Edgebanders For Sale

UNIQUE - 110: T-Moulding ApplicatorSpecifications -- Table size: 32"; x 48"; x 35"; H.Machine Dimensions: 48" x 32" x 38" H.Machine with Pallet Dimensions: 48" x 40" x 43" H.

//This machine is in an Auction on exfactoryauctions.com// //Link to machine: http://exf.ac/i5h VANTEDGE MM 6.5 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): + EVA & Polyolefin Adhesive ready. Specifications: Working Capacity: Edgebanding thickness 0.4 - 3 mm coil stock capacity & 10 mm strip capacity. Min. panel width 85 mm (3.3"); min. panel length 125 mm (4.9"); panel thickness 10 - 60 mm (0.39" - 2.36"). Tape and Panel Infeed System: 750 mm Coil support table; adjustable track feed speed 14, 16 & 20 MPM (66 FPM). Heavy-Duty large solid polished steel panel infeed fence guide system. Large industrial digital adjustment for the Premill panel material removal amount. Top Pressure Beam Adjustment: Automatic adjustment from the PLC control; pneumatic Pop-Up Stop system. Red LED panel feed indicator light for correct panel spacing. Equipped with: Dual 3 HP Pre-milling motors w/diamond cutter heads; pneumatic "JUMP In/Out function. Misting unit prior to Pre-milling; large dual dust housing ports to help clean the Pre-milling system. Quick change Glue Reservoir for EVA & PO glues; Pressure Section/Infrared Heat Lamp System. Heavy-Duty automatic shear type Guillotine with: "Auto-Set" automatic intervention for strip & coil materials. (4) Pneumatic polished Pressure Rollers with manual digital adjustment to edge thickness. (1) Rubber infeed Tape Roller, (1) metal infeed Tape Roller; direct Universal Drive system - NO Chains. Teflon-coated glue pot; digital thermostats with automatic kick down when the machine is in idle mode. Workstations: End Trimming Unit: Dual 0.5 kW (0.67 HP) high frequency End Trim motors on precision "Auto Lube" Linear Guideways; 90° to 10° pneumatic tilt cut adjustment. Electronic sensors to safely monitor motor positions; thumb screw pneumatic adjustments for simplicity. Tilting Super Finish Top & Bottom Trimming Station: Dual High Frequency 0.65 kW (0.75 HP) motors with Combi Finish insert tooling.Top Servo driven positioning of motors for different edge trimming profiles & positions. Corner Rounding Unit: Motors on precision billet aluminum swing tracer arms with pneumatic guidance and Face Copy System. (2) Independent motors can be adjusted to match tape thickness via digital scales. Profile Scraping Unit: Top, bottom & side Copy Wheels to properly follow your panels edge. Panel Nesting System: Triple Copy System for panels with blind dados & hinge cup holes. Digital adjustment for fine-tuning the unit to the proper tape thickness. Flat Scraping Unit: Large copy wheels. Buffing Unit: Top & bottom Buffing Unit; 0.5 HP (0.37 kW) - 2,800 RPM motors; units tilt 0° - 30°. Dual Hot Air Blowers: To re-embellish edge materials. Operator Interface 10" Color touchscreen PLC with swivel Control Panel. The PLC controls all working units & the adhesive thermostats with 1-touch icon programmable selections. Photo indicator alarms to easily troubleshoot errors/issues. Complete with: I

