Woodworking Equipment For Sale

Homag BST 500

Houfek Buldog 7-3M-1100-RRC 3 Head wide belt sander43" width cap, Roller / Roller / Combination-headHead Configuration1st Head – Rubber – 90 shore @ 200mm (7.9";) dia.2nd Head – Rubber - 90° shore @ 2000mm (7.9";) dia.3rd Head– Rubber - 45° shore @ 200mm (7.9";) dia. with adjustable platen.Specifications -- Sanding width 1100 mm 43" -- Work piece height 3-160 mm 0.118"~6.3" -- Sand belt size 1120 x 2620 mm 44" x 103" -- Conveyor feed speed 3~15 m/min 9.8~49 FPM -- Table motor 0.18 kW 1/4 HP Equipped with & Features -- Main motor 1st head 18 kW 24HP -- Motor 2nd head 15 kW 20HP -- Motor 3rd head 15 kW 20HP -- Voltage 460/3/60 -- Exhaust outlet (4) 180mm; (1) 100mm (4) 7"; (1) 4" -- CFM requirements 6700 m3/hr 3950 CFM -- Weight 3100 kg (approx) 6820 lbs -- Floor space 3885x1715x2260mm153"x68"x89"

Hunton Limited Punch Grinder

HYDREX HPX410-5 Hot Press 160 Tons using (8) hydraulic cylinders, Five daylight openings. Suitable for laminating veneer panels/doors, decorative paper, fireproof board, etc.Features (Overall): -- Board size up to nominal 4' x 10' (about 51" x 126"). -- Front Controls for easy setup & operating configuration, incl. temperatures and cycle time , emergency pedal, quad temperature protection device. -- (8) Cylinders (upstroke) -- 160 Tons of overall pressure, -- Recirculating Thermal Oil heated with package heaters housed in a boiler tank.Detailed Specs: -- Platen size 1300 mm x 3200 mm (51" x 126") approx. Thermal Oil heated Hot Press with drilled steel platens, 1.5" thick; -- (8) Hydraulic "upstroke cylinders", approx. 85 mm dia.; rack & Pinion guide system for parallel closing of the platens. -- 40 PSI specific pressure over the entire platen area; 54 kW heating power. Approx. 7.5 kW (10 HP) hydraulic pump motor. -- 1.5 kW (2 HP) Hot Oil circulation pump; approx. 120° C (248° F) max. operating temperature. -- Max Working height is 4"; Loading from (3) sides; 39-1/2" from floor with lower platen in the down position; Heavy I-beam welded steel frame construction. -- "Safety" emergency Stop Cable around the operating sides of the machine, and E-STOP mounted on the control panel. -- Overall press weight is approx. 27.500 Lbs. -- Optional: Extra Large Oil Heating Tank for Special Higher Temperatures if needed.

HYDREX HPX48-1 Hot Press, Single daylight opening. Suitable for laminating veneer panels/doors, decorative paper, fireproof board, etc.Features (Overall): -- Board size up to 4' x 8', -- Front Controls for easy setup & operating configuration, incl. temperatures and cycle time, emergency pedal, and quad temperature protection device. -- (6) Cylinders (upstroke) -- 80 Tons of overall pressure, -- Recirculating Thermal Oil heated with package heaters housed in a boiler tank.Detailed Specs: -- 98" x 51" Thermal Oil heated Hot Press with drilled steel platens, 1.5" thick, 4" Max Working height.. -- (6) Hydraulic "upstroke cylinders", 85 mm dia.; rack & Pinion guide system for parallel closing of the platens. -- 80 Ton total pressure, 40 PSI specific pressure over the entire platen area; 4 KW (5.5 HP) hydraulic pump motor. Platen moving speed 5 FPM -- 1.5 kW (2 HP) Hot Oil circulation pump; approx. 120° C (248° F) max. operating temperature. -- Loading from (3) sides; 39-1/2" from the floor with lower platen in the down position: heavy I-beam welded steel frame construction. -- "Safety" emergency Stop Cable around the operating sides of the machine, and E-STOP mounted on the control panel. -- Overall press weight is approx. 12,500 Lbs). Overall dimensions 129" x 65" x 102" high.Also available with (3) openings - 100 Tons and (5) openings - 100 Tons.

