Sawmill Equipment For Sale

- Close link chain vs. open (no dust or pinch point) - Oiler has twice the number of lube points (critical) - The VS adjustment location on the 14N. - Can cut up to 4 15/16? with 14? blade vs. the MRS-12 12? blade 3-15/16”. - Can run 12? as well on the MRS-14N - Bottom kickback fingers for added safety - Saws, with proper tooling and material, can glue line Specifications: - Main Motor Hp. = 50 Hp. - Voltage/ Freq. = 460 Volt 60Hz - Phase = 3 Phase - Amp Requirement = 35 Amps - Feed Hp. = 2 Speed 1.5 / 3 Hp. - Feed System = Feed Chain - Feed Speed = 25 – 120 FPM - Variable Speed = Variable Speed Pulley - Elevation Hp. = 1/4 Hp. - Elevation Style = Manual Wheel Adjustment - Elevation Sys. = Jack Screw / Linear Guides - Total Hp. = 53.25 Hp. - Electronics = CE Approved Components - Dual Voltage = Elevation Arbor Motors - Control Voltage = 110 Volt - Assisted Start = Wye-Delta - Pass-Line = 33-1/2” - Min. Length = 17-3/4” - Min. Width = 1/2” - Max. Width = 27-1/8” - Min. Thickness = 5/16” - Max. Thickness = 4-15/16” - Arbor Rpm = 3570 Rpm - Blade Size = 12” Tungsten Carbide Tipped - No. of Teeth = 36 Tooth - Blade Kerf = 3.5 mm - Cleaning System = Brush on Chain - Vertical Travel = 3/8” – 5” - Dust Collection = (2) 6” @ 1962 CFM - Arbor Diameter = 70 mm - Hold Down Style = Pressure Plate - Kickback Finger = (2) Top (1) Bottom Sets - Emergency Stop = Push Button - Rear E Stop = Push Button - Safety Feature = Safety Interlock Switch - Guarding = Full Cabinet Enclosure - Oiler = Automatic Mechanical Oiler - Low Oil Warning = Low Oil Shut-off - Fence Type = Adjustable - Fence Dims. = 103” Length - Frame Const. = 5/16” Steel Construction - Worktable Dims. = 27-1/8” x 64” - Infeed Table = 13-3/4” x 103” - Decible Rating = 74 dB - Net Weight = 4402 Lbs. - Gross Weight = 4694 Lbs. - Machine Dims. = 67” x 58” x 71” - Packaging Dims = 72” x 65” x 77”

16 HP 12 filter bags up 4 collection bags lower Lots of pipe

NOVA TTF-6200 Dry Kiln System; Unassembled Front Load Kiln Designed to hold 5,100 bd. ft 4/4 Lumber, or 6,120 bd. ft 8/4 Lumber, Using 3/8" (9 mm) stickers. -- Specifications: Interior Dimensions: H 10' 3,5" (3.14 m), D 7'2"(2.19 m), W 25' 3" (7.7 m). -- Loading Door Opening: H 9' 10" (2.85 m), W 25' 3" (7.7 m). 1/8 " Aluminum sidewall bumpers, side hinged doors, exterior installation. -- Average 4/4 capacity: 5,100 bd. ft (12 m3) with 3/8" (9 mm) stickers. -- Average 8/4 capacity: 6,120 bd. ft (14 m³) with 3/8" (9 mm) stickers. -- Price shown is for kiln only. -- High horsepower heat requirement: 128 k BTU/hour. -- Heated Floor System, manuals and blueprints. -- Electrical Requirements: 230 VAC, 1 Phase, 60 Cycle, 25 kw/Hr max.