VECTOR - REVOLUTION 180 CNC: Contour Edgebander + Vector Vision UpgradeNumerically controlled automatic Edgebanding Machine precisely applies ABS & PVC edgebanding automatically to square or irregularly shaped parts as the banding head travels on a bridge gantry along the X - Y & Z axis.Machine FeaturesBanding unit simultaneously rotates on a high precision C-Axis; AC Brushless Servo motors with: Digital drives & linear guides ensure high speeds & accuracy with a smooth acceleration-and-deceleration. -- NO PROGRAMMING required; extremely simple changing from one tape size to another; Operator only has to make simple adjustments like: Setting the start position, glue height, feeding the new width of tape, and adjusting tape guide height. All else is performed by the machine. -- Cartridge Glue System. Glue height is set by positioning a pin in a hole in the index ring setting for the glue dosing rod; standard positions are: 16 mm (5/8"); 19 mm (3/4"); 25 mm (1.0"); 28 mm (1-1/8"); and 31 mm (1-1/4") eliminating any need for fine adjustment. -- Working FieldX-Axis 139.7" (3,550 mm); Y axis 72" (1,830 mm); 0.63" - 1.57" (16 - 40 mm) min. - max. material thickness.0.79" (20 mm) Min. external radius & 1.97" (50 mm) min. internal radius, depending on the type of banding materials. 1 mm Min. banding material thickness & 3 mm max. banding material thickness. (NOTE: 1 mm PVC is not suitable for butt joints). -- WorktablePhenolic worktable with: Embedded vernier scales in X & Y axes allow simple & flexible positioning of 2-stage vacuum pods. Worktable allows single or pendulum processing with: (2) 48" x 72" (1,219 x 1,828 mm) Work Zones for processing small to large parts.Average cycle times under (2) minutes; Contour Edgebander consistently produces quality parts, including 360° lap joints.Workpiece supported by means of: Vacuum cups sitting on a large flatbed; enables absolute flexibility in positioning pods to ensure the workpiece is held securely. Full vacuum achieved with: 100 cbm/Hr Vacuum Pump. Pump is mounted inside the frame of the machine reducing noise and avoiding airborne dust.Exact workpiece positioning is not critical as the patented VECTOR "Revolution 180" Operating System is unaffected by panel position.Patented process is controlled by a simple & intuitive interface; does not require CNC programming. -- Edge Banding UnitVECTOR "Revolution 180" Uses: Cartridge & nozzle glue extrusion system, which is ideally suited to this Contour Banding application.Cartridge Glue Nozzle: Closed system, which only heats the glue as it is used. Glue is not exposed to the atmosphere. RESULT: No burning of the glue or discoloration, and the original color of the glue & its properties are maintained.Glue Nozzle System: Close proximity to the 1st pressure roller. When slowing for corners, the glue remains molten until pressed onto the panel by the 1st pressure roller. This is important when banding tight radii as the glue does not have an opportunity to c

VECTOR - REVOLUTION 180: CNC Contour Edgebander + Vector Vision UpgradeNumerically controlled automatic Edgebanding Machine: Precisely applies ABS & PVC edgebanding automatically to square or irregularly shaped parts as the banding head travels on a bridge gantry along the "X", "Y" & "Z" axis.Machine FeaturesBanding Unit: Simultaneously rotates on a high precision "C" Axis; AC Brushless Servo motors with: Digital drives & linear guides ensure high speeds & accuracy with a smooth acceleration & deceleration. -- NO PROGRAMMING required: Extremely simple changing from one tape size to another; Operator only has to make simple adjustments such as setting: Start position the glue height; feed the new width of tape; adjust the tape guide height. All else taken care of by the machine. -- Cartridge Glue System: Glue height is set by positioning a pin in a hole in the index ring setting for the glue dosing rod; standard positions are: 16 mm (5/8"); 19 mm (3/4"); 25 mm (1.0"); 28 mm (1-1/8"); 31 mm (1-1/4") eliminating any need for fine adjustment. -- Working Field"X" Axis 139.7" (3,550 mm); "Y" Axis 72" (1,830 mm); 0.63" - 1.57" (16 - 40 mm) min. - max. material thickness.0.79" (20 mm) Min. external radius & 1.97" (50 mm) min. internal radius depending on the type of banding materials. 1 mm Min. banding material thickness; 3 mm max. banding material thickness. (NOTE: 1 mm PVC is not suitable for butt joints). -- WorktablePhenolic worktable with: Embedded vernier scales in "X & Y" axes; allow simple & flexible positioning of 2-stage vacuum pods. Worktable allows single or pendulum processing with: (2) 48" x 72" (1,219 x 1,828 mm) Work zones for processing small to large parts. With average cycle times under (2) minutes, the Contour Edgebander consistently produces quality parts, including 360° lap joints.Workpiece is supported by: Vacuum cups sitting on a large, flat bed; enables absolute flexibility in positioning pods to ensure the workpiece is held securely. Full vacuum is achieved with: 100 cbm/Hr Vacuum Pump. Pump is mounted inside the frame of the machine reducing noise & avoiding airborne dust.Exact workpiece positioning is not critical, as the patented VECTOR "Revolution 180" Operating System is unaffected by panel position.Patented process is controlled by: Simple & intuitive interface that does not require CNC programming. -- Edge Banding UnitVECTOR "Revolution 180" uses: Cartridge & nozzle glue extrusion system, which is ideally suited to this Contour Banding application.Cartridge Glue Nozzle is: Closed system, which only heats the glue as it is used. Glue is not exposed to the atmosphere; there is no burning of the glue or discoloration & the original color of the glue & its properties are maintained.Another Glue Nozzle System benefit: Close proximity to the 1st pressure roller when slowing for corners; glue remains molten until pressed onto the panel by the 1st pressure roller. This is important when banding tight radii as the glue doe

