Sawmill Equipment For Sale

32" Concave Belt Conveyor

7,000 Square feet of cloth Approx 70,000 CFM (2) 37" Positive Fans: 150 and 125 HP Ready to load on your truck!

750 kw Generator This was owned by a hospital. Seller purchased both units and never used them.

PRICED REDUCED Cone 2-Saw Independent Arbor Optimized High Speed Edger, 4/4 to 4" runs 14 boards per minute W/ Tailing Device W/ Innovec Generation III Controls W/ Lots of Spare Boards & Parts to Keep Software Running, Includes MIC Unscrambler, with even ender up top. Scanning Bar and hi speed indexible infeed and tailing belt outfield. On the ground and ready to load. Taken out with Videos and instructions to re-install. A must.

Continental Automatic Gas Fired Boiler S/N L 196710

Hydraulic pump power unit, 3500 psi, 29 GPM. 100 gallon tank, 30 hp Continental Pump model: HPVR-29B35-RF-O-1R-A 100-gallon Tank MFG: HTS/Hydraulic Technical Service, Eugene OR. Hydraulic power pack 3,500 psi. Pump P/N : 1021823 Pump Disp. 3.97 in3/rev 3500 PSI max pressure, GPM: 29/30? 4 Nachi Solenoid hydraulic valves 30 HP Toshiba motor: 230/460,1770 RPM, Frame 286TC, TEFC, Duty Cont., Inverter Duty, VPWM, Severe Duty, Ins. F., Date: 2014 on tank Tank Heater: Watlow, 1ph, 1500 Watts, 240/480 volt, Prior use and stored inside a building. Approximate Shipping dimensions: 54”W x 54” L x 84” tall, 1,900 LBS. a pallet/crate will be built at NO cost for shipping, tank has been drained of oil. Contact us for a shipping rate

Cook's AC36 - Fully Hydraulic - Perkins 400 C Series 65 HP Engine - Engine has been serviced with new filters. - Starts easily and runs well - New fuel tank. New hydraulic tank. Hydraulic pump rebuilt. New idle wheel. Idle wheel tensioner replaced with all new factory parts Call 800-459-2148 for more info.

Cook's HD-32 Manual Band Sawmill - 2022 Cook's HD-32 thin kerf sawmill package #3 - 25 HP Kohler engine with just over 1 hour on the mill - Cap 16' x 32" - 12 V loading winch with ramps - Trailer with spare tire - 12 V head up/down - Includes: 10 new super sharp blades, metal cant hook, blade alignment tool, stainless steel bunks, 10 new blades, 5 gallons on copper naphthenate concentrate for treating lumber, Solar trickle charger for winch - Mill can be towed distances with ease - Weighs approx 2500 # Call 800-459-2148 for more info.

Cooks edger, 6" thick x 36" wide capacity, 2 movable blades, set up for tailing belt, hyd drive, includes controls, tailing belt, dust auger under edger, nice condition and ready for production

Cook's 2019 AC 36 Fully Hydraulic Band Sawmill - 67 HP Yanmar Diesel - Computer Setworks - Debarker/Mudsaw - Remote Engine Shutdown and Throttle Control - Mega Guide System - 26" All Metal Bandwheels - Gearbox Head Raising System - Dual Axles with Brakes. - 14" Split Strobe Saws - Trailer Package - Cat Claw Dual Tooth Setter - Cat Claw Sharpener - Mega Parts Package:? (60) Super Sharp™ Blades (4) Spare 2" Guides (10) Replacement Guide Bearings (2) Spare Drive Belt (2) Spare Pump Belt (2) Sharpener Grind Rocks (1) Metal 4ft. Cant Hook (1) Timberjack (1) Hand Set Checker (1) Blade Alignment Tool (1) Spare Tire 2019 Model 871 Hours on Saw - Has Bill of Sale Call 800-459-2148 for more info.

COOK 2 SAW EDGER-BOTH SAWS SLIDE W/9' INFEED ROLLCASE, 20HP MTR & 7 1/2 MTR S/N 3682981

Cook 6" x 48" 2 Saw Edger. W/ in & out feed.

Coollair Model SPL-CBY72N.1Exhaust / Intake Fans - 72" - 2 HP, Belt drive Industrial/Commercial Heavy Duty Panel Axial Exhaust Fan Estimated Dimensions 80" x 80" Each heavy duty all welded structural frame, heavy duty self aligning ball bearing pillow blocks, heavy duty V belt drive with cast iron sheaves, 8 Blades Baldor M3558T AC Motor 2HP 208-230/460V 1725 RPM 3 Phase Frame 145T 3PH 60Hz TEFC Belt Size (Qty 2) BX 88 GREENHOUSE FANS, ARGICULTURAL , WAREHOUSE , HEAVY DUTY , https://www.coolair.com/ Call 800-459-2148 for more info.

Log Merchandising Saws $10,000. 72” Carbide Tipped Blade 75 HP Motor. Air Cylinders To Move Blade.

MLS Number 11413038 Cooper Overhead End Dogging Scragg With Debarker And Gang Edger Transfer Chain Conveyor x 60’, H82,1-7.5 HP 480V gear drive 54" Cut Off Saw, 20 HP 480V motor, hyd stop gates, 20 HP hyd pack 4 strand x 12' long Debarker In Feed Deck, 5 HP 480V gear drive, H78 16” wide x 19’ long log haul belt conveyor (driven from debarker in feed tire drive) Cambio 24" Debarker, 75 HP 480V drive, spiked in/out feed rolls 20 HP 480V drive 3’ wide x 36’ long hour glass rolls transfer, 7.5 HP 480V gear drive 5-strand Scragg in feed deck x 20', H82, hyd log stop loader, 7.5 HP 480V gear drive Cooper Overhead Scragg Mill, 30 HP 480V 150 gal hyd package, variable speed cable drum feed works with pantograph arm Log positioning rolls on infeed w/ double overhead dogging system, 48” dia. saw husk(125 HP 480V each saw), setworks control 2-18” wide 2-position slab and side board belt conveyors, operators control cab w/ controls, camera and monitor for centering log 8-16’ length capacity, maximum log dia. 22”, largest square cant 12” x 12”, smallest square cant 4” x 4” 5-strand lower camel back landing transfer x 9’-6” long, 4-strand hyd lift transfer to gang edger and cant center bypass Center bypass rolls and belt conveyor to edger out feed landing transfer 10” mainland gang edger w/ 200 HP 480V drive,34” inserted tooth saws with 5/16” kerf(24 spare saws with collars), 2-2-2-4 spacing 6” x 50” mainland board edger w/ 150 HP 480V electric drive, 24” inserted tooth saws with 5/16” kerf, 8”-4”-4”-10”-6” pockets, 7-individual actuated self tailing belt conveyor out feed c/w splitters Camel back transfer,4-strand x 27-1/2’ long, H78B, 5 HP 480V gear drive 2-Saw Trimmer, 4-strand x 10’ long, 16’-4” between 20” dia. saws,10HP 480V drive on feed works and saws, 16” wide x 28’ long out feed belt conveyor, 5HP 480V gear drive 4-strand x 26’ long H78 camel back transfer w/ 5HP 480V gear drive

Cooper 16' End Dogging Scragg with Cab & Controls Out & Ready to Ship. Located in Henry TN.

2004 Cooper 16ft Enddogging Scragg S/N CM-6181

Cooper 18' Enddogging Scragg Mill

COOPER Dropsaw Trimmer - 24' left hand trimmer. Cuts up to 8" thick and 24 feet long. 15 hp saw motors. Zero saw adjustable for desired overtrim. Saws every 2 feet from 6 to 24 feet. 11 lugged feed chains with even-ender. Hydraulic variable speed feed. Controls and console remain wired. Over dimensional for transporting 32' long x 11.5' wide x 10'3" tall.

Complete mill that needs to be removed from the current location. Seller will not split up the operation. (2) Infeed Decks: - (2) 3-Strand Infeed Deck 24' Long - H82 Chain - 3-7/16" Shaft - (2) 10 HP Drives - 3-Strand infeed deck 60' Long Cut Off Saw: - 54" Saw - 20 HP Motor - Hourglass rollers - Hydraulic length stops - Diverter gate to debarker Debarker - Infeed Deck - Cambio 24" Debarker - 75 HP Main motor Scragg: - 5-strand Infeed, 20' Long - Copper Scragg: 30 HP Hydraulic package, variable speed cable feed works with pantograph arm, log positioning, 48" saws with 125 HP motors, (2) 18" 2-position slab conveyors, cab, 8'-16' length capacity, max log 22", largest cant 12"x12" - Outfeed sorting system to two edgers: 5-Stand lower deck, 4-strand hydraulic lift to gang edger Gang & Board Edger: - 10" Mainland Gang Edger: 200 HP Motor, 34" inserted tooth saws with 5/16" kerf - 6" x 50" Mainland Board Edger: 150 HP motor, 24" blades, self tailing outfeed conveyor Trim Saw: - 2-Saw Trimmer with outfeed Greenchain: - Camel Back Landing Transfer - 4-Strand x 26' Long - 4-Strand: 8'4" Decline transfer - 4-Strand 66' Greenchain