Sawmill Equipment For Sale
.gif)
3793 Results Found
Call for Price
Carthage Brunnette Machine 21" Ring Debarker 150' Per Minute put through.
$ 4,750
CAS (COMPRESSED AIR SYSTEMS) B73H84-E Reciprocating Air CompressorElite Series 7.5 HP 80 Gallon Horizontal Compressor @ 175 PSI / 24 CFMFeatures & Specifications: -- Access to Compressor Valves without Compressor Head Removal. -- All UL Electrical Controls -- ASME Tested Powder Coated Steel Tank. -- Auto Start / Stop. -- Bearings on Both Ends of the Crank Shaft. -- Centrifugal Unloader. -- Disk and Spring Valves. -- Fully Enclosed Belt Guard. -- Heavy-Duty Air Filter. -- Heavy-Duty (2) Stage Solid Cast Iron Pump. -- Industrial Grade Electric Motor. -- Magnetic Starter Mounted and Wired. -- Needle Bearings, and Inserts on Rods. -- Stainless Steel Flex Air Lines. -- Swedish Steel Valves. -- TEFC Drive Motor (3 Phase Only). -- Torrington Needle Bearings. -- 2-Grove B Width Motor Pulley. -- 2-Piece Tank Top Plate Design.Elite Compressor Features: -- All Basic Features. -- Automatic Tank Drain. -- Belt Guard After Cooler. -- Low Oil Monitor. -- Tank Discharge Ball Valve. -- Vibration Pads.
Call for Price
CASE W14 Wheel Loader with Bucket
Call for Price
Castaly Dowell Machine
$ 82,500
930K Caterpillar wheel loader, 2014 with 12798 hours, bucket and forks included located in Tazewell, VA Contact Zach Kittrell for more information. 931-224-0699 Well Maintained and ready to work for you.
$ 11,500
3 Phase.Year Model 93-97, 3306 Cat engine. 3171 hr. Everything works as it should. In good condition. Here is what you Need. Call for info 918-752-8142
$ 35,000
2002 Caterpillar 500 KW Generator 850 Hours Low Voltage Output Two Available
Call for Price
1997 CAT 400KW Diesel Gen Set w/3406 Engine & S/N 4ZR03246
$ 20,000
113 KW, 3 phase, 480 V, The engine is a year 2000. A New turbo the engine is a complete rebilt motor with no hr. after the rebilt. Call 440-313-8683
$ 14,900
Caterpillar Generator 40 KW Single phase Silent package 225 gallon fuel tank 554 hours Work ready
Call for Price
CATERPILLAR- XQ125, ...100KW DIESEL GENERATOROnly 50 hours!Specifications: --Diesel Generator --HP/KW: 100 kW --Caterpillar Model: XQ125 --Model Year: 2020 --Hours: 55 --Frequency: 60 Hz --XQ125 - C4.4 engine. --Rating - 125 KVA, --100 KW prime, 60 Hertz, 3 Phase, 12 wire.
Call for Price
6 Cylinder Cat Power Unit 3306 with Cat Power Take Off
Call for Price
1998 CAT 400KW Diesel Gen Set w/3406 Engine, 16,700 HRS & S/N 4ZR04721
$ 19,000
2015 P5000 Caterpillar Forklift, Hours 8102, Well Maintained! Located in Tazewell.VA. Contact Zach Kittrell for more information. 931-224-0699
Call for Price
2004 800KW Cat Gen Set S/N 00000TTFT00197. 12,700 Hrs
$ 14,900
CAT Generator, Ref# 138 Call Amy for Details 928-723-9449
CEFLA TNS 6000 Rubber Belt Transfer Conveyor 216"; long x 74 1/4"; wide (66"; wide belt) -- 3PH motor --Adjustable height feet
Tool Grinding Machine for V-Type Gouges. -- Tabletop design saves space. -- Works with most sizes of v-gouges. -- Optional standing base $275.00. -- Diamond stone cutting wheels, ordered seperately, price $420.00 each. -- Please specify required voltage and lathe model when ordering wheels.
Call for Price
CFORM Edger/Rip Saw - model CKM160 This machine was purchased new and installed the beginning of 2023. It has less than 20 hours. The seller changed applications. Machine is ready to load. Photos coming! Manufacturer information: Double Edgeing & Slicing Cutter the value of lumber with clean edges can often exceed the value of rough-cut boards. In one pass, this Twin Blade Board Edger takes boards fresh off the mill and turns them into clean, square edged lumber. This edger is easy to use, with one fixed blade and one moveable blade that adjusts with a manual dial. Easily select the precise size of lumber you need. Lower the perimeter fence when you need to edge only one side of a board. Features: Movable finger iron platers for safe guidance and protection. Maximum 15 raws circular saws, adjustable distances. Hydraulic upper roller pressure and movable cyclinders. Maximum cutting height (inch)6 5/16?, 4 11/16?
Call for Price
Challenger Grinder with 10' Infeed Steel Belt, On Board Hydraulics.