Sawmill Equipment For Sale

Ingersol-Rand Pac-Air screw compressor, 125 hp electric motor, not tested but appears good

INGERSOLL-RAND UP6-15C-125 15 HP Single-Stage Horizontal Tank-Mounted Rotary Screw Air Compressor, with 2,313 Hrs. (as of 2/16/24)Specifications: -- Cap. 55 CFM, Max. pressure 125 PSI. -- Pump speed 6,250 RPM. -- Sound level 69 dBA. Equipped with: -- High efficiency close coupled air end. -- Motor shaft-mounted centrifugal blower. -- Electronic stepper motor inlet air control. -- 2-Stage Air-cooled aftercooler. -- Total positive lubrication system, with Spin-on filter. -- Compartmentalized sound enclosure.Complete with: -- 80 Gallon Cap. 24"; Dia. x 33"; L Horizontal Air Receiving Tank.

INGERSOLL RAND SSR-EP30SE Rotary Screw CompressorSpecifications: -- 30 HP Motor, approx. 120 CFM @ 125 PSI, totally integrated package, single stage rotary screw air end, max. modulate pressure 128 PSI; full sound enclosure keeps noise levels below 75 dBA.Features: -- "Intellisys" Microprocessor based control system, premium instrument panel, air-to-air 2-stage after-cooler, electronic stepper motor inlet air control, sealed SSR direct drive gear train, total positive lubrication system with spin-on filter.Control system includes: -- Finger touch membrane panel, LED diagnostic readout with (8) operating conditions, (12) programmable operating parameters, (4) fault warnings, and (11) fault shutdowns.(23,069) Total operating hours.

Ingersoll-Rand Mdl# SSR-EP30U 30Hp Rotary Screw Compressor

Ingersoll-Rand Mdl# T-30 Tank Mounted Air Compressor Pump w/No Motor

INGERSOLL RAND 5 HP Compressor, 17.1 CFM @ 90 PSI, 80-gal. Vertical Tank.Designed with: 2-Stage (2) cylinder cast iron pump, splash lubricated, inter-cooler, after-cooler, large dia. pressure gauge and air filter. -- Features: -- Ingersoll's T-30 series pump with high performance, proven design and dependable. -- Complete with: -- Tank mounted starter, automatic tank drain, heavy pressure switch, low oil switch, oil level sight-glass and fully covered belt guard; durable painted finish, service-and-operators manual. -- Also includes: -- Ingersoll-Rand refrigerated air dryer "DS35" with max. inlet temp of 140°F, Outlet Temp. 34°F - 40°F pressure dew point, 35 CFM, max. pressure PSIG 232 & 1/2" NPT air connection.

7 1/2 HP. electric motor, 200 gal. vertical tank, good condition

50HP Air Compressor 125PSI

Inovec Positioning & Control System. 30hp Electric / Hydraulic Power Unit to Run Log Knees with Salem Computerized Networks S/N 195839-03

INTERNATIONAL - 1295-44, ...Horizontal Closed Door BalerSpecifications: -- Cylinder: 7" -- Feed opening: 42" x 50" -- Main motor: 30 HP

INTERNATIONAL - 1295-44, ...Horizontal Closed Door BalerSpecifications: -- Cylinder: 7" -- Feed opening: 42" x 50" -- Main motor: 30 HP

INTERNATIONAL - IB-4430-60-HD, ...Automatic Tie Horizontal BalerSpecifications: -- Bale size: 44" x 30" -- Hopper opening: 42" x 60" -- Cylinder bore: 8" -- Cylinder stroke: 82" -- Tension cylinder: 6" -- Cycle time: 15 Sec (no load) -- Ram force: 150,800 Lbs -- Main motor: 40 HPEquipped with: -- Oil cooler

INTERNATIONAL - AT-4843-850-60, ...Auto-Tie Horizontal BalerSpecifications: -- Cylinder: 8" -- Opening size: 60" x 46" -- Main motor: 50 HPEquipped with: -- Control panel -- Oil Cooler: Air-Over-Oil -- 10' Bale Run-Out Table -- High temp/low oil level shutdown

INTERNATIONAL TITAN-60-EC Full Eject Horizontal Baler with ConveyorSpecifications: -- Cylinder: 8" -- Main motor: 20 HP -- Feed opening: 58"; x 35"; -- Bale Size: 60"; x 48"; x 30"; -- Feed conveyor width: 48" -- Ram face pressure: 3,000 PSI -- Total force: 150,800 Lbs -- Cycle time: 32 Sec (14 Sec short stroke)Equipped with: -- Programmable controller with Ethernet -- Conveyor controls and conveyor hopper

INTERNATIONAL TITAN 6-EC Closed Door Horizontal Baler with ConveyorSpecifications: -- Cylinder: 8"; -- Motor: 20 HP -- Cycle time: 32 Sec Cycle Time -- System pressure: 3,000 PSI -- Total force: 150,800 Lbs -- Ram face pressure: 87 PSI -- Feed opening: 58"; x 35"; -- Bale size: 60"; x 48"; x 30"; Equipped with: -- Feed conveyor: 48" wide -- Programmable controller -- Ethernet connection

INTERNATIONAL - MT-4843, ...Manual-Tie Horizontal Baler with Infeed ConveyorSpecifications: -- Cylinder: 8". -- Opening size: 60" x 46". -- Main motor: 40 HP.Equipped with: -- Control panel. -- Oil Cooler – Air-Over-Oil. -- 10' Bale Run-Out Table. -- High-Temp/Low Oil Level Shutdown. -- 48" x 43" x 60" Bale Size.

INTERNATIONAL - NA-1295HD, ...Closed Door Horizontal BalerSpecifications: -- Bale size: 72" x 44" x 36" -- Main cylinder bore: 8" -- Total force: 113,000 Lbs -- Ram face pressure: 71 PSI -- Feed opening: 42" x 50" -- Cycle time: 30 sec -- Main motor: 30 HPFeatures: -- PLC Control -- Bale table -- Shear bar -- Heavy-duty welded construction -- Heavy-duty hydraulic system -- Easy-to-operate controls

INTERNATIONAL BALER - IB-4430-50, ...Auto-Tie Horizontal BalerSpecifications: -- Cylinder: 8". -- Ram force: 125,660 Lbs. -- (6) Tension cylinders: 4" Bore. -- Feed opening: 42" x 50". -- Main motor: 40 HP.Equipped with: -- Shear blade with adjustable striker bar. -- Regin hydraulics. -- LED Indicators for bale functions. -- Autostart electronic beam. -- Oil cooler. -- Replaceable T-1 floor.NOTE: Ram needs some repair.

IBC - "IBC 4343 X 8 – 50 - 63": Horizontal Auto-Tie Baler -- Model: AT-4343-8-50-63. -- Type: Auto-Tie Baler. -- Motor: 50 HP. -- Cylinder Bore: 8";. -- Bale Size: 43"; x 43"; x Variable. -- Manufacturing Date: 2009.

IBC - NA-1296A-48: Horizontal Closed-Door Baler Model -- 50 HP Motor. -- Main Cylinder: 10″. -- Bale Size: 30″ x 45″ x 60″. -- Hopper Size: 57″ L x 45″ W. -- Platen Pressure: 134 PSI. -- System Pressure: 3,000 PSI. -- Total Force: 235,620 Lbs. -- New cylinder installed approximately (6) months ago.