VECTOR - REVOLUTION 180: CNC Contour Edgebander Numerically controlled automatic Edgebanding Machine precisely applies: ABS & PVC Edgebanding automatically to square or irregularly shaped parts as the banding head travels on a bridge gantry along: "X", "Y" & "Z" axes.Machine FeaturesBanding unit simultaneously rotates on a high precision "C" axis; AC Brushless Servo motors with: Digital drives & linear guides ensure high speeds & accuracy with a smooth acceleration & deceleration. -- NO PROGRAMMING Required: Extremely simple changing from one tape size to another; Operator makes simple adjustments: Setting the start position & glue height; feeding the new width of tape; adjusting the tape guide height. All else done by the machine. -- Cartridge Glue System. Glue height set by: Positioning a pin in a hole in the index ring setting for the glue dosing rod; standard positions are: 16 mm (5/8"), 19 mm (3/4"), 25 mm (1.0"), 28 mm (1-1/8"), 31 mm (1-1/4") eliminating any need for fine adjustment. -- Working Field"X" Axis 139.7" (3,550 mm); "Y" axis 72" (1,830 mm); min. - max. material thickness: 0.63" - 1.57" (16 - 40 mm).0.79" (20 mm) Min. external radius; 1.97" (50 mm) min. internal radius, depending on the type of banding materials. 1 mm Min. banding material thickness & 3 mm max. banding material thickness (NOTE: 1 mm PVC is not suitable for butt joints). -- WorktablePhenolic worktable with: Embedded vernier scales in "X & Y" axes allows for simple & flexible positioning of 2-stage vacuum pods. Worktable allows single or pendulum processing with: (2) 48" x 72" (1,219 x 1,828 mm) Work Zones for processing small to large parts.Average cycle times under (2) minutes; Contour Edgebander consistently produces quality parts, including 360° lap joints.Workpiece: Supported by means of vacuum cups sitting on a large flatbed; enables absolute flexibility in positioning pods to ensure the workpiece is held securely. Full vacuum is achieved with a 100 cbm/Hr vacuum pump; pump is mounted inside the frame of the machine reducing noise & avoiding airborne dust.Exact workpiece positioning is not critical, as the patented VECTOR "Revolution 180" Operating System is unaffected by panel position.Patented process controlled by: Simple & intuitive interface that does not require CNC programming. -- Edgebanding UnitVECTOR "Revolution 180" uses: Cartridge & nozzle glue extrusion system, which is ideally suited to this Contour Banding application.Cartridge Glue Nozzle. Closed system, which only heats the glue as it is used. Glue is not exposed to the atmosphere: Meaning no burning of the glue or discoloration; original color of the glue & its properties are maintained.BENEFIT: Glue Nozzle System is in close proximity to the 1st pressure roller; meaning: Even when slowing for corners, glue remains molten until pressed onto the panel by the 1st pressure roller. This is important when banding tight radii, as glue does not have an opportunity to chill before being presse

VIRUTEX - EB 25: Hot Air EdgebanderFor preglued PVC, veneer and melamine laminate coil stock; 0.4 - 1.0 mm edge thickness; up to 65 mm panel thickness cap.; automatic coil & single edge strip feed.Equipped with: -- Thermostatically controlled hot air blower; 3,300 Watts for up to 500° C temperature; (2 - 3) Min heat up time. -- Guillotine type front & rear end trim (with fast speed, flying knife); top & bottom flush trims with single motor drive to cutterheads. -- Overhead belt type feeder; 15 FPM feed speed. -- Mounted on machine base with panel support table.Includes: Used tooling on the machine.

Vitap Quartz Edgebander Hot air Edgebander for pre-glued edging material 0.4-1.2 mm Will accept panels up to 35mm thick Electronically controlled temperature setting up to 650^F Guillotine style end trim & top/bottom flush trim 16 FPM feed 67" x 48" x 60" 220#

For pre-glued PVC, veneer, & melamine laminate coil stock; 0.4 - 1.2 mm edge thickness; up to 35 mm panel thickness cap., automatic coil feed. -- Equipped with: Electronically controlled temperature setting for hot air blower; 3,000 Watts for up to 650° F temperature; (1) Min heat up time. -- Guillotine type front & rear end trim (with fast speed, flying knife); top & bottom flush trims with single motor drive to cutterheads. -- Overhead belt type feeder; 16 FPM feed speed. -- Mounted on machine base with panel support table.