HYDREX HPX510-1 Hot Press, Single daylight opening. Suitable for laminating veneer panels/doors, decorative paper, fireproof board, etc.Features (Overall): -- Board size up to 5' x10', -- Front Controls for easy setup & operating configuration, incl. temperatures and cycle time , emergency pedal, quad temperature protection device. -- (8) Cylinders (upstroke) -- 120 Tons of overall pressure, -- Recirculating Thermal Oil heated with package heaters housed in a boiler tank.Detailed Specs: -- 122" x 61" Thermal Oil heated Hot Press with drilled steel platens, 1.5" thick, 4" Max Working height.. -- (8) Hydraulic "upstroke cylinders", 85 mm dia.; rack & Pinion guide system for parallel closing of the platens. -- 120 Ton total pressure, 40 PSI specific pressure over the entire platen area; 4.5 KW (6 HP) hydraulic pump motor. Platen moving speed 5 FPM -- 1.5 kW (2 HP) Hot Oil circulation pump; approx. 120° C (248° F) max. operating temperature. -- Loading from (3) sides; 39-1/2" from floor with lower platen in the down position: heavy I-beam welded steel frame construction. -- "Safety" emergency Stop Cable around the operating sides of the machine, and E-STOP mounted on the control panel. -- Features: "Last" (2) cylinders can be turned off to press shorter panels. - Overall press weight is approx. 19,500 Lbs).

HYDREX HPX510-5 Hot Press 120 Tons with (5) Daylight openings. Suitable for laminating veneer panels/doors, decorative paper, fireproof board, etc.Features (Overall): -- Board size up to 5' x 10', -- Front Controls for easy setup & operating configuration, incl. temperatures and cycle time, emergency pedal, and quad temperature protection device. -- (8) Cylinders (upstroke) -- 120 Tons of overall pressure, -- Recirculating Thermal Oil heated with package heaters housed in a boiler tank.Detailed Specs: -- 122" x 61" Thermal Oil heated Hot Press with drilled steel platens, 1.5" thick; -- (8) Hydraulic "upstroke cylinders", approx. 85 mm dia.; Rack & Pinion guide system for parallel closing of the platens. -- 120 Ton total pressure; 54 kW of heating power. 40 PSI specific pressure over the entire platen area; 4.5 kW (6 HP) hydraulic pump motor. -- 1.5 kW (2 HP) Hot Oil circulation pump; approx. 120° C (248° F) max. operating temperature. -- Max Working height is 4"; Loading from (3) sides; 39-1/2" from the floor with lower platen in the down position: heavy I-beam welded steel frame construction. -- "Safety" emergency Stop Cable around the operating sides of the machine, and E-STOP mounted on the control panel. -- Features: "Last" (2) cylinders can be turned off to press shorter panels. - Overall press weight is approx. 24,000 Lbs. -- Overall dimensions: 3,800 length (+610mm -boiler + 610mm -pump/tank) x 1,790 wide x 2,450 mm high.

2004 Hymmen Proficoater 60" Roll Coat Line - Model ULX-S: Includes spare drum and lights SCMI Finish Sander

IMA - HKA EXPERT CONTOUR EDGEBANDER: Specifications: -- Manually operated Contour Edgebander. Designed for straight or curved (contour) edgebanding:0.5 - 3 mm Edgebanding thickness; 16 - 45 mm (0.63" - 1.77") panel & banding height; 23 - 45 mm (0.9" - 1.77") min. strip width; 100 mm (3.9") min. panel width; 250 mm (9.8") min. strip length. -- Equipped with: Versatile glue head that can be fixed to 1-side of the table to allow the operator to manually manipulate smaller pieces.During "fixed" mounted operation, coil material is drawn in automatically to infeed section of machine, via foot-pedal control. -- Work Table:32" (800 mm) Dia. coil dispensing table, large 813 x 914 mm (32" x 36") High-Flow Phenolic worktable surface;Pre-selection counter for edgebanding material; (1) preheating unit with 600 Watts for preheating of PVC/ABS edges -- Operating Process:Floating edgebanding head is clamped to panel to be processed, precut strip of edgebanding material is fed into glue head,Operator guides head around workpiece, glue is directly applied to precut strip of edgebanding material up to end of strip. -- Features: "Floating head (hot melt) glue pot" with 0.5 Liter cap; Guillotine knife for PVC material (within floating head). -- Complete with: &#9679 (1) 6 m³/Hr cap. vacuum pump for high-flow work table; &#9679 Jib Crane & hoist to support the edgebanding head; &#9679 Thermo-control for glue temperature; &#9679 Foot pedal control to initiate automatic cycle.

