Sawmill Equipment For Sale

30” x 165’ Concave Belt, Conveyor/Shaft Mount Drive

30' Concave Belt Conveyor with 24" belt

32" Concave Belt Conveyor

7,000 Square feet of cloth Approx 70,000 CFM (2) 37" Positive Fans: 150 and 125 HP Ready to load on your truck!

CONCEPT-AIR "S12" Primary Filter Bag House Dust Collector System complete with the following components and features: -- Fan model HDR32 (CONCEPT AIR) belt driven with 100 HP Drive Motor -- Material Discharge Screw Conveyor Followed by a Rotary Air Lock. -- Return Air with summer/winter diverter. -- Shell is 12' dia. and houses (xxx) Size 8" x 120" Filter Bags for a total of x,xxx sq/ft Filter Cloth. Cleaning is with shaker system?. -- (4) Door Explosion Venting. -- Support Structure. -- Catwalk with Access Ladder. -- Professional removal and loading is available. -- NOTE: More information to follow.

750 kw Generator This was owned by a hospital. Seller purchased both units and never used them.

PRICED REDUCED Cone 2-Saw Independent Arbor Optimized High Speed Edger, 4/4 to 4" runs 14 boards per minute W/ Tailing Device W/ Innovec Generation III Controls W/ Lots of Spare Boards & Parts to Keep Software Running, Includes MIC Unscrambler, with even ender up top. Scanning Bar and hi-speed indexible infeed and tailing belt outfield. On the ground and ready to load. Taken out with Videos and instructions to re-install. A must. Ref #131

Hydraulic Power pack with 2 Hydraulic pumps 30hp & 7 1/2hp, oil cooler & Accumulator 30 HP & 7 1/2HP pumps 30 HP Continental Pump 3,500 PSI ( 241 bar), disp 2.62 in3/rev. P/N: 259012 / HPV-20B35-RF-O-1R-B VELJAN 7 1/2HP pump with Baldor 7 1/2hp, 2HP Baldor motor oil cooler Contact us for a delivered price Wooden pallet/crate will be provided for shipping

Hydraulic pump power unit, 3500 psi, 29 GPM. 100 gallon tank, 30 hp Continental Pump model: HPVR-29B35-RF-O-1R-A 100-gallon Tank MFG: HTS/Hydraulic Technical Service, Eugene OR. Hydraulic power pack 3,500 psi. Pump P/N : 1021823 Pump Disp. 3.97 in3/rev 3500 PSI max pressure, GPM: 29/30? 4 Nachi Solenoid hydraulic valves 30 HP Toshiba motor: 230/460,1770 RPM, Frame 286TC, TEFC, Duty Cont., Inverter Duty, VPWM, Severe Duty, Ins. F., Date: 2014 on tank Tank Heater: Watlow, 1ph, 1500 Watts, 240/480 volt, Prior use and stored inside a building. Approximate Shipping dimensions: 54”W x 54” L x 84” tall, 1,900 LBS. a pallet/crate will be built at NO cost for shipping, tank has been drained of oil. Contact us for a shipping rate

Continental Automatic Gas Fired Boiler S/N L 196710

Cooks edger, 6" thick x 36" wide capacity, 2 movable blades, set up for tailing belt, hyd drive, includes controls, tailing belt, dust auger under edger, nice condition and ready for production

COOK 2 SAW EDGER-BOTH SAWS SLIDE W/9' INFEED ROLLCASE, 20HP MTR & 7 1/2 MTR S/N 3682981

Cook 6" x 48" 2 Saw Edger. W/ in & out feed.

