Sawmill Equipment For Sale
.gif)
3831 Results Found
Call for Price
Model TC-710 - Single Phase Recycling Baler --The TC-710 Recycling Baler delivers over 45,000 lbs of crushing force featuring a 10 HP, 1 Phase electric motor. Each baler comes with an oil cooler and a 5″ diameter cylinder as a standard equipment. This mobile unit conveniently fits into a truck or trailer bed and can also be used curb-side or permanently installed in-plant. The TC-710 reduces aluminum cans or plastic bottles into a dense 20″ x 20″ x 36″ bale weighing approximately 150 lbs. --The small footprint makes it great for schools, hospitals, municipalities and breweries!Advantages of Baling --Bales can be easily stacked and stored for processing --Reduce waste cost disposal --Generate revenues from sales of bales
Call for Price
Turner Machinery Company Resaw Good Condition
Call for Price
4650# capacity @ 24" load center 188" max reach Sideshift Tilt 3388 hours on the meter
Call for Price
Call for Price
TYLER 2400 SLOT-WALL MACHINE: -- Specifications:Produces T-slot "slat-wall" for architectural/store fixtures. 4' x 8' (48" x 97") max. panel cap., 2' x 2' (24" x 24") min. panel cap., min. panel thickness = 0.5" max. panel thickness = 1.5"; The Tyler 2400 can machine up to (40) panels/Hr, depending on material density, thickness and the slot profile. -- Equipped with: (18) Router spindles all on 3" fixed centers, spindles are driven in groups of (3) with (6) 7.5 HP - 3,450 RPM motors, all router spindles rotate @ 15,400 RPM. -- Operation: Panels remain stationary on top, pneumatically clamped in place while the bottom mounted router bank traverses the full length of the panel with a high-speed return, variable feed speed control, router assembly traverses on ground & polished rails with chain drive. -- Panels are positioned along the 8' rear edge fence line, distance from the panel edge to the centerline of the 1st cut can be adjusted from 0.0" - 3" (1 router spindle pitch). -- Overhead hold-down assembly with (2) large air cylinders and (5) arms with spring loaded clamping pads hold the panel in place. Panels are loaded from the 8' front and exit to the side. -- Includes: Operator controls for the machine cycle and a "setup" mode of operation; machine cutting cycle is initiated by a 2-hand operator safety buttons located on the right front of machine. - Produces approx. (30 - 40) panels per hour. -- Available Options at Additional Cost:Router spindles on 4'- & 100-mm centers; 48" x 121" workpiece capacity increases left-to-right workpiece (length) capacity.60" x 97" workpiece capacity increases front-to-back workpiece (width) capacity & includes (1) additional multi-spindle router head.60" x 121" workpiece capacity increases front-to-back & left-to-right workpiece capacity & includes (1) additional multi-spindle router head.
Call for Price
Tyler Kerfsaver XL Resaw 1-1/4" Blades 36" Diameter Bandwheels Includes: Feed system that can tilt to mill tapered siding
Call for Price
Tyrone-Berry Carriage Feed Drive SMA-225 60-hp Electric Motor Included
Call for Price
Tyrone Berry 280C Shotgun Feedworks
Call for Price
Tyron-Berry SMA 215 Carriage Drive with Drum & Cable S/N 27440
TYRONE-BERRY Carriage feed, model 230 good condition with 125 HP motor on Hydraulic system and drum section. Drum has 20" x 20" face and grooved for 3/4" cable.
Call for Price
Tyrone Berry SMA 215 Carriage drive
Call for Price
Call for Price
Call for Price
Tyron Berry SMA 215E with Drum Package
Call for Price
Call for Price
Call for Price
Tyrone-Berry SMA 240 Carriage Drive
Call for Price
Tyrone-Berry SMA 215
Call for Price
Tyrone-Berry SMA 220
Call for Price
Tyrone-Berry Drum Package