IMA - HKA CONTOUR EDGEBANDER: Specifications: -- Manually operated Contour Edgebander. -- Designed for straight or curved (contour) edgebanding with: 0.5 - 3 mm Edgebanding thickness, 16 - 45 mm panel & banding height, 23 - 45 mm min. strip width; 100 mm min. panel width; 250 mm min. strip length. -- Equipped with: Versatile glue head can be fixed to 1-side of the table allows operator to manually manipulate smaller pieces.During "fixed" mounted operation, coil material is drawn in automatically to infeed section of machine. -- Work Table:32" (800 mm) Dia. coil dispensing table, large worktable surface (approx. 36" x 36"); Pre-selection counter for edgebanding material; (1) preheating unit with 600 Watts for preheating of PVC/ABS edges -- Operating Process:Floating edgebanding head is clamped to panel to be processed, precut strip of edgebanding material is fed into glue head,Operator guides head around workpiece, glue is directly applied to precut strip of edgebanding material up to end of strip. -- Features: "Floating head/glue pot" unit (hot melt) with 0.5 Liter cap; Guillotine knife for PVC material (within floating head). -- Complete with: &#9679 (1) 6 m³/Hr cap. vacuum pump for high-flow work table; &#9679 Jib Crane & hoist to support the edgebanding head; &#9679 Thermo-control for glue temperature; &#9679 Foot pedal control to initiate automatic cycle.

IMA Combiform I/R75/1260/V

MA Hot Melt Glue Edgebander, Designed to allow operation by feeding parts past the glue head using the table and ball rollers, or the part can be vacuum mounted to the table (Vac Pump and Vac Pods included) with the head guided manually around the part with the weight of the applicator head counter-balanced from the boom. Specifications: Board Thickness 16mm to 45mm(0.630" - 1.77"), Strip Height 20mm-50mm (0.78"-1.97"), Strip Thickness 0.4mm to 3mm (0.016" - 0.118"), Glue Tank 0.8Liter (48 Cubic Inches, or 0.8 quart ), Processing Temperature 140 to 220 C Degrees ( 284F-428F). Current running 8 Amps, Glue Pot 1400 Watts, Max Overall Watts 2600. Weight of Movable head 20kg ( Note: this 45 lbs head weight is counter-balanced with spring.) Working height 960mm (37 3/4")

IMA Advantage 500L single sided edgebander - Single sided edgebander for EVA glue - Joint-milling, gluing unit with double coil magazine, top pressure mounted end trimming, pre/flush-trimming, corner rounding, profile– and glue scraper, buffing and smoothing units - Tooling: Multi Milling Unit, 3mm corner rounding unit

IMA 500L Edgebander Will need a new touch screen control and calibration.