MLS Number 11413038 Cooper Overhead End Dogging Scragg With Debarker And Gang Edger Transfer Chain Conveyor x 60’, H82,1-7.5 HP 480V gear drive 54" Cut Off Saw, 20 HP 480V motor, hyd stop gates, 20 HP hyd pack 4 strand x 12' long Debarker In Feed Deck, 5 HP 480V gear drive, H78 16” wide x 19’ long log haul belt conveyor (driven from debarker in feed tire drive) Cambio 24" Debarker, 75 HP 480V drive, spiked in/out feed rolls 20 HP 480V drive 3’ wide x 36’ long hour glass rolls transfer, 7.5 HP 480V gear drive 5-strand Scragg in feed deck x 20', H82, hyd log stop loader, 7.5 HP 480V gear drive Cooper Overhead Scragg Mill, 30 HP 480V 150 gal hyd package, variable speed cable drum feed works with pantograph arm Log positioning rolls on infeed w/ double overhead dogging system, 48” dia. saw husk(125 HP 480V each saw), setworks control 2-18” wide 2-position slab and side board belt conveyors, operators control cab w/ controls, camera and monitor for centering log 8-16’ length capacity, maximum log dia. 22”, largest square cant 12” x 12”, smallest square cant 4” x 4” 5-strand lower camel back landing transfer x 9’-6” long, 4-strand hyd lift transfer to gang edger and cant center bypass Center bypass rolls and belt conveyor to edger out feed landing transfer 10” mainland gang edger w/ 200 HP 480V drive,34” inserted tooth saws with 5/16” kerf(24 spare saws with collars), 2-2-2-4 spacing 6” x 50” mainland board edger w/ 150 HP 480V electric drive, 24” inserted tooth saws with 5/16” kerf, 8”-4”-4”-10”-6” pockets, 7-individual actuated self tailing belt conveyor out feed c/w splitters Camel back transfer,4-strand x 27-1/2’ long, H78B, 5 HP 480V gear drive 2-Saw Trimmer, 4-strand x 10’ long, 16’-4” between 20” dia. saws,10HP 480V drive on feed works and saws, 16” wide x 28’ long out feed belt conveyor, 5HP 480V gear drive 4-strand x 26’ long H78 camel back transfer w/ 5HP 480V gear drive

1988 Cooper End Dogging Scragg Mill with 48" Diameter Blades & 125HP Motors S/N CM-6076. Out and ready to go.

2004 Cooper 16ft Enddogging Scragg S/N CM-6181

Complete mill that needs to be removed from the current location. Seller will not split up the operation. (2) Infeed Decks: - (2) 3-Strand Infeed Deck 24' Long - H82 Chain - 3-7/16" Shaft - (2) 10 HP Drives - 3-Strand infeed deck 60' Long Cut Off Saw: - 54" Saw - 20 HP Motor - Hourglass rollers - Hydraulic length stops - Diverter gate to debarker Debarker - Infeed Deck - Cambio 24" Debarker - 75 HP Main motor Scragg: - 5-strand Infeed, 20' Long - Copper Scragg: 30 HP Hydraulic package, variable speed cable feed works with pantograph arm, log positioning, 48" saws with 125 HP motors, (2) 18" 2-position slab conveyors, cab, 8'-16' length capacity, max log 22", largest cant 12"x12" - Outfeed sorting system to two edgers: 5-Stand lower deck, 4-strand hydraulic lift to gang edger Gang & Board Edger: - 10" Mainland Gang Edger: 200 HP Motor, 34" inserted tooth saws with 5/16" kerf - 6" x 50" Mainland Board Edger: 150 HP motor, 24" blades, self tailing outfeed conveyor Trim Saw: - 2-Saw Trimmer with outfeed Greenchain: - Camel Back Landing Transfer - 4-Strand x 26' Long - 4-Strand: 8'4" Decline transfer - 4-Strand 66' Greenchain

COOPER Dropsaw Trimmer - 24' left hand trimmer. Cuts up to 8" thick and 24 feet long. 15 hp saw motors. Zero saw adjustable for desired overtrim. Saws every 2 feet from 6 to 24 feet. 11 lugged feed chains with even-ender. Hydraulic variable speed feed. Controls and console remain wired. Over dimensional for transporting 32' long x 11.5' wide x 10'3" tall.

Cor Dus 12" x 5' Belt conveyor

Cor-Dus Custom Belted Live Rolls 12" x 12.5' With Motor and Drive.