(2) Unassembled front load Kilns only System with high HP heat and exhaust designed to hold 8,461 bd/ft (20 cub.m) of 3/4" (25 mm) lumber and 10,475 bd/ft (25 cub.m) of 8/4" (50 mm) lumber (35 cbm). -- Kilns internal dimension: Height 12'3-1/2" (3.75 m), Depth 16' (4.88 m), Width 21' (6.4 m). -- Loading door opening of 10' (3.05 m) x 21' (6.4 m); 1/8" aluminum side wall bumpers, side hinged doors, exterior installation. -- High HP will service the heat requirements up to 245k BTU/Hr. -- Electrical requirement of 230 VAC, 3-Phase, 60 Cy; 7.21 kW/Hr. -- System includes: Timber Dry management automated Dry Kiln Controls for each kiln, touch-screen operator interface, data recording, optional remote access, and networking capability, Replacement part kit for a kiln. Manuals & Blueprints

Unassembled Front Load Kiln with Standard Heat and Exhaust -- Interior dimensions: H 17' 6" (5.33 m), D 25' 8" (7.8 m), W 26' (7.9 m). -- Loading Door Opening: height 14'6" (4.4 m), width 25'3" (7.7 m). 1/8" Aluminum Bumper Walls, Top Hinge Door, Exterior Installation. -- Average 4/4 capacity: 25,459 Bd Ft. with 3/4" stickers. Average 8/4 capacity: 33,293 Bd Ft with 3/4" stickers. -- Price shown is for kiln only. -- Standard HP Heat requirement: 382k BTU suitable for drying dark hard woods; Optional high HP Heat requirement: 674k BTU suitable for drying softwood and white hardwoods. -- Electrical requirements: 480 VAC, 3 Ph., 60 Cy; 16.5 kW/Hr. Timber Management Control System with touch screen operator interface, data recording, remote access & networking capability. -- Features: Control room with heated air intake; 12'H x 4'D x 26'W. Top Hinge door opening System includes "230" electric chain hoist. Boiler Room: 12' W x 25' D x 17'6" H. 10' roll up & (1) access door. - Timber Dry Management Network Capability.

Nyle Kiln L300 - L300 Nyle high temperature Lumber drying Kiln - 240v single phase. Capable of temps up to 160 degrees. - Bought new in 1999 Call 800-459-2148 for more info.

Nyle Firewood Dry kiln No chamber included

Nyle PHT350 Kiln System was powered up and tested, but not put into production.

OGAM Gang Rip 30HP Motor w/electrical still Hooked Up, Model PO 195, S/N 15149

30 brand new Oleson 10" double cut band blades. Entire lot for $20,000.00. Individual blade $1,175.00. Buyer pays for shipping. Call 800-459-2148 for more info.

Oliver Sawmill New Carriage Wheels New battery

ONEIDA AIR SYSTEMS XXK200300 Cyclone Dust Collector w/ Rotary Air Lock: Cyclone & Fabric Filtration Dust Collection System. -- 3,800 CFM @ 12" SP to 6,800 CFM @ 2.7" SP with 20 HP Baldor Class F, TEFC motor with 1.15 service factor. -- High efficiency 12-gauge cyclone barrel with fully seam-welded construction. Powder coated paint finish, weather-proof cyclone and fan blower. -- (4) High Efficient Axtar Spun-Bonded Media cartridge after-filters for 620 sq. ft. of filter media with inverted plenum. Filters 99.9% efficient of 0.2 - 2.0 microns, Teflon-like coating to facilitate dust cake release. -- Fan is welded carbon steel, backward incline, dynamic, two plane balanced. Same as aircraft turbine rotors. -- 16" Rectangular Inlet with square to round inlet adapter. -- Includes: Freestanding Leg Kit with Rotary Airlock, magnetic starter, internal silencer reduces sound to 82 dB @ 10'. MADE IN THE USA.