IMA ADVANTAGE 500 L EDGEBANDER (w/PREMILL & CORNER ROUNDING): -- Specifications:Edgebanding capacity: Coiled material: 0.3 - 3 mm (0.012 - 0.118"); strips 3.0 - 12.0 mm (0.118 - 0.472); panel thickness min./max. 8 - 60 mm (0.315 - 2.362").Equipped with:Pre-milling Unit: 4 kW x 2 (5.3 HP x 2) - 9,000 RPM Vertical joining spindles; SIKO digital readouts, and particle & debris air jet blower. -- Glue System - EVA (Hot Melt) with: "Quick-Lock" System. -- Pressure Section with: (1) Large dia. driven and (5) idle rollers. Workstations:End Trimming Unit: Dual motor, (2) 0.66 kW (0.88 HP) motors; suspended from the hold-down beam; automatic chamfer adjustment 0° - 8°. -- Rough Trimming Unit: Top & Bottom flush trimming, W 1.0 kW x 2 (1.34 HP x 2) - 12,000 RPM Ea. motor; against the feed (up milling), vertical & horizontal tracing wheels, digital readouts for adjustments. -- Contour Unit: Multiuse; Top & Bottom linear and vertical corner trimming; total motors: (4) 2 x 180 W and 2 x 400 W - 12,000 RPM. -- Profile Scraper Unit: Profile Scrapers for up to 3 mm thick PVC banding, vertical & horizontal tracing shoes. -- Glue Scraping Unit: Flat, Top & Bottom self-tracing Glue Scraper. -- Buffing Unit: Top & Bottom 0.18 kW x 4 (0.25 HP x 4) - 1,400 RPM. -- Edge Smoothing Unit: Top & Bottom for 1, 2 & 3 mm edge.Control System ICOS OPEN TS: Large color LCD display; displays stored data, on/off workstation sequence, troubleshooting diagnostic; data input by touchscreen, alphanumeric keyboard, and mouse. Microprocessor adjusts according to stored programs or input; pressure section position & pressure control, vertical positioning of all holddown beam mounted workstations.Complete with:Heavy-Duty "sliding" feed chain with: 70 mm Wide x 60 mm long rubber pad inserts; central lubrication of transport chain; variable feed speed from 4 - 20 MPM (13 - 65 FPM). -- Motorized central height adjustment of top pressure beam with double V-belt hold-down. -- Sound Enclosure - All stations; all trimming & milling motors DC electrical motor brakes for immediate stopping. -- Spraying Units: Upfront at infeed for anti-stick solvent and polishing solvent prior to Buffing Station. -- Actual Model is I M A ADVANTAGE 500 L

IMA ADVANTAGE 500 L EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): Production Edgebander -- Specifications:Edgebanding capacity: Coiled material 0.3 - 3 mm (0.012 - 0.118"); strips 3.0 - 12.0 mm (0.118 - 0.472); panel thickness min./max. 8 - 60 mm (0.315 - 2.362").Equipped With:Premill Unit - 08.379 with: 4 kW x 2 (5.3 HP x 2) 9,000 RPM Vertical joining spindles, SIKO digital readouts, particle & debris air jet blower. -- Glue System - EVA (Hot Melt) with: "Quick-Lock" System. -- Pressure Section with: (1) Large dia. driven and (5) idle rollers. Workstations:End Trimming Unit - 08.415: Dual motor, 0.66 kW x 2 (0.88 HP x 2) suspended from the hold-down beam; automatic chamfer adjustment 0° - 8°. -- Rough Trimming Unit - 08.055: Top & Bottom flush trimming, W 1.0 x 2 (HP 1.34 x 2) - 12,000 RPM ea. motor; against the feed (up-milling), vertical & horizontal tracing wheels, digital readouts for adjustments. -- Contour Unit - CT U-L: Multiuse, Top & Bottom linear and vertical corner trimming; total motors: (4) 2 x 180 W and 2 x 400 W; 12,000 RPM. -- Profile Scraper Unit - 08.519: Profile Scrapers for up to 3 mm thick PVC banding, vertical & horizontal tracing shoes. -- Glue Scraping Unit - 08.521: Flat, Top & Bottom self-tracing Glue Scraper. -- Buffing Unit - 08.617-2: Top & Bottom 0.18 kW x 4 (0.25 HP x 4) - 1,400 RPM. -- Edge Smoothing Unit: Top & Bottom for 1, 2 & 3 mm edge.Control System ICOS OPEN TS: Large color LCD display; displays stored data, on/off workstation sequence, troubleshooting diagnostic; data input by touchscreen, alphanumeric keyboard, and mouse. Microprocessor adjusts according to stored programs or input; pressure section position & pressure control, vertical positioning of all hold-down beam mounted workstations.Complete with:Heavy-Duty "sliding" feed chain with: 70 mm Wide x 60 mm long rubber pad inserts; central lubrication of transport chain; variable feed speed from 4 - 20 MPM (13 - 65 FPM). -- Motorized central height adjustment of top pressure beam with double V-belt hold-down. -- Sound Enclosure - All stations; all trimming & milling motors DC electrical motor brakes for immediate stopping. -- Spraying Units: Upfront at infeed for anti-stick solvent and polishing solvent prior to Buffing Station. -- Actual Model is IMA ADVANTAGE 500 L

