Sawmill Equipment For Sale

Ingersol-Rand Pac-Air screw compressor, 125 hp electric motor, not tested but appears good

7 1/2 HP. electric motor, 200 gal. vertical tank, good condition

Ingersoll-Rand screw compressor, 50 hp electric power, approx 225 CFM, good operating condition

INGERSOLL RAND SSR-EP30SE Rotary Screw CompressorSpecifications: -- 30 HP Motor, approx. 120 CFM @ 125 PSI, totally integrated package, single stage rotary screw air end, max. modulate pressure 128 PSI; full sound enclosure keeps noise levels below 75 dBA.Features: -- "Intellisys" Microprocessor based control system, premium instrument panel, air-to-air 2-stage after-cooler, electronic stepper motor inlet air control, sealed SSR direct drive gear train, total positive lubrication system with spin-on filter.Control system includes: -- Finger touch membrane panel, LED diagnostic readout with (8) operating conditions, (12) programmable operating parameters, (4) fault warnings, and (11) fault shutdowns.(23,069) Total operating hours.

INGERSOLL-RAND UP6-15C-125 15 HP Single-Stage Horizontal Tank-Mounted Rotary Screw Air Compressor, with 2,313 Hrs. (as of 2/16/24)Specifications: -- Cap. 55 CFM, Max. pressure 125 PSI. -- Pump speed 6,250 RPM. -- Sound level 69 dBA. Equipped with: -- High efficiency close coupled air end. -- Motor shaft-mounted centrifugal blower. -- Electronic stepper motor inlet air control. -- 2-Stage Air-cooled aftercooler. -- Total positive lubrication system, with Spin-on filter. -- Compartmentalized sound enclosure.Complete with: -- 80 Gallon Cap. 24"; Dia. x 33"; L Horizontal Air Receiving Tank.

Ingersoll-Rand Mdl# T-30 Tank Mounted Air Compressor Pump w/No Motor

Ingersoll-Rand Mdl# SSR-EP30U 30Hp Rotary Screw Compressor

Ingersoll Rand SSR II 50 HP screw type air compressor, believed to have 20,000 hours, Ingersoll Rand Model TS2A dryer 150 PSI Max refrigerant dryer (ref #174), 460V 3 phase, Approximate 220 CFM, Call Rachel for more information 931-797-6284

Inovec Positioning & Control System. 30hp Electric / Hydraulic Power Unit to Run Log Knees with Salem Computerized Networks S/N 195839-03

INTERNATIONAL - 1295-44, ...Horizontal Closed Door BalerSpecifications: -- Cylinder: 7" -- Feed opening: 42" x 50" -- Main motor: 30 HP

INTERNATIONAL - 1295-44, ...Horizontal Closed Door BalerSpecifications: -- Cylinder: 7" -- Feed opening: 42" x 50" -- Main motor: 30 HP

INTERNATIONAL - IB-4430-60-HD, ...Automatic Tie Horizontal BalerSpecifications: -- Bale size: 44" x 30" -- Hopper opening: 42" x 60" -- Cylinder bore: 8" -- Cylinder stroke: 82" -- Tension cylinder: 6" -- Cycle time: 15 Sec (no load) -- Ram force: 150,800 Lbs -- Main motor: 40 HPEquipped with: -- Oil cooler

INTERNATIONAL - MT-4843, ...Manual-Tie Horizontal Baler with Infeed ConveyorSpecifications: -- Cylinder: 8". -- Opening size: 60" x 46". -- Main motor: 40 HP.Equipped with: -- Control panel. -- Oil Cooler – Air-Over-Oil. -- 10' Bale Run-Out Table. -- High-Temp/Low Oil Level Shutdown. -- 48" x 43" x 60" Bale Size.

INTERNATIONAL TITAN-60-EC Full Eject Horizontal Baler with ConveyorSpecifications: -- Cylinder: 8" -- Main motor: 20 HP -- Feed opening: 58"; x 35"; -- Bale Size: 60"; x 48"; x 30"; -- Feed conveyor width: 48" -- Ram face pressure: 3,000 PSI -- Total force: 150,800 Lbs -- Cycle time: 32 Sec (14 Sec short stroke)Equipped with: -- Programmable controller with Ethernet -- Conveyor controls and conveyor hopper

INTERNATIONAL TITAN 6-EC Closed Door Horizontal Baler with ConveyorSpecifications: -- Cylinder: 8"; -- Motor: 20 HP -- Cycle time: 32 Sec Cycle Time -- System pressure: 3,000 PSI -- Total force: 150,800 Lbs -- Ram face pressure: 87 PSI -- Feed opening: 58"; x 35"; -- Bale size: 60"; x 48"; x 30"; Equipped with: -- Feed conveyor: 48" wide -- Programmable controller -- Ethernet connection

INTERNATIONAL - AT-4843-850-60, ...Auto-Tie Horizontal BalerSpecifications: -- Cylinder: 8" -- Opening size: 60" x 46" -- Main motor: 50 HPEquipped with: -- Control panel -- Oil Cooler: Air-Over-Oil -- 10' Bale Run-Out Table -- High temp/low oil level shutdown

IBC - "IBC 4343 X 8 – 50 - 63": Horizontal Auto-Tie Baler -- Model: AT-4343-8-50-63. -- Type: Auto-Tie Baler. -- Motor: 50 HP. -- Cylinder Bore: 8";. -- Bale Size: 43"; x 43"; x Variable. -- Manufacturing Date: 2009.

IBC - NA-1296A-48: Horizontal Closed-Door Baler Model -- 50 HP Motor. -- Main Cylinder: 10″. -- Bale Size: 30″ x 45″ x 60″. -- Hopper Size: 57″ L x 45″ W. -- Platen Pressure: 134 PSI. -- System Pressure: 3,000 PSI. -- Total Force: 235,620 Lbs. -- New cylinder installed approximately (6) months ago.

INTERNATIONAL - NA-1295HD, ...Closed Door Horizontal BalerSpecifications: -- Bale size: 72" x 44" x 36" -- Main cylinder bore: 8" -- Total force: 113,000 Lbs -- Ram face pressure: 71 PSI -- Feed opening: 42" x 50" -- Cycle time: 30 sec -- Main motor: 30 HPFeatures: -- PLC Control -- Bale table -- Shear bar -- Heavy-duty welded construction -- Heavy-duty hydraulic system -- Easy-to-operate controls

INTERNATIONAL BALER - IB-4430-50, ...Auto-Tie Horizontal BalerSpecifications: -- Cylinder: 8". -- Ram force: 125,660 Lbs. -- (6) Tension cylinders: 4" Bore. -- Feed opening: 42" x 50". -- Main motor: 40 HP.Equipped with: -- Shear blade with adjustable striker bar. -- Regin hydraulics. -- LED Indicators for bale functions. -- Autostart electronic beam. -- Oil cooler. -- Replaceable T-1 floor.NOTE: Ram needs some repair.