ONEIDA AIR SYSTEMS XXK050346 Cyclone Dust Collector w/ After-filter Plenum. Cyclone & Cartridge Fabric Filtration Dust Collection System for High Pressure CNC applications (need more static pressure for effective cleaning of cutter heads). -- Performance: 2,120 CFM @ 2" SP with Filter. 5 HP US Made BALDOR , Class F, TEFC motor. Magnetic Starter w/ on-off switch and overload protection. -- Fan/Wheel housing: Extremely strong cast aluminum, non-sparking (per NFPA fire code). Efficient Backward Inclined high performance and low noise. No rivets or welds. Fully welded fan housing 11 ga. Motor Housing plate. Includes: -- Cyclone: (8") solid welded inlet with Neutral Vane. Technology reduces filter maintenance. 16-gage cyclone barrel with solid welded construction. Rectangular outlet cam be rotated independent of inlet - 8-bolt patterns. Outlet is 10.03" x 7.64" inside dimensions. Square to round adaptor available. Approx. 26" dia. cyclone housing. -- After-filter plenum for (10) filter bagsDust collector is missing cyclone stand and filter bags. .

7.5 HP single phase cyclone/dust collection assorted dust pipe and fittings as pictured

ONEIDA AIR SYSTEMS XXK10 Cyclone Dust Collector w/ After-filter and Drum: Cyclone & Fabric Filtration Dust Collection System.Specifications: -- 3,800 CFM @ 2.3" SP with 10 HP US Made, Class F, TEFC motor with 1.15 service factor. -- High efficiency 12-gauge cyclone barrel with fully seam-welded construction. Powder coated paint finish, weather-proof cyclone and fan blower. -- (3) High Efficient Izumi Axtar Spunbond Media cartridge after-filters for 465 sq. ft. of filter media. Filters 99.9% efficient of 0.2 - 2.0 microns, teflon-like coating to facilitate dust cake release. -- Impeller is 17" Diameter, Single-piece, backward inclined, non-sparking/non-ferrous, cast aluminum alloy. -- Inlet size 12" round. outlet 12.5" x 10" square dia. -- Includes: Heavy Duty angle iron stand, magnetic starter, and (1) 55 gal. drum kit for waste collection. MADE IN THE USA..

ONEIDA AIR SYSTEMS SAZ10000C Rotary Air LockONEIDA Air Locks use a high-efficiency helical drive, US-made 0.25 HP hollow shaft gear motor to control the flow of discharge material from the dust collector via a rubber-padded wheel that rotates at a preset speed. The airtight seal with the collector is maintained at all times, ensuring peak airflow performance while waste is continuously deposited into open bins, industrial hoppers, or transfer blower systems.Specifications: -- 10" Dia. flange ideal for use with many of our professional and industrial systems, including the High Vacuum dust collector (with custom clean-out cone). -- US-made 0.25 HP hollow shaft Helical gear motor. -- Impeller Type, welded steel with industrial, replaceable rubber paddles. -- Inlet/outlet 10" round. -- Designed for wood and other non-explosive dust only; not intended for severe duty.

ONEIDA AIR SYSTEMS XXK050346 Cyclone 'High Vacuum' Cartridge Filter Dust Collector w/ One Drum: Cyclone & Cartridge Fabric Filtration Dust Collection System for High Pressure CNC applications (need more static pressure for effective cleaning of cutter heads). -- Performance: 2,120 CFM @ 2" SP with Filter. 5 HP US Made BALDOR , Class F, TEFC motor. Magnetic Starter w/ on-off switch and overload protection. -- Fan/Wheel housing: Extremely strong cast aluminum, non-sparking (per NFPA fire code). Efficient Backward Inclined high performance and low noise. No rivets or welds. Fully welded fan housing 11 ga. Motor Housing plate. -- Cyclone: (8") solid welded inlet with Neutral Vane. Technology reduces filter maintenance. 16-gage cyclone barrel with solid welded construction. Rectangular outlet cam be rotated independent of inlet - 8-bolt patterns. Outlet is 10.03" x 7.64" inside dimensions. Square to round adaptor available. Approx. 26" dia. cyclone housing. -- Efficient Filter Cartridge For 155 sq. ft. of filter media. Filters 99.9% efficient of 0.2 - 2.0 microns @ 11 FPM , wide pleated spacing and teflon-like interior coating for easy dust release. Filter size: (1) 18" x 39" & (1) 18: x 19.5". Filter Grounding Wire. -- Includes: Filter Efficiency Gauge. Built-in Silencer reduces sound to 75-81dBA @10' . One 55 Gallon Steel Drum. Top seal cover and flexible connection to cyclone discharge. Angle iron support stand w/leg extensions. -- Dimensions: 31" x 59" x 109.5".Available Options;Bag Gripper, Plastic Bag Hold-Down SystemHoppers / Multiple DrumsBin Level IndicatorRotary AirlockRemote Starter - Radio Frequency - 1 Phase onlyGE HEPA (H-12) Filter Media)Available with 600 Volt motor.