IMA NOVIMAT COMPACT/I/G80/700/L12 EDGEBANDER (W/ PRE-MILL & CORNER ROUNDING): -- Basic Specifications:Edgebanding coil stock capacity, 0.3 - 3 mm; (0.012 - 0.118"), Strips up to 12mm (0.47") can be processed. Panel thickness min/max 8 - 60 mm (0.315 - 2.362").Equipped With: -- Spraying Unit, anti sticking solvent, top and Bottom application. -- In-feed Fence with N.C. servo motor positioning. -- Pre-Milling Unit 08.378, with kW 4.5 x 2 (HP 6 x 2) vertical joining spindles, N.C. controlled, both w/jump movement and reversible rotation, SIKO digital readouts, particle & debris air jet blower. -- Edge Pre-heating Lamps, for best possible glue bond. -- Glue System: EVA Glue (Hot Melt) + 1 Quick Melt unit. -- Side Pressure Section: N.C. controlled, with (5) pressure rollers w/individual pneumatic pressure control for each roll -- Edge Magazine: Vertical coil cartridge assembly, 1 x 6 positions with auto edge-selection and HD guillotine.Workstations: -- End Trimming Unit 08.0555: High speed, double motor KW 0.66 x 2 (HP 0.88 x 2) suspended from the hold-down beam, automatic chamfer adjustment 0° - 15° for speeds up to 32 m/min (105 ft./min). -- Flush/Bevel/Radius Trimming Unit: Top & bottom, multi profile, N.C. controlled, KW 1.5 x 2 (HP 2.0 x 2) - 12,000 RPM motors, bevels 0°-30°, vertical & horizontal tracing wheels, digital read-outs. -- Corner Rounding Unit KFA 25: High Speed, (1) x Kw 0.66 (HP 0.88), 12000 RPM motor with multi-profile and N.C. servo positioning. -- Profile Edge Scraping Unit: Top & bottom, multi-profile (4) positions N.C. controlled scrapers for up to 3 mm thick PVC banding, vertical & horizontal tracing wheels, digital readouts for adjustments, chip extraction system for scraping unit. -- Glue Scraping Unit: Flat, top & bottom self-tracing glue scraper, N.C. controlled. -- Buffing Unit: Double Stage, (2) top & (2) bottom KW 0.18 x 4 (HP 0.25 x 4) - 3,000 RPM ea. motor for linear & vertical corner edge polishing. -- Glue Scraping Unit: Flat, top & bottom self-tracing glue scraper. -- Buffing Unit: Top/Bottom (2) x KW 0.18 (HP 0.25) - 3,000 RPM ea. motor.Operator Interface: -- ICOS OPEN, Large color LCD display; displays stored data, on/off work station sequence, troubleshooting diagnostic; data input by alphanumeric keyboard. Microprocessor adjusts according to stored programs or input; pressure section position & pressure control, vertical positioning of all hold-down beam mounted workstations.Complete With: -- Heavy Duty "sliding" feed chain with 80 mm wide x 60 mm long rubber pad inserts, central lubrication of transport chain, -- Variable Feed Speed 6 - 30 MPM (20 - 98 FPM); -- Motorized central height adjustment of top pressure beam with double V-belt hold-down. -- Frequency inverters; ball bearing guided outboard panel support up to 27-1/2", sound enclosure, all stations, all trimming & milling motors DC electrical motor brakes for immediate stopping. -- Spraying Unit with polishing solvent prior

IMA BIMA-610, 4' x 16’ CNC MACHINING CENTER , (1998), (460/60/3 electrics), S-4535 General Specifications: - 10 HP, 230/460/60/3 tool-changer type router spindle - (12) station traveling rotary tool changer - (1) 7-spindle & (1) 5-spindle point-to-point vertical drill blocks - X & Z axis ball-screw & Y-axis rack & pinion - Adjustable pod and rail system, (10-rails with pods) - Can include a 4’ x 8’ “universal” flow vacuum table for nested base processing - Integrated scrap conveyor under/through the working area - IMAWOP, (Windows workshop-oriented PC programming system) - Hand held start/stop spindle speed control - 3 HP Becker vacuum pump for the pod & rail side - Includes computer, an aggregate horizontal boring unit, and additional tooling - Note: the retrofitted nested base table is not included - 25' long x 9'8" wide x 8' tall

IMA Bima 810 V

Specifications comming