Sawmill Equipment For Sale

12" capacity 25HP motor 460 volt 3-phase

2018 Baker Model C 4 Head Resaw Well maintained Work ready Only selling to go to a smaller unit SN 18-4895

1992 Baker 6 Head Resaw Six-Head "C" Saw 1 needs a spindle and wheel replacement. Approximately 8,320 Hours Serial Number 92-379 6 Motors (30) HP (37) Amps Mechanical Drive

1993 Baker 4 Head Resaw Approx. 50 blades Size: 13' 2" x 1" x .035" x 1/2" Tooth Carbon Resaw Blade Saw 1 needs a new spindle. Hydraulic drive. New Main Breaker New Fuses A couple of Starters have been replaced. Approximately 6,240 Hours Baker 4 Head Resaw Specifications Guide System: Baker Low-Profile Flat Guide System with steel guide plates for enhanced precision. Saw Dust Outlet: Dimensions: 6"x6" (15.24 cm x 15.24 cm) square. Outlet Adapter: 90° adapter chute to a 4” (10.2 cm) diameter outlet. Rotation: Can be rotated for discharge in four directions. Recommended Airflow: 600 CFM (17 m³/min). Motors: Main Motors: 20 HP, 3-phase motor on each head. Inline Hydraulic Pump Motor: Cutting Capacity: 6" x 12" (15.24 cm x 30.48 cm). Feed System (3-Sided Feed Works): Rough-top belting for traction. Powered side feed rollers for smooth material handling. Non-powered hold-over wheels. Feed Speed: Fully variable, adjustable from 20 to 120 feet per minute (6 to 36 meters per minute). Delivery is available at the buyer’s expense

Baker Dominator 3650E Sawmill Edmiston Edger Morbark Chipper with diesel engine All decks and rollers

Baker 2-Head Resaw 20 HP Motors Return Conveyor

Model 3650E with Baker (3) Strand Infeed Deck Excellent condition Hydraulic over electric general factory networks. Hooked up to power and ready to be demonstrated.

2 strand transfer deck, 28" wide x 14' long, #80 roller chain, no drive, good condition

Baker Short Log Circular Tri Scragg Mill

2008 Baker MDL BBR-O 2 HD Band Resaw S/N 08-4001

1995 Baker MDL BBR-O 3HD Band Resaw

Baker 4hd Bandsaw with complete run around. Located in WI. #C952

Baker A single Head Bandsaw with 18hp Kohler motor #00899

Large Sawmill Operation For Sale Located In East Texas in the Piney Woods, one of the densest forests in America, Custom Cut Lumber has been doubling its production every year for the past seven years last year we cut about 7 million board feet. The potentials are still yet much higher than that. Our crew varies from 35 to 50 men, depending on the season, and in the event of sale, most of these men would want to continue working on site for the new owner. We have developed into a number of niche markets that have served us well and the equipment here on the facility is equipped to produce a wide variety of products. One of the keys of our own success has been our diversified production. We have been able to shift production to supply different markets when the prices best served us. We cut for a variety of industrial applications: matt timbers, railroad ties, pallet material, dunnage, and a number of other products. We have built long term ongoing relationships with about 20 companies and hundreds of other individuals for whom we regularly cut orders. Our accounts receivable consistently receives payment from our customers over 33% faster than the national industrial average for our business type. We receive logs from about 20 local logging operations and companies in the east Texas area and the supply of pine, and mixed hardwoods including red and white oak, sweet gum, elm, ash, etc., is plenteous, along with regular and steady supplies of eastern aromatic red cedar, black walnut, hickory, etc. The mill is equipped with in-ground scales to weigh log trucks and tractor trailers, and an office building. There are 5 primary cut stations, including one with an end-dogging scragg mill with parallel 56” circle saw blades, dual vertical edgers, and a down feed green chain with a 4-head trim saw, a Baker 4-head resaw, and vertical bandsaw for trimming down sidecuts into pallet material. A cant breakdown station is equipped with a 2-head Baker split saw, a 5-head Newman trim saw, a Baker 5-head resaw, a notcher for runners/stringers, and stacking racks and belts for cutting and stacking pallet deck boards and stringers, with accompanying dust collection systems. In addition to the end-dogging Scragg mill, there is another Scragg mill station where we process slabs and smaller logs. There are two Baker 3630E Bandmill's with accompanying chop saws that we use to cut mat timbers, beams, dimensional lumber, slabs, mantles, etc., up to 32’ long and up to 30” wide. We have firewood splitters and stacking facilities as well, and a loading ramp for our woodchip markets. We have two 6,000 BDFT wood-fired kilns, numerous drying sheds, a mechanic’s bay with locking cargo container for valuables. There are two rental houses on the property, presently occupied by rent-paying occupants. There is a 30” Buss planer, a board edging station, two 48” chippers, Our support equipment includes 4 skid steers, 2 front-end loaders, one equipped with a

BAKER Model ABX Horizontal Band Resaw Like New BAKER Model ABX Horizontal Band Resaw S/N 08-397. 12” wide x 12” high cutting capacity with 30 HP 460 volts main motor with build in HPU unit has the optional outfeed rubber conveyor roll down to run thin material, the tilting feature to run bevels with the Smart Tool digital readout, and it has 12” wide x 86” long belt conveyor on the Infeed run of the machines HPU it is stand alone. Machine is on casters so it is easy to move in & out of position, it also has Easy Quick Change Electrical plugs. Includes lots of extra sawblades. Machine was built in 2007 and has not been used and stored inside. Dimensions machine: Length 84" x width x 72 1/2" x height 68" Weight 2000 lbs., Current new price prox $29,000. See photos of on our web site. Inventory No. KF2 .

Baker Furnace Inc Dry Kiln 3 phase 110V

Baker Furnace Inc Kiln 110V 3 Phase

Dry Kilns (cream), Conventional Heating System, 600,000 BTU Propane, single phase, 120V control voltage, 3 phase 208V motor voltage, open volume: 672 cubic feet, max operating temperature: 500F, owners manual included, excellent condition, 2 units available

BALEMASTER - 4550G-10: Auto-Tie Horizontal BalerSpecifications: --27"; x 40"; Opening. -- 50 HP. -- 10"; Cylinder. -- 30"; x 40"; x Variable Bale.

BALEMASTER - EO-650: Horizontal Auto-Tie Baler Specifications: • 25 HP Motor.• 8"; Main Cylinder.• Hopper Opening: 46";x 50";.• Bale Size: 48"; x 30"; x (variable).• Main Ram Face Pressure: 75 PSI.• System Pressure: 2,000 PSI.• Total Compression Force: 100,500 Lbs.