: For EVA (Hot Melt) with Teflon coated glue tank and quick disconnect to change glue tanks fast if needed. Heat-up time approx. 10 Min. -- Pressure Section: Servo motor positioning, (4) pressure rollers, first larger, Teflon coated and powered. Workstations:&#9679 End Trimming Station K-SEL: Front & rear 2 x 0.5 HP, 12,000 RPM motors mounted on THK guides, swivels 0ø - 15ø, rapid set up between straight and angled cutting with the automatic swivel cylinder. -- Flush Trimming Unit, Rsp: Top/Bottom, 2 x 1.5 HP, 12,000 RPM with 2 pre-set pneumatic positions, flush and overhang, remote pneumatic in/out positioning. -- Bevel/Radius Trimming Unit, Ri/S: Programmable, servo motor positioning, 2 x 1.0 HP - 12.000 RPM motors for change-over on the fly. -- Corner Rounding / Trimming Unit, Round-K: For additional top & bottom trimming of linear an/or vertical leading & trailing corner when edgebanding all (4) sides, 2 x 0.8 HP - 12,000 RPM motor. Comes with (2) pre-set pneumatic positions to allow to go from thick to thin pvc automatically. -- Profile Scraping Unit "RAS/1000": Top/Bottom with (2) indexed manual pre-sets. Large dia. copy wheels for max. accuracy and pneumatic in/out positioning. -- Glue Scraping Unit, "Rca/2c": Top/bottom flat glue scraper with pneumatic positioning through controller and air-blow off nozzle to keep the knifes clean. -- Buffing Unit "SPN": Top/bottom, oscillating 2 x 0.25 HP - 3,000 RPM motors, tilting up to 12°. -- Hot Air Unit: Single blower with adjustable heat range and directional heat shield for top/bottom coverage. Restores color luster on thick pvc edging materials that my be lost during the edge scraping process.Controls: -- Startouch Controller, 12" color touch screen, swivels 270° at in-feed of machine. Capable to store (100) programs, (6) at the touch of a single key. Graphical display of all working units. Tracks production data, diagnostic information and monitors maintenance schedules. Complete With & Features: -- Feed-speed, 40/60 FPM, 1 x 2.5 HP feed drive motor, 200 Hz frequency inverter for all

Sandya 10 RRCS 130 wide belt sander 3-Head, 53" width cap, Drum, Drum, Combination HeadHead configuration1st Head: Contact roll, 7" dia., 35 HP motor;2nd Head: Rubber covered contact roll, 7" dia3rd Head: Combination head, rubber covered contact roll, 7" dia. and 2" wide finishing platen, 30 HP motor driving both headsSpecification -- 52" x 103" Abrasive belts -- Air eye tracking and pneumatic belt tensioning, --All heads with abrasive belt grit thickness adjustment, -- Conveyor belt feed with dual feed speed,Equipped with & Features -- Automatic part thickness adjustment. -- Motorized thickness opening via (4) precision conveyor bed jacks -- LED readout, -- 0" - 6-1/4" opening, --Infeed and outfeed spring loaded holddown shoes. -- Motor load meters; -- Infeed and outfeed conveyor roller extensions.

DMC - 1350 RKP, ...TECHNOSAND 3-Head Wide Belt Sander.(3) Heads, 52" width cap. - Head sequence: Contact sanding roll and (2) Segmented platens Head Configuration:1st Head : 35 HP 9″ Spiral Drum2nd Head : 24 HP/30 HP dual RPM 7″ Spiral Drum/Combination Head W/Segmented Platen,3rd Head : 15 HP VFD driven multi-speed head with a Segmented Platen4th Station: Panel cleaning brush Specifications: -- 53" x 103" Long abrasive belts with electronic tracking on all wide belt heads. -- Turbo panel blowers, timed abrasive belt air cleaners. -- DMC "Hydra 35" control, "EPICS" control for sectional platens. -- (99) Programs; graphic screen for machine configuration, +/- control on segmented platens, abrasive belt cleaners. -- Sequential automatic start-up, machine troubleshooting and self-diagnosis. -- Variable feed speed from 15 - 60 FPM (4.5 - 18 MPM), 5 HP variable feed drive. -- Vacuum conveyor bed with 12 HP suction fan and motor.Equipped with & Features: -- Automatic conveyor belt tracking, infeed & outfeed holddown pinch rolls or shoes on all heads. -- 0" - 4" Motorized programmable thickness adjustment with LED readout. -- Automatic part thickness adjustment, infeed hand safety stop, outfeed emergency stop. -- Motor load meters and control console with monitor & keypad.NOTE: Sander has very low hours, less than 700. The "orange" screen is the OLD screen while the "blue" screen is the NEW screen that was replaced after the original video was made. Includes (4) spare platens.

SCM S 630 Planer with Tersa HeadSpecifications: -- 24" Width cap.; 12 HP main motor, 2 HP feed motor; 4-3/4" dia. with reversable TERSA Head rotates @ 4,500 RPM; -- 1/8" - 11-3/4" Thickness opening via motorized bed with LED readout for fine adjustment. -- Max. depth of cut 5/16"; 10" min. length of workpiece; variable infeed speed from 20 - 56 FPM.Equipped with: -- 20-3/4" x 39" Cast iron table, sectional chip breaker, sectional grooved infeed & solid outfeed rollers, adjustable bed rollers.Complete with: -- Magnetic starter and dust hood w/6" dia. dust outlet.

Belt size 43” x 85” (2) six inch dust ports 1st head 24 HP 230 2nd head 18 HP 230 Fiest head contact drum Second head combination with finish platen Feed rate 3 to 68 feet per minute Weight 4550 lbs 230 volt 3-phase

SCMI S630K Planer 10 HP Motor Straight Knives

SCMI Gang Rip Saw S/N B.540480

SCMI S630 Planer Capacity 24” x approx. 10” Straight 4-knife cutterhead Sectional chipbreaker and sectional infeed roller Cutterhead motor: 12HP, 230v (currently wired)/460v, 3PH 39” long bed with (2) idler rollers 2 rubber coated outfeed rollers with air assist Motorized raise/lower Includes manuals Solid machine. Currently replacing all bearing and thoroughly cleaning down to the bolts. Operating Instructions, Parts manual, wiring diagram included. Extra set of knives included. Weighs 2000lbs+

Working height 120 mm working width 240 mm feed speed 6-36 fpm 6’6” straightening infeed