Sawmill Equipment For Sale
.gif)
3832 Results Found
.jpg?width=220&height=170&mode=crop)
$ 2,500
Hyd-car Hoist, will go up approx 16' with 30 HP pub, 3 phase. Call 800-459-2148 for more info.
$ 750
$ 3,800
Kewanee Boiler 32 HP with 12000 burner Call 800-459-2148 for more info.
$ 4,000
White Kohler Gensets, 120-208 46 KW, KVH 56-22. 150 amps. Call 800-459-2148 for more info.
Teco Induction Motor. Type AEEFFB-SJ7 Frame, 132M 15 HP RPM 3540 Volts 230/460 3 Phase. This electric motor was taken NEW off a LeaderMac 523 SpeedMac. Call 800-459-2148 for more info.
Teco Induction Motor, Type AEVFFB-SJA, 15 HP, RPM 3500 Volts 230/460 3 Phase. This electric motor was taken NEW off a LeaderMac 523 SpeedMac Call 800-459-2148 for more info.
$ 5,000
Cyclone and Storage Bin Approximate Capacity 250 Cubic Yards Approximate Overall Height 55 feet Storage Bin 18 feet in diameter Call 800-459-2148 for more info.
$ 5,000
Sawdust conveyor - 45' x 12" Single chain with rubber boots to move your material. There is UHMW plastic wear plate on the top and bottom. Call 800-459-2148 for more info.
$ 5,000
Circlular Sawmill 48" blades, 2 are new. Call 800-459-2148 for more info.
$ 1,750
VM higher hour diesel engine. 4 cylinder, 1800 rpms, 35 HP, Skid mounted, low profile. Does not have control, clutch, or air cooler. Call 800-459-2148 for more info.
$ 7,000
70 feet of live rollers (needs motor): 10' sections that can be interlocked to be as long as you want, 5 HP or less would drive, Chain driven. Support guard over chain. Approx 50" wide x 60' with 6" between rollers. Can be sold with Ad #19894. Call 800-459-2148 for more info.
$ 15,000
Barn Sweep, 55' x 4'. Can be sold with S&W Band Mill Ad #19894. Call 800-459-2148 for more info.
Hydraulic pump motor and tank. Call 800-459-2148 for more info.
$ 24,500
Heavy Duty Slat Conveyor - Overall length is 30 ft. - This conveyor has seen very little use - There are UMHW slides that the slats ride on underneath the conveyor and they show almost no wear - The slats are 54" wide and are made up from a channel and a 1/4" thick welded together - It has a 5 HP 3 three phase heavy duty electric motor and drive mounted on one end of the conveyor. Volts: 208-230/460 Amps: 14.8-13.6/6.8 - New, a conveyor of this size is $70,000-$80,000 - We have the ability to load the conveyor onto a flatbed trailer Call 800-459-2148 for more info.
$ 3,750
Shop built gang saw, 6" wide x 6" thick capacity, line-shaft ready, includes extra blades and spacers, recently in production and in good working condition
$ 55,000
40000 BF Kiln with Boiler for sawdust or chips. Call 800-459-2148 for more info.
Call for Price
Chip Conveyor Approx 400' Removed from closed mill with low hours. Some new conveyor included.
drop belt, approx 20" wide x 12' long, hyd drive, good working condition
$ 5,000
roll case approx 24" wide x 30' long, end section has spirals, good working condition
Call for Price