ONEIDA AIR SYSTEMS XXK070323 Cyclone Dust Collector w/ Rotary Air Lock: Cyclone & Fabric Filtration Dust Collection System.Specifications: -- 2,900 CFM @ 1.5" SP with 7.5 HP US Made, Class F, TEFC motor with 1.15 service factor. -- High efficiency 12-gauge cyclone barrel with fully seam-welded construction. Powder coated paint finish, weather-proof cyclone and fan blower. -- (2) High Efficient Izumi Axtar Spunbond Media cartridge after-filters for 310 sq. ft. of filter media. Filters 99.9% efficient of 0.2 - 2.0 microns, Teflon-like coating to facilitate dust cake release. -- Impeller is 16.5" Diameter, Single-piece, backward inclined, non-sparking/non-ferrous, cast aluminum alloy. -- Inlet size 10" round. outlet 12" round dia. Includes: -- Rotary Air Lock, magnetic starterOptions: -- Freestanding Leg Kit with Dual 55-Gallon steel drum less Rotary Air Lock...as for pricing. MADE IN THE USA.(Actual P/N XXK070323-460-AIR).

ONEIDA AIR SYSTEMS FXK041500 Cyclone Dust Collector w/ After-Filter Plenum: Cyclone & Fabric Filtration Dust Collection System. -- 3,800 CFM @ 12" SP to 6,000 CFM @ 2.7" SP with 15 HP Baldor Class F, TEFC motor with 1.15 service factor. -- High efficiency 12-gauge cyclone barrel with fully seam-welded construction. Powder coated paint finish, weather-proof cyclone and fan blower. -- (4) High Efficient Izumi Axtar Spunbond Media cartridge after-filters (hanging) for 620 sq. ft. of filter media. Filters 99.9% efficient of 0.2 - 2.0 microns, Teflon-like coating to facilitate dust cake release. -- Fan is welded carbon steel, backward incline, dynamic, two plane balanced. Same as aircraft turbine rotors. -- Inlet size 14" round. outlet 16" round dia. -- Includes: Heavy Duty angle iron stand, magnetic starter, internal silencer reduces sound to 85-87 dB @ 10'Includes Rotary Air-lock for dumping into a waste bin!MADE IN THE USA.

ONEIDA AIR SYSTEMS XXK10 Cyclone Dust Collector w/ Rotary Air Lock: Cyclone & Fabric Filtration Dust Collection System.Specifications: -- 3,800 CFM @ 2.3" SP with 10 HP US Made, Class F, TEFC motor with 1.15 service factor. -- High efficiency 12-gauge cyclone barrel with fully seam-welded construction. Powder coated paint finish, weather-proof cyclone and fan blower. -- (3) High Efficient Izumi Axtar Spunbond Media cartridge after-filters for 465 sq. ft. of filter media. Filters 99.9% efficient of 0.2 - 2.0 microns, teflon-like coating to facilitate dust cake release. -- Impeller is 17" Diameter, Single-piece, backward inclined, non-sparking/non-ferrous, cast aluminum alloy. -- Inlet size 12" round. outlet 12.5" x 10" square dia. -- Includes: Heavy Duty angle iron stand, magnetic starter, and Rotary Air Lock. MADE IN